TELECO AUTOMATION TVDAY A01 Series User manual

Wi-Fi interface, App-programmable, to remotely radio control
all devices from Smartphones.
SIMPLE INSTRUCTION
Product code:
1.0 Characteristics
Feautures
• Available in both 868.3MHz and 916MHz frequencies.
• Easy access via Wi-Fi or mobile network from any compatible device.
• Up to 50 programmable device commands.
• Possibility to create scenarios.
• Weekly timer to send commands at a specic date and time.
WISE CONTROLS APP
* The Blue Series receivers are bidirectional. They can receive
and execute commands and send the status back to DAISY BOX
LED: Wi-Fi Network
Wi-Fi
LED: Radio commands
Transmission
Button: Reset Wi-Fi
Network conguration (*)
* The memorized transmitters are not deleted.
1. +12 ÷ 24Vdc
2. GND (-)
3. +5Vdc
4. COMMON
5. N.O. CONTACT INPUT The product guarantees IP54 rating
if properly assembled.
Thermoplastic ABS
Not suitable for direct UV exposure
- Transmission frequency 868.3 MHz (TVDAY868A01)
916MHz (TVDAY916A01)
- Power supply 5 / 12 ÷ 24Vdc
- Operating temperature range -20° ÷ +50°C
- Max. possible virtual transmitters 50
- Protection IP54
- Material of the box and its cover Thermoplastic ABS
- Network Wi-Fi module 802.11 b/g/n
- Frequency band 2.4GHz
1.1 Technical specification
DAISY BOX
Via dell'Artigianato, 5 - 31014 Colle Umberto (TV) ITALY
Tel. [phone] Fax [phone]
Web site: www.telecoautomation.com
DATE: 01/06/18 REV: 2.0
G304BK-CO-SER1
colore come G304BK-CO-SER
TVDAYxxxA01
868.3MHz
916MHz
868.3MHz
916MHz
Via dell'Artigianato, 5 - 31014 Colle Umberto (TV) ITALY
Tel. [phone] Fax [phone]
Web site: www.telecoautomation.com
DATE: 01/06/18 REV: 2.0
G304BK-CO-SER1
colore come G304BK-CO-SER
M
115 mm
65 mm
25 mm
15 mm
*
DOC.: TEMP_EN
TVDAYXXXA01_MR DATE:03/04/19
This document is the property of Teleco Automation Srl who reserves all reproduction and copying rights

2.0 Installation
Download the app Wise Controls from App Store or Google Play. Check the compatibility with
your device rst. Once downloaded, it is possible to use it in DEMO mode, even without any
DAISY BOX paired.
3.0 Registration
The smartphone must be connected to an internet network. Follow the procedure here below described:
1. Tap on “Create
new account”.
2. Fill the elds with the
information required.
3. Once lled the elds
tap on “Sign In”.
4. Check email to
conrm registration.
5. “Log In” with User
and PWD assigned.
4.0 First configuration with Android device
1. Run the Daisy APP
Name: Orange_WiFi_Network
Password: 12345678
3. Take note of WiFi
Name and Password.
4.1 First configuration with IOS device
1. On your phone, set up
the Daisy_4C55xx WiFi
network and run the
Daisy App.
3. Take note of WiFi
Name and Password.
4. Select your WiFi
network.
2. Tap on “Create
rst Installation”.
In order to connect Daisy BOX to the WiFi network the router doesn’t have lter blocks.
In case of connection issues please contact the system administrator.
Mandatory: Android version 4.4 KitKat or later.
Mandatory: IOS version 12.0 or later.
2.4GHz
Warning: Verify that the option to connect to networks without Internet access is enabled in the phone.
5. Enter Home
Network’s Password
and tap “Continue”
4. Select your WiFi
network.
2. Fill the eld with the
Code written on the
Daisy box label
5. Enter Home
Network’s Password
and tap “Continue”
Email
Password
Create new account
Email
Password
Conrm Password
First Name
Last Name
John
Smith
[email protected]
********
********
Sign In
[email protected]
Log In
********
Code: 4C55CC164F25
Code: 4C55CC164F25 5GHz
Orange_WiFi_Network
Enter Orange_WiFi
Password
12345678
Continue
WiFi
Daisy_4C55xx
Create First Installation Name: Orange_WiFi_Network
Password: 12345678
2.4GHz
5GHz
Orange_WiFi_Network
Continue
12345678

