Teledyne Flir Saros DM Series User manual

427-0200-01-10 Rev 120
June 2021
This document does not contain any export-controlled information.
Saros™ PTZ
DM-Series Camera
Quick Install Guide
1 Check Contents
Make sure all of the items above are included in the camera kit.
This camera is a Class 1 Laser Product
that complies with IEC 60825-1:2014.
Caution
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
Attention
L'utilisation des commandes ou reglages ou l'execution des procedures autres
que celles specifiees dans les presents exigences peuvent etre la cause d'une
exposition a un rayonnement dangereux.

427-0200-01-10 Rev 120
June 2021
This document does not contain any export-controlled information.
2 Prepare to Install the Camera
2.1 Install FLIR Discovery Network Assistant
Download the FLIR Discovery Network Assistant (DNA) tool to a computer on the
same VLAN to which you will connect the camera, and then unzip the file. The
DNA tool does not require a license to use and is a free download from
www.teledyneflir.com > Products > Security > Thermal Security Cameras > Saros
DM-Series.
2.2 Perform a Bench Test (Optional)
You can test the camera or configure it for networking before mounting it. Follow
the instructions in 3.4 Connect the Camera and 4.1 Configure for Networking, and
then continue with 2.3 Select a Location.
2.3 Select a Location
Select a suitable location to mount the camera.
For advice on positioning and orienting the camera, see the camera's installation
and user guide.
Verify that the operating temperature range is between -40° ~ 55° C (-40° ~ 131°
F), 10-90% relative humidity (non-condensing).
For the list of mounting accessories available for the camera, see the FLIR
Security Cameras - Accessory Guide.
3 Install the Camera
3.1 Fit Mounting Hardware
If required, install the mounting hardware for the camera according to the
instructions in the camera's installation and user guide.
3.2 Route Network and Power
Properly install the power and network cabling in the mounting hardware so that it
is accessible when the camera is mounted.
Power: Universal Power over Ethernet (PoE) 60W 4 pair forced mode, 24 VAC,
or 30 VDC.
Ethernet: Cat5e or Cat6 cable. Ethernet is required for streaming video and
configuring the camera.
3.3 Mount and Secure the Camera
Mount and secure the camera according to the instructions in the camera's
installation and user guide.

427-0200-01-10 Rev 120
June 2021
This document does not contain any export-controlled information.
3.4 Connect the Camera
Connectors
Connector
Connection
1
UPOE
Attach a Cat 5e or Cat 6 cable from the network switch
to the RJ45 connector for a 10/100/1000 Mbps Ethernet
and PoE connection. If using PoE, use a FLIR CP-POE-
4P-60W-xx injector or a switch that supports Universal
PoE 60W 4 pair forced mode. For more information
about compatible injectors and recommended switches,
contact Teledyne FLIR support. Verify that the UPOE
connector LEDs are steady green and flashing yellow.
2
AC24V
(DC30V) IN
If using a 24 VAC or 30 VDC power supply, connect it to
the three-pin power terminal block plug according to the
pin assignment shown.
3
DEFAULT
To reset factory defaults at any time, press the Default
button for at least 20 seconds.
4
14-pin
terminal
block
Attach wires from external alarm and audio I/O devices
to the 14-pin alarm/audio I/O terminal block plug
according to the pin assignment shown.
3-Pin Power
Terminal Block
Pin
24 VAC
30 VDC
1
L (Live; white; positive)
Pins 1 and 3
(polarity N/A)
2
Ground (Earth)
3
N (Neutral; black; negative)

