GFW NORDICA 2 DOOR 4 DRAWER WARDROBE User manual

CATANIA 2 DOOR 1 DRAWER WARDROBE
ASSEMBLY INSTRUCTIONS
Thank you for purchasing the CATANIA 2 DOOR 1 DRAWER WARDROBE. Please read the
instructions carefully to ensure safe operation of the product.
Size: 790 x 515 x 1950mm
PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction.
Carefully open the pack supplied and check the contents against the parts and ttings check list. Do not
destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
CAUTION: There are small components used in the construction of this unit. These loose items should be
kept away from young children whilst assembling your unit to avoid the danger of choking hazards.
Tools Required
V1 2022.07
Page 1of 21
3.5m/12'x 2
Person Required Approximate
Assembly Time
1.5 Hours

V1 2022.07
Page 2of 21
IMPORTANT - READ CAREFULLY - RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
INFORMATION
�Due to the size of this product we recommend that it is assembled in the room intended for use.
�When you are ready to start, make sure that you have the right tools, plenty of space and a clean, dry area for
assembly.
�Unwrap all packaging materials and place the components on top of the carton box or on a clean floor to
prevent it from scratching.
�Check the pack and make sure you have all the parts listed.
�Ensure that this product is fully assembled as illustrated before use.
�Check all screws or bolts are tightened and inspect regularly
�This product should only be used on firm, level ground.
�Keep small parts out of reach of children.
�Make sure the legs remain in contact with the ground.
�Tools not included.
WARNINGS
�DO NOT use power tools to construct this product.
�DO NOT over tighten screws or bolts.
�DO NOT use this product if parts are missing, damaged or worn.
�DO NOT sit or stand on the product.
�It is essential that this unit is xed to the wall with the brackets provided for safety reasons. NB wall xings are
not included. Please source suitable fixings for your wall type. If in doubt please consult a qualified
tradesperson.
�WARNING : Always ensure the area to be drilled is free from hidden electrical wires, water or gas pipes.
CARE INFORMATION
�Never use scourers, abrasives or chemical cleaners.
�To clean wipe with a sponge and warm soapy water. Do not use solvent based cleaners or detergents as they
can bleach or damage the product.

V1 2022.07
Page 3of 21
Please check the pack contents before assembling the product. If any components are missing,
please contact your retailer. The ttings pack contains small items that should be kept away from
small children.
CODE QTYPART NAME
A
B
C
1
D
E
Top Panel
Bottom Front Bar
Side Panel - L
Side Panel - R
Parts
CODE
F
15 x 495 x 1930mm
DIMENSION
15 x 495 x 1930mm
15 x 495 x 790mm
15 x 80 x 759mm
15 x 65 x 759mm
QTY DIMENSION
15 x 65 x 759mm
PART NAME
Door - R 15 x 384 x 1669mm
1
1
1
1
1
1
1
1
Door Support 8 x 60 x 1615mm
1
N
Drawer Front 15 x 190 x 789mm
15 x 479 x 759mm
1
L
M
1
Drawer Side - L 15 x 140 x 350mm
G1
K
Bottom Support Bar
Fix Shelf
15 x 140 x 350mm
15 x 140 x 704mm
1
O
PDrawer Back
Drawer Support 15 x 80 x 335mm
Drawer Side - R
Front Bar
15 x 80 x 759mm
H1
Back Bar
G
1
15 x 65 x 759mm
I1
Top Support
15 x 384 x 1669mm
J1
Door - L
15 x 110 x 759mm
1
Bottom Back Bar
BACK
PANEL
BACK
PANEL
DRAWER
BOTTOM
3 x 344 x 713mm
1
Drawer Bottom
3 x 393 x 1850mm
Q
R
2
Back Panel

0 cm
1 cm
2 cm
3 cm
4 cm
Fixings (to scale)
0 cm
1 cm
2 cm
V1 2022.07
Page 4of 21
17x
M3.5 x 15mm
F
CSK Screw
14x
EU 24
C
Minix Bolt
37x
Dia. 8 x 30mm
D
Wooden Dowel
26x
#10 x 16mm
E
Tapping Screw
4x
M4 x 38mm
B
CSK Screw
4x
M6.3 x 40mm
A
Unita Screw
4x
M6 x 8mm
G
Euro Screw
6x
I
Nail Leg
20x
H
Nail Pin

V1 2022.07
Page 5of 21
14x
Dia. 15 x 12mm
J
Minix Cam
2x
K
U Bracket
1x
L
L Bracket
1x
L - 750m
M
Hanger
1x
M4
S
Allen Key
1 set x
14" (350mm)
N
Drawer Slide
6x
5/8”
P
Hinges
1 set x
14" (350mm)
O
Drawer Slide
Fixings (not to scale)
2x
1.2x15x32x75mm
Q
L-Mounting
Bracket
2x
D-16mm
R
Flat Washer

V1 2022.07
Page 6of 21
Layout Parts on Soft Surface
BACK
PANEL
BACK
PANEL
DRAWER
BOTTOM

GN
V1 2022.07
Page 7of 21
STEP 1
PLEASE ENSURE TO FIX THE SCREWS AS PER ABOVE POINTED HOLES
INSTRUCTION TO AVOID DISTORTION OF OVERALL LOOK OF PRODUCTS
SECOND HOLE
FRONT
TOP
BACK
4 x1 x

V1 2022.07
Page 8of 21
STEP 2
C
10 x
K
2 x

STEP 3
STEP 4
STEP 5
V1 2022.07
Page 9of 21
C
2 x
D
1 x
J
2 x

STEP 6
STEP 7
STEP 8
V1 2022.07
Page 10 of 21
D
20 x
D
2 x
FL
2 x
1 x