Transmission
Active
Not Active
Status Wi-Fi connection
Waiting for
connection
Connecting
Connecting
Connected
5.0 Led indications
BLUE LED: Wi-Fi Network.
RED LED: Radio commands
Transmission.
LINK: Wi-Fi Network
...
1 s
...
1 s
...
0.5 s
...
0.5 s
ON
TX (RED LED): Radio commands
ON
OFF
...
0.5 s
...
Blue Blue Blue
Blue Red Blue Red Blue Red
0.5 s 0.5 s
6.0 Main menu
Direct connection through WiFi router
Cloud connection
No connection (Board not reachable)
Tabbar: Home - Scenarios - Favorities
6.1 Setup rooms
1. Create new
rooms accessing
the menu “Rooms”
in Setup.
Note: swipe a listed room left to delete it.
2. Tap (+) to add a
room.
3. Tap (Room) to
enter in the next
menu.
4. Set the name and assign a picture
amongst the 6 provided (Select your
room) or select a picture of your device
gallery.
Blue Blue Blue
Blue
DAISY BOX
Via dell'Artigianato, 5 - 31014 Colle Umberto (TV) ITALY
Tel. [phone] Fax [phone]
Web site: www.telecoautomation.com
DATE: 01/06/18 REV: 2.0
G304BK-CO-SER1
colore come G304BK-CO-SER
ROOMS ROOM ROOMName:
Select your room
Load your room
ROOMS Delete

6.2 Adding commands to a room
1. Tap “+” to add remote
commands. Select
the type of controlled
device from the list.
2. Tap the transmitter
to add.
3. Assign a “Name”.
Add to Favourites
Enable if the receiver is Blue Series
Enable to set the timers
Note: swipe a listed
transmitter left to
delete it.
7.0 Scenarios
1. Create new
scenarios accessing
the menu “Scenarios”
in Setup.
2. Tap “+” to add a scenario. Set the Name
and assign an icon amongst the 9 provided.
3. Tap “+” to add
remote commands
from any room.
4. Select the type
of controlled device
from the list.
5. Tap (Light 1)
to add the first
command.
6. Tap (GREEN) to
chose the command
the (OK).
7. The rst device
configured for the
scenario appears
on the display.
8. Repeat steps
3-4-5 to add the
other devices to
the scenario.
Living
Name: Name: Light 1
RGB 7 COLOR
Select your room
Load your room
Change type
Delete
Name
SCENARIOS
Choose Icon
Scenario Scenario 1
Light 1
Kitchen
7CH
Note: swipe a
listed scenario left
to delete it.
Light 1
GREEN
Light 1
GREEN
Living
Scenario 1 Scenario 1
Light 1
ON
Living
7CH
Button5
Kitchen
2CH
Button1
Kitchen
Delete
Scenario
Kitchen
2CH
Living
Scenario 1
Scenario 1
OK
Scenario 1

7.1 Advanced scenario programming
Once the scenario has been completed, it’s possible to assign it to a transmitter button or to a wired N.O. button
connected to the input 4-5.
Tap and press the transmitter button to assign.
Tap and press the transmitter button to delete.
Tap to delete all the associated transmitter buttons.
Note: When transmitters or the wired input
are programmed, this icon is ON
8.0 Timers
1. Create new timer
accessing the menu
“Timers” in Setup.
2. Tap “+” to add
a timer.
4. Tap (GREEN) to
chose the command
5. Enable the
timers. Set the hour
for the timers.
7. Repeat steps 2 and
3 to add timers to the
other devices.
Note: swipe a listed timer left to delete it.
3. Tap “Light 1” to
add a timer.
6.Tap “Save Changes”.
Not used
Scenario
TIMERS
GREEN
Weekday Timer: 17:17
Weekend Timer: 21:17
Living
Light 1
Kitchen
7 CH
2 CH
Green Light1 Living
15:32
15:32
FAN 2 CH Kitchen
13:17
17:17
Buttons6 7CH Kitchen
10:08
11:00
Delete
Green Light1 Living
15:32
15:32

