Philips srp3014 User manual

SRP3014
Always there to help you
Register your product and get support at
www.philips.com/support
User manual
GrayTurqoise Duotone
Black / PMS300
Question?
Contact
Philips
Question?
Contact
Philips
Question?
Contact
Philips

2 EN

English
EN 1
Contents
Contents
1 Your universal remote 2
Introduction 2
Overview of the universal remote 2
Supported devices 3
2 Get started 4
Insert batteries (not included) 4
Set up the universal remote 5
3 Notice 9
Notice of compliance 9
Disposal of your old product and batteries 10
4 Service and support 11
Frequently asked questions 11
Need help? 11

2 EN
1 Your universal remote
Congratulations on your purchase, and welcome to Philips!To fully
benet from the support that Philips offers, register your product at
www.philips.com/welcome
Introduction
With the universal remote, you can operate up to 4 different devices.
Overview of the universal remote
a INPUT: select available source inputs (antenna, cable, etc.).
: power on or off.
: LED indicator
b Device selection buttons
a
b
c
d
e
f
g

English
EN 3
c LIVE: displays live TV programs.
LIST: displays a list of recorded programs.
INFO: displays on-screen channel information.
STREAM: shortcut to the Netix.
GUIDE: displays the program guide.
: play
: fast forward
: rewind
: pause
: stop
: record
d / / / : scroll the menu up/down/left/right.
OK: conrm your selection.
MENU: menu on or off.
BACK: go back one menu level or exit.
e : mute
LAST: return to the previous tuned channel.
CH+/CH-: go to the next/previous channel.
VOL: adjust the volume.
f A/B/C/D: context sensitivity buttons (A - yellow, B - blue, C- red,
D - Green).
g Digit buttons
ENTER: conrm the digit button selection.
(-): selects between one and two-gure channel numbers.
Note
• The button “STREAM” is pre-programmed as a shortcut to Netix. All other
streaming services such as Vudu, Amazon, YouTube and Hulu Plus etc may be
accessed through navigation.
Supported devices
Device name Description
TV TV, DTV
BD DVD player/recorder, Blu-ray player
STB Cable box, satellite receiver, IPTV, DVR, HDTV
decoder and TiVo
STR Streaming devices, Apple TV, Roku, Sony, WD TV,
Netgear

4 EN
2 Get started
Insert batteries (not included)
Warning
• Check the battery polarity when inserting in the battery compartment. Incorrect
polarity may damage the product.
Caution
• Risk of explosion! Keep batteries away from heat, sunshine or re. Never discard
batteries in re.
• Risk of decreased battery life! Never mix different brands or types of batteries.
Note
• When you replace the batteries, all user settings will be retained in the memory of
the universal remote for 5 minutes.

English
EN 5
Set up the universal remote
You must rst set up the universal remote before operating your
devices.
Manual registration
1 Switch on your device.
2 Press and hold the device selection button (e.g.TV) for 5 seconds
until the blue LED is on.
3 Look up the 5-digit code for your brand in the code list. Codes
are listed by the device type and brand name.The most popular
code is listed rst.

6 EN
4 Enter the rst 5-digit code using the digit buttons.
5 If the light is off, a valid code is saved. Otherwise, the light will ash
once, and then remains on for code re-entry.
6 Operate the device with the universal remote. If your device
responds correctly, it means you have entered the right code.
Otherwise, repeat from step 2, and enter the second code on the
list.
Note
• It is possible sometimes that your device only responds to some of the buttons. In
such case, set up with the next code in the code list, and try operating your device
again.

English
EN 7
Auto registration
1 Switch on your device.
2 Press and hold the device selection button (e.g.TV) for 5 seconds
until the blue LED is on.
3 Point at your device with the universal remote.Then press and
release to start searching the code for your brand. A different
infrared signal is sent every 2 seconds as the universal remote
searches, indicated by a blue flash.

8 EN
4 When the device is off, immediately press and release OK to save
the code.The blue LED indicator will turn off.
5 Operate the device with the universal remote. If your device
responds correctly, it means you have saved the right code.
Note
• Auto registration can be reversed, by pressing and releasing once more during
the auto registration process.This is helpful if you missed out the chance to press OK
within 2 seconds. Make sure that the device is rst powered on again.
• Repeat the same procedures to set up other devices.
max. 20
minutes