TEFAL GV9071 Pro Express Care Installation guide

What is the function of the Autoclean Catalys soleplate (according to model)?
This system prevents the soleplate from clogging. Its active coating eliminates fibres and
impurities that often become stuck to the plate and end up reducing its glide.
What is the ECO setting (depending models) for?
The «ECO» function allows you to reduce energy consumption. This means that less electricity
is used and therefore slightly less steam is generated.
Is it dangerous to have the water and electricity cables together?
No. The two cables are separately insulated; they are protected and rigorously checked.
However, if you notice that the cable is damaged, have it repaired by an approved repair centre.
Is lime scale a problem for steam generators?
The formation of lime scale is avoided because the water is not in direct contact with the heating
element, which is located outside the tank. However, the tank should be rinsed after 10 uses to
avoid lime scale deposits.
What is the difference between a steam generator and a steam station?
A steam generator is the most powerful iron that generates vast amounts of powerful steam in a
separate boiler unit and pumps that steam constantly and consistently through the iron's soleplate
straight into the clothes. The benefit is that this halves your ironing time and produces fantastic
ironing finishes. A steam station is similar to an ordinary iron but has a larger water tank. The
water is pumped up to the iron and the steam is generated in the iron not a separate boiler unit.
The steam output is constant but not as powerful as a steam generator.
The steam is generated under pressure. Is there any risk?
No. The pressure is at a relatively low level. Your appliance has two safety systems.
• A valve avoids any excess pressure and, in the event of malfunction of the appliance, allows the
surplus steam to escape.
• A thermal fuse to avoid any overheating.
What are the “2-in-1", "Smart technology" and "easy control” functions for (depending on
model)?
These functions means that your steam generator is fitted with an electronic regulation which
offers you the perfect temperature and steam combination allowing you to iron all your ironable
fabrics without risk and without having to sort them.
Is it normal to hear a rattling noise from time to time?
Yes, this is normal. This is due to the flow of cold water into the boiler that contains hot water.
A short time after use, I can hear a metallic sound.
The internal parts may make metallic noises with the change in temperature. There is nothing
wrong with it.
The iron doesn't glide very easily.
Some laundry starches and synthetic fibres may stick to the surface of the iron. Please clean the
Iron's surface.
The soleplate is dirty or brown and may stain clothing.
• Your iron is too hot, see our recommendations on temperature control settings in your product
manual.
• You are using starch. Only spray starch on the reverse of the fabric to be ironed.
Brown streaks come out of the holes in the soleplate and stain the laundry.
• You are using chemical descaling products or additives in the water. You should never put
these products in the water tank. If this is the case, contact an Approved Service Centre.
• Your washing has not been rinsed sufficiently or you are ironing a new item of clothing before

washing it. Ensure that you have rinsed your clothes thoroughly in order to to remove soap
deposits or chemicals from new garments which could stick to the iron.
Why is steam coming from the iron or generator base when switched on but the iron is not being
used?
The generator's safety mechanism has activated. You need to get the generator checked by an
authorised service agent.
Why does my red water light keep flashing?
If your red water light is flashing there is no water in the water tank or the tank is not fully or
firmly pushed down.
Why is my generator is not producing steam?
If the boiler does not operate or the red light on the control panel comes on even though there is
still water left in the tank, we suggest you check the water tank is not empty. You can also check
the removable water tank (depending on model) is pressed down firmly in place and press the
restart button located on the control panel. Also the steam output control dial may be set at
minimum (depending on Model); therefore turn the dial up to increase the steam.
Some waterdrops drip out onto the floor during ironing.
It is normal. Your iron generates a lot of steam; this steam is condensing on the board. Some
waterdrops could appeared underneath the ironing board and fall on the flooring.
Why is my iron dripping water?
Place the iron's temperature control to the type of fabric to be ironed and set the steam output to
match (If the setting temperature control is on Synthetics, the setting steam control must be on
MIN).
Is it normal for the steam cord to get warm during ironing?
Yes. However, if you notice that the steam cord is damaged, have it repaired by an authorised
service partner.
Steam escapes from the anti-scale Valve Plug.
The anti-scale valve plug may be tightened incorrectly or the seal on the inside of the cap has
perished.
Why does my orange light keep flashing after I have just rinsed the boiler?
After rinsing the boiler, you need to press and hold the restart button for about 3 seconds to stop
the light flashing.
Should I be concerned about any noises from my generator?
No. When starting or using the steam generator you may hear a pumping or vibrating noise along
with a clicking sound. This is completely normal and is just the pump injecting water into the
boiler, or the steam valve opening.
How do I clean the soleplate?
• The Durillium soleplate:
Regularly clean the soleplate with a damp, non metallic washing up pad. For easier, non-
corrosive cleaning of your iron's soleplate, use a damp sponge on the soleplate while it is still
warm.
If cleaning dirt off is an issue, use the stick which is made specifically for cleaning the Durillium
soleplates.
• The stainless soleplate:
Clean the soleplate of your iron when it is cool with a damp cloth or a non-abrasive sponge.
• The autoclean soleplate:
It is recommended that you use a soft damp cloth on the warm soleplate, in order not to damage