Enable timers
2. Tap (Active all
timers) to enable
the timers.
3. It’s possible to set weekdays-weekend group. Tap
on the day names to add in weekdays groups.
Note: To operate the timers must be enabled following the procedure described below:
1. Tap gear icon.
9.0 Select Boards
1. Tap (Boards) to
enter in the next
menu.
2. Tap the chosen
board. To add new
board tap (+).
3. To pair the
board tap (Select).
Board n. 2
Board n. 1
11.0 Share installation (SIX HOURS)
Note: Before starting, it is necessary to carry out the Registration procedure on the new
smartphone described in the paragraph 3.0
1.Tap(Share installation).
Congurated smartphone
2. Fill the eld with the email of the new
smartphone. Tap (Share ...) installation.
Congurated smartphone
3. Accept the invite to share
the installation.
New smartphone
[email protected]
Share Six Hours
Share Six Hours
Cancel
Monday
Tuesday
Wednesay
Thursday
Friday
Saturday
Sunday
Viadell'Artigianato,5 - 31014ColleUmberto(TV)ITALY
Tel. [phone]Fax [phone]
Website:www.telecoautomation.com
DATE: 01/06/18 REV: 2.0
G304BK-CO-SER1
colore come G304BK-CO-SER
Viadell'Artigianato,5 - 31014ColleUmberto(TV)ITALY
Tel. [phone]Fax [phone]
Website:www.telecoautomation.com
DATE: 01/06/18 REV: 2.0
G304BK-CO-SER1
colore come G304BK-CO-SER
Log In
********
[email protected]
Monday
Tuesday
Wednesay
Thursday
Friday
Saturday
Sunday
BOARDS
Board n. 1
Board n. 2
Board n. 2
Select
Share six hours

14.0 Home Page
Once congurated the rooms with the transmitters tap (done) to enter in the (Home) page.
12.0 General Setting
2. Choose the
Refresh time and tap
(Setup).In alternative
tap (Refresh Now).
3. In order to set a new
password tap (Change
Password).
Scenario set
Favourites transmitters set
Rooms set
Setup Menu
Hourly
Refresh Now
Setup
Swipe down
to Update the
conguration.
TIPS
13.0 Info page
1. Tap (Info) to
enter in the next
menu.
General conguration information
Status information of Daisy board
Software and rmware information
1. Tap (General
Setting) to enter in
the next menu.
GENERAL SETTING
Refresh Now
Setup
Change Password
Info
Done

1. Tap (Living or
Kitchen room icon)
to enter in the next
menu.
2. Tap (Light icon) to
enter in the next menu. Lights
commands
OFF
command
Dynamic icon
3. Tap (7CH or 2CH
transmitter) to enter in
the next menu.
Press the virtual
button
14.1 Wise transmitter
Note: To operate the Daisy transmitters must be memorized in the receveirs. See par. 14.2 and par. 14.3
WISE TRANSMITTERS
14.2 Memorization
For its proper functioning the Wise transmitter must be memorized in the controlled receiver.
Refer to instruction manual of the receiver for the procedure of memorization.
Wise transmitter
Feedback
(tap to ask)
Light 1
Fan
Screens
Press the virtual
button

