Teeter X Series User manual

Specifications subject to change without notice.
© COPYRIGHT 2020 Teeter; International law prohibits any copying. 0920-0
EN
Disassembling the Inversion Table
Figure 1: Start by disconnecting the inversion
table into its primary components: Table Bed,
A-Frame, Main Shaft with Ankle System, Accessories,
Hardware, Handles*, and Roller Hinges. DO NOT
disassemble the product into more components
than the parts listed below.
Please be sure to include all components of the inversion table in your returned order, including the
accessories and instructions, otherwise you may not be eligible for a complete refund.
Begin by using the original box and bags that came with the inversion table. If you do not have the original
box, contact Teeter Customer Service at 800-847-0143. Product returned in an unauthorized packing
container may not be eligible for a complete refund.
NOTE: Figures do not show all bags used in repacking for easier viewing of box assembly.
1
2
3
5
4
Table Bed Accessories & Hardware
Handles
Roller Hinges
A-Frame
Main Shaft with
Ankle System
Disassembling the Table Bed
Figure 2: Ensure all the accessories have been
removed from the Table Bed and place the Table Bed
face-down on the floor. Remove the two Bolts from
the Support Beam by using the 6mm Allen Wrench
to steady the bolts, and then loosen the Nuts from
the Bolts with the 10/13mm Open-Ended Wrench.
4
6
6
1
23
5
X SERIES REPACKING GUIDE
Figure 1
Figure 2
Figure 3
*For Stretch Max Handle disassembly on the X2
and X3: ONLY untighten the bolt on the spreader
arm enough to lift the bottom of the handle off
the spreader arm bolt (Figures 1a & 1b). DO NOT
fully untighten the bolt as this will de-stabilize the
A-frame.
Figure 1a Figure 1b
Repacking the Table Bed
Figure 3: Start repacking the inversion table by
placing the Table Bed face-down into the box off
to one side as shown.

Figure 4a
Figure 4b
Figure 5b
Figure 5a
Repacking the A-Frame
Figure 4a & 4b: Position the A-Frame in the box by
first pulling up on the Support Beam of the Table
Bed with one hand and overlapping it over the
Crossbar of the A-Frame while sliding the A-Frame
into the box as shown.
Repacking the Ankle Lock System
For T-Pin Ankle Lock:
Close the T-Pin to the last hole setting (Figure 5a).
Then place it Ankle System-side down at an angle
next to the Table Bed on top of the plastic bag
(Figure 5b).
For EZ-Reach Ankle Lock:
Make sure the EZ-Reach Ankle System is open to
the second notch (Figure 5c). Place Ankle System-
side down at an angle next to the Table Bed on
top of the plastic bag, with the EZ-Reach Handle
tucked under the Crossbar of the A-Frame
(Figure 5d).
For Deluxe EZ-Reach Ankle Lock:
Close the Deluxe EZ-Reach Ratchet to the
smallest setting (Figure 5e). Place the Main Shaft
with Ankle Lock into the Large Bag to prevent
scratching. Place the Ankle Lock face-down next
to the Table Bed as shown (Figure 5f).
Figure 5c
Figure 5d
Figure 5e
Figure 5f

Figure 6
Repacking the Small Parts
Figure 6: Slide the Handles and Roller Hinges into a
Medium Bag. Slide the small Accessories, Hardware,
and Product Support Materials into a Small Bag and
pack all the parts as shown. The larger Accessories
including the Lumbar Bridge and Head Pillow can
remain loose in the box.
Sealing the Box & Attaching the Label
Seal the large box securely with packing tape, affix the return label and mark your
Return Authorization Number (RA #) on the outside panel of the box.
IMPORTANT: Teeter Inversion Tables cannot be returned without a Return Authorization Number.
Please contact Teeter Customer Service at [phone] or email [e-mail] for assistance.
USA: Teeter
9713 233rd Ave E, Suite A
Bonney Lake, WA 98391
Toll Free: 800-847-0143
Fax: [phone]
teeter.com | [e-mail]
If you have any trouble assembling the equipment, or questions
about its use, please contact customer service.
USA: 800-847-0143 or [e-mail]
International: [e-mail]