the surface.
Warning: The use of iron cleaner will cause damage to your soleplate's autoclean coating.
How do I descale my steam generator?
Descaling operation is not needed for the steam generator, nevertheless, you could rinse the
boiler every 10 uses (refer to user manual).
Never use any descaling agent or vinegar when rinsing the boiler: they could damage it.
• Models with scale collector: Rinse the scale collector under water. The next time you use your
generator, press the "restart" button to turn off the orange "Anti-calc" light (depending on
model).
• Models without scale collector: Rinse the boiler. The next time you use your generator, press
the "restart" button to turn off the orange "Anti-calc" light (depending on model).
How do I maintain my steam generator?
Before any maintenance, make sure that the appliance is unplugged and that the soleplate, boiler
and iron rest have cooled down (at least 2 hours after ironing).
Do not use any maintenance or descaling product to clean the soleplate or the base unit. Never
hold the iron or its base unit under a running tap.
Cleaning the base unit:
• Wipe the plastic parts from time to time using a slightly damp soft cloth.
Maintaining the boiler (once a month):
• Please note: To prolong your boiler's efficiency and avoid scale deposits, you must rinse the
boiler every 10 uses (around once a month).
• Check that the generator is cool and has been unplugged for more than 2 hours.
• Slowly loosen the boiler cap. If your generator boiler has an anti-calc rod, take this out and
rinse it under the tap before placing it back in the boiler.
• Use a jug to fill the boiler with tap water until it is 3/4 full.
• Shake the base unit gently for a few seconds then empty it completely over the sink.
• For best results, we recommend that you perform this operation once again.
If you live in a har
How can I avoid shiny marks on fabric?
Shiny marks can appear on some fabrics, especially on dark coloured fabrics. We would advise
ironing dark clothes inside out and using the correct temperature.
If ironing mixed-fibre fabrics, set the temperature for the most fragile fibre.
Important: The iron takes longer to cool down than to heat up. We recommend that you start with
fabrics to be ironed at a low temperature
What type of ironing board should I use?
Choose a board that is height-adjustable to adjust it to your body. It should be steady and robust
so that you can place the ironing appliance on it.
The board should be perforated to allow the steam to pass through the fibres of the fabric to
soften it and make ironing easier. The ironing board cover should also be suitable to allow the
flow of steam through.
What water should I use for ironing?
• Tap water:
Your appliance has been designed to work with tap water. If your water is very hard, mix 50%
tap water with 50% distilled water (available in stores).
In some regions near the sea, the salt content in your water may be high. In this case, use distilled
water only.

• Softener:
There are several types of softeners and most of them can be used in your appliance. However,
some softeners, and particularly those that use chemical products such as salt, may cause white
or brown stains, this is particularly the case with filter jugs. If you experience this sort of
problem, we suggest you try using untreated tap water or bottled water.
Remember:
Do not use rain water or water containing additives (such as starch or perfume) or water from
clothes dryers, water from refrigerators, air conditioners etc. These additives may affect the
properties of the steam, and together with high temperatures can cause deposits to form in the
steam chamber which could soil your laundry and lead to premature ageing of the appliance.