14.3 Remote memorization of other radio codes from standard transmitter
Note: The button P3 is located inside the standard transmitter. The added radio code will have the same functions as the code used for memorization.
This procedure is compatible with any type of transmitter.
1 s
P3
New
< 5 s
continuous
sound
Memorized
< 5 s
continuous
sound
Standard transmitter Wise transmitter
Press button P3 of the memorized standard transmitter and hold. The buzzer emits a continuous sound. Press
a button relative to an already memorized code. The buzzer stops for 1 second and then starts the continuous
sound again. Press the virtual button on the Wise transmitter relative to the new code to be memorized. Successful
memorization is indicated by the intermittent sound of the buzzer.
15.0 Sending Scenario
1. Tap (Scenario
icon) to enter in the
next menu.
2. Tap (Scenario
icon) to send
scenario.
3. Tap (Yes) to
send scenario.
Note: Tap (i) icon to get information
about the scenario set.
16.0 Reset Wi-Fi Network configuration
Button: Reset Wi-Fi
Network conguration (*)
Press (P) once and hold for 5s:
* The memorized transmitters are not deleted.
Daisy
Send Scenario
YesNo
Blue Red Blue Red Blue Red
(5 s)
Alternatively hold the button (P) down and at the same time turn on the power:
Blue Red Blue Red
ON Blue Red Blue Red Blue Blue
0.5 s 0.5 s
Memorized
...
Scenario i
Scenario i
2CH(CH2)
7CH(CH5)
Light1(Blue)
Viadell'Artigianato, 5 - 31014 Colle Umberto (TV) ITALY
Tel. [phone] Fax [phone]
Website: www.telecoautomation.com
DATE: 01/06/18 REV: 2.0
G304BK-CO-SER1
colore come G304BK-CO-SER
...
...
1 s 1 s 1 s 1 s 1 s 1 s
...
...
... ... ...
0.5 s 0.5 s
0.5 s 0.5 s 0.5 s 0.5 s

Problem Solution
First conguration procedure:
Blue and Red LEDs ashes alternately for long time
Wait until the LEDs stop ashing even if appear the
message “Connection between board and phone
failed”.
If the LEDs continue to ash, check that the router
does not have lters blocks set.
First conguration procedure:
Blue Led ashes slowly - Connection failed
Check that the data are correct and repeat the rst
installation procedure.
First conguration procedure:
GPS connection problem
Verify that the GPS function is enabled and set to
high precision mode
Normal operating mode:
Disconnection from the WiFi network: Blue and Red LEDs
ashes alternately
Verify that the router is powered and connected to
internet.
Normal operating mode:
No internet connection - Blue LED ashes each 0.3s. Check the router’s internet connection
Normal operating mode:
Emergency mode - Blue LED ashes each 0.1s.
Available only direct commands.
Check the router’s internet connection
17.0 Troubleshooting (what to do IF…)
BLUE LED
RED LED
DAISY BOX
WISE APP
Via dell'Artigianato, 5 - 31014 Colle Umberto (TV) ITALY
Tel. [phone] Fax [phone]
Web site: www.telecoautomation.com
DATE: 01/06/18 REV: 2.0
G304BK-CO-SER1
colore come G304BK-CO-SER

PRODUCT INSTALLATION: The product at issue must be installed, commissioned and maintained only by licensed
and authorised people, respecting the laws concerning the electrical installations. The manufacturer is not responsible
for any damage due to wrong installation or improper use.
SAFETY INFORMATION: The radio signal reception of the device could be disturbed by the presence of electrical
disturbances being transmitted by other appliances working on the same frequency or if the product is somehow
shielded by metal parts.
The manufacturer, Teleco Automation s.r.l, declares that the type of radio equipment is compliant with Directive 2014/53/
EU. The full text of the EU compliance declaration is available at the following Internet address: www.telecoautomation.
com/ce.
In the view of a constant development of their products, the manufacturer reserves the right for changing
technical data and features without prior notice.
INFORMATION TO USERS under art. 14 of the 2012/19/EU DIRECTIVE OF THE EUROPEAN PARLIAMENT AND
COUNCIL of 4 July 2012 on waste electrical and electronic equipment (WEEE). The crossed bin symbol on the
equipment, or its packaging, indicates that the product must be collected separately from other waste at the end of
its useful life and not with mixed urban waste. Please contact your municipality, or local authority, for all information
regarding the waste sorting systems available in the area. The retailer is obliged to collect the old equipment
free-of-charge when the customer buys a new equivalent equipment. This is to encourage correct recycling/disposal.
Appropriate waste sorting for the subsequent recycling,reatment and disposal in an environmentally sound way of the
disused equipment avoids negative effects on the environment or human health and favours the re-use or recycling of
the equipment’s materials.
IMPORTANT! READ CAREFULLY THESE INSTRUCTIONS BEFORE INSTALLING AND
COMMISSIONING THE PRODUCT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Produced by
This document is the property of Teleco Automation Srl who reserves all reproduction and copying rights