Amart Furniture Signature 65927 User manual

ASSEMBLY INSTRUCTION
LA SALLE MK3 EXTENSION DINING TABLE
ITEM CODE 65927
65927
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084

1
IMPORTANT: CARE GUIDE FOR YOUR
TIMBER FURNITURE
•Congratulations! You have just purchased a quality product from Amart
furniture, Australia's largest discount furniture retail store. Please read on for
important information regarding your purchase.
•A multi-step finish is applied to all our furniture, but all wood comes from
nature. Because of this, there will be natural variations in surface texture and
grain like knots, mineral streaks and sap runs that may affect the finish.
•These differences in character are not defects, but distinctions that make
each piece of furniture unique.
•Our furniture is built to last. Following these steps for basic care should
protect your investment for years to come.
•Dust frequently with a clean damp lint-free cloth. This will help remove
abrasive build up which can damage a finish over time.
•Do not place hot objects on any furniture surface. Always use a hot plate or
placemat. Laminate and lacquer finishes on table tops provide added scratch
and heat resistance to our furniture, but they can still be damaged without
proper care.
•Avoid exposing your furniture to strong sunlight, heat outlet, open windows
or dampness. Prolonged exposure to direct sunlight can fade the finish of
your furniture, while extreme temperature and humidity changes can cause
cracking or splitting.
•Do not expose your furniture to any liquids. Never allow water to sit on your
furniture. Alcohol, nail polish and perfume are also dangerous as they will
dissolve the lacquer finish on contact and may require professional repairs.
•Do not allow plastic to come in direct contact with your furniture. Chemicals
in the plastic of placemats etc may soften and mark the finish if left in contact
with the furniture for a period of time.
65927

PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage
the product
2. Take care when lifting. Product should be assembled as near as possible to the point
of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
4
Allow at least 45min you will need 4 people
65927
2

A M6 X 45 BOLT 8
PCES B M8 X 100 BOLT 8 PCES C M6.5 X 19 FLAT WASHER 8 PCES D M6.5 X 9 SPRING
WASHER
8
PCES
E HEXAGON NUT 8
PCES F M8.5 X 30 FLAT WASHER 8 PCES G M8.5 X 19 FLAT WASHER 8 PCES H M8.5 X 13 SPRING
WASHER
16
PCES
I ALLEN KEY 1 PCE J WRENCH 1 PCE K M6 x 70 BOLT 8
PCES L M6.5 X 13 FLAT WASHER
ATTACHED TO TABLE ATTACHED TO TABLE
M M6.5 X 9
SPRING
WASHER
8
PCES N M8 X 30 TIMBER DOWEL 4 PCES
ATTACHED TO TABLE ATTACHED TO TABLE
Part DESCRIPTION Qty In box Part DESCRIPTION Qty In box
1 TOP TABLE 1 1 3 CROSSBAR 1 1
2 PEDESTALS 2 2 4 LEGS 2 2
PARTS LIST
65927
3
1
4

Step 1
You should have started by opening box 1, upside down. Keep the
table top inside the box until later advised.
Step 2
As per the diagram below, detach the two rails with the Allen Key
provided (item I). You will need to re-attach these pieces later, so
please safely store the bolts, flat washers and spring washers (Items
K,L and M). Leave the timber dowels (item N) in their place, or place
them back in if they have slipped out.
Step 3
Now, please open box number 2, the legs and pedestal. When
removing the pedestals (part 2) be careful to keep the pedestal
standing upright at all times with the threads facing up.
65927
4

You will need
E hexagon nut 4
PCES
F M8.5 x 30 flat
washer 4 PCES
H M8.5 X 13
SPRING
WASHER
8
PCES
J Wrench 1
PCE
Step 4
Now attach one of the rails removed from step 2 to a pedestal (part
2). Start by placing the rail through the threads, onto the pedestal
with the threads facing up. This is a 2 person job with one person
holding the pedestal at all times. Next place the M8.5 x 30 flat
washer (item F) through the thread. Then insert the M8.5 x 13 spring
washer (item H), finally fasten the hexagon nut (item E) with the
wrench provided (item J). Repeat for other 3 threads, loosely
fastening each nut to secure, then coming back in a clockwise order
tightening them all. Do not over tighten, over tightening may damage
surface of item.
65927
5

Step 5
Now we’ll be attaching the pedestal and rail structure to the table
top. Start by placing the pedestal and rail structure into position
guided by the dowels in the table top. Then fix the pedestal and rail
structure with the 4, M6 x 70 bolts (item K), 4, M6.5 x 13 flat washers
(item L) and 4, M6.5 x 9 spring washers (item M) removed from step
2 with the Allen key provided (item I).
Step 6
Please repeat step 4,5 and 6 with the remaining pedestal and rail.
K M6 X 70 BOLT 4
PCES L M6.5 x 13 FLAT WASHER 4 PCES M M6.5 X 9 SPRING
WASHER
4
PCES I ALLEN KEY 1 PCE
YOU WILL NEED
65927
6

Step 7
Assembling you bolts (item B), spring washers (item F), and flat
washers (item G), as per diagram below.
B M8 X 100 BOLT 8
PCES F M8.5 X 13 SPRING
WASHER
8
PCES G M8.5 X 19 FLAT WASHER 8 PCES I ALLEN KEY 1 PCE
YOU WILL NEED
Step 8
Taking the assembled bolts from step 7 attach a leg to a pedestal,
using the Allen key (item I). As per image below.
Step 9
Repeat for the other leg and pedestal.
65927
7

A M6 x 45 BOLT 8
PCES D M6.5 X 9 SPRING
WASHER
8
PCES C M6.5 X 19 FLAT WASHER 8 PCES I ALLEN KEY 1 PCE
YOU WILL NEED
Step 11
Attach the crossbar to the legs as per diagram below, using the
assembled bolt sets from step 10.
Step 10
Assembling you bolts (item A), spring washers (item D), and flat
washers (item C), as per diagram below.
65927
8

Step 12
The final step is to flip the table over. This requires 4 people, do not
attempt alone. Before starting, double check that both latches are
firmly secured. If not follow the diagram below.
Next start with lifting the table out of its packaging. Have one person
take a corner each.When swinging the table the right way up, do not
pivot on the legs
Assembly is complete.
65927
9