427-0200-01-10 Rev 120
June 2021
This document does not contain any export-controlled information.
14-Pin Alarm/Audio I/O
Terminal Block
Pin
Definition
Pin
Definition
1
Audio-Out
8
Not used
2
Ground (Audio I/O)
9
Alarm-In 4
3
Alarm-Out A1
10
Alarm-In 3
4
Alarm-Out A2
11
Alarm-In 2
5
Alarm-Out B1
12
Alarm-In 1
6
Alarm-Out B2
13
Ground (Alarm I/O)
7
Not used
14
Audio-In
Warning!
This product contains a battery that is soldered to the PCB.
There is a risk of explosion if the battery is replaced by an
incorrect type. Do not replace the battery. The battery
should be disposed of in accordance with the battery
manufacturer’s instructions.
4 Configure the Camera
You can configure the camera using the DNA tool, the camera's web page, or a
VMS.
DNA tool
Camera's web page
Discover camera IP address
•
Configure IP address, mask, and gateway
•
•
Configure DNS settings, MTU, and Ethernet speed
•
Change user credentials
•
•
Configure more than one camera at the same time
•
For more information about using a VMS to configure one or more cameras at the
same time, see the VMS documentation.
4.1 Configure for Networking
By default, DHCP is enabled on the camera and a DHCP server on the network
assigns the camera an IP address. For example, if the camera is managed by a
FLIR Horizon or Meridian VMS and the VMS is configured as a DHCP server, the
VMS automatically assigns the camera an IP address.
If the camera is managed by a FLIR Latitude VMS or is on a network with static IP
addressing, you can manually specify the camera’s IP address using the DNA tool
or the camera's web page. The camera's default IP address is 192.168.0.250.
To configure the camera for networking using the DNA tool:
a. Make sure the camera and the PC are on the same LAN segment.
b. Run the DNA tool (DNA.exe) by double-clicking .

427-0200-01-10 Rev 120
June 2021
This document does not contain any export-controlled information.
The Discover List
appears, showing
compatible
devices on the
VLAN and their
current IP
addresses.
In the DNA Discover List, verify that the camera's status is Online.
If this is the first time you are configuring the camera or if it is the first time after
resetting the camera to its factory defaults, DNA automatically authenticates
the camera with the default password for the camera's admin user (admin).
If the admin user password has been changed, authenticate the camera.
In the DNA Discover List, right-click the camera and select Login.
In the DNA - Login window, type the password for the admin user. If you do
not know the admin user password, contact the person who configured the
camera's users and passwords.
Click Login, wait for Ok status to appear, and then click Close.
In the DNA Discover List, verify that the camera's status is Authenticated.
d. Change the camera’s IP address.
Right-click the camera and select IP
Setup.
In the DNA - IP Setup window, clear
Use DHCP and specify the camera's IP
address. You can also specify the Mask
(default: 255.255.255.0) and Gateway.
Then, click Update, wait for Ok
status to appear, and then click Close.
To configure the camera for networking using the camera’s web page:
a. Open the camera’s web page by double-clicking the camera in the DNA
Discover List or by typing the camera’s IP address in a web browser’s address

427-0200-01-10 Rev 120
June 2021
This document does not contain any export-controlled information.
bar. The camera's web page supports Google Chrome®and other popular web
browsers.
b. On the login screen, type admin
for the user name and the
password for the admin user
(default: admin).
c. When logging in to the camera for the first time or for the first time after
performing a factory default, specify a new password for the admin user.
Note
Use a strong password consisting of at least 12 characters and
at least one uppercase letter, one lowercase letter, and one
number. Passwords can include the following special
characters: |@#~!$&<>+_-.,*?= .
Log back in with the new password.
The camera's View Settings Home Page opens.
d. Click System Settings.
Make sure the Network page appears.

427-0200-01-10 Rev 120
June 2021
This document does not contain any export-controlled information.
e. You can select Static and manually specify
the camera's Hostname, IP address,
Netmask, and Gateway. You can also
specify the DNS Mode, Name Servers,
MTU (maximum transmission unit), and
Ethernet Speed.
f. Click Save. If you have made any changes on the Network page, the camera
reboots.
Note
For more information about configuring the camera for networking,
see the camera’s installation and user guide.
4.2 Attach the Camera to a Supported VMS
After you have mounted the camera and discovered or defined its IP address, use
VMS Discovery/Attach procedures to attach the camera to a supported VMS.

427-0200-01-10 Rev 120
June 2021
This document does not contain any export-controlled information.
5 Camera Dimensions
Following are the Saros PTZ DM-Series camera’s dimensions.
Front View
Side View
6 Register the Product
Register your Product with Teledyne FLIR at https://customer.flir.com.
For warranty information, see https://www.teledyneflir.com/support-
center/warranty/security/flir-security-product-warranties/.
7 Contact Information
Teledyne FLIR LLC
6769 Hollister Avenue
Goleta, CA 93117
USA
Support: https://support.flir.com/
Corporate Headquarters
27700 SW Parkway Ave.
Wilsonville, OR 97070
USA