TeleWell TW-EAV510 AC v2 User manual

TeleWell TW-EAV510
XDSL ROUTER
RELEASE 1.3
USER MANUAL

2
CONTENTS
Device Installation....................................................................................................................... 4
Power on Router ......................................................................................................................... 4
Factory Reset Button .................................................................................................................. 4
Network Connections.................................................................................................................. 5
Configuration............................................................................................................................... 5
Web-based Configuration Utility ................................................................................................. 6
Device Info .................................................................................................................................. 7
Summary..................................................................................................................................... 8
WAN............................................................................................................................................ 8
Statistics...................................................................................................................................... 9
Route ........................................................................................................................................ 12
ARP........................................................................................................................................... 12
DHCP........................................................................................................................................ 12
Quick Setup .............................................................................................................................. 12
Advanced Setup........................................................................................................................ 13
Layer2 Interface ........................................................................................................................ 13
WAN Service............................................................................................................................. 17
LAN ........................................................................................................................................... 21
Ethernet Port............................................................................................................................. 23
NAT........................................................................................................................................... 23
Security ..................................................................................................................................... 26
Parental Control ........................................................................................................................ 29
3G ............................................................................................................................................. 31
Quality of Service...................................................................................................................... 33
Routing...................................................................................................................................... 35
DNS .......................................................................................................................................... 37
DSL ........................................................................................................................................... 40
UPNP ........................................................................................................................................ 41
DNS Proxy ................................................................................................................................ 41
DLNA ........................................................................................................................................ 42
Storage service ......................................................................................................................... 42
Interface Grouping .................................................................................................................... 43
IP Tunnel................................................................................................................................... 44
IPSec ........................................................................................................................................ 45
Power Management.................................................................................................................. 46

3
Multicast.................................................................................................................................... 47
Wireless .................................................................................................................................... 48
Basic ......................................................................................................................................... 48
Security ..................................................................................................................................... 49
MAC Filter ................................................................................................................................. 50
Wireless Bridge......................................................................................................................... 51
Advanced .................................................................................................................................. 51
Station Info................................................................................................................................ 52
Diagnostics ............................................................................................................................... 53
Diagnostics ............................................................................................................................... 53
Fault Management .................................................................................................................... 53
Management ............................................................................................................................. 54
Settings ..................................................................................................................................... 54
System Log ............................................................................................................................... 55
Security Log .............................................................................................................................. 56
TR069 client.............................................................................................................................. 57
Internet Time............................................................................................................................. 57
Access Control.......................................................................................................................... 58
Reboot ...................................................................................................................................... 60
Tools ......................................................................................................................................... 60
Troubleshooting ........................................................................................................................ 61
Glossary.................................................................................................................................... 63

4
11
Device Installation
The TW-EAV510 connects two separate physical interfaces, an xDSL (WAN) and an Ethernet
(LAN) interface. Place the Router in a location where it can be connected to the various
devices as well as to a power source. The Router should not be located where it will be
exposed to moisture or excessive heat. Make sure the cables and power cord are placed
safely out of the way so they do not create a tripping hazard. As with any electrical appliance,
observe common sense safety procedures.
The Router can be placed on a shelf or desktop, ideally you should be able to see the LED
indicators on the front if you need to view them for troubleshooting.
Power on Router
The Router must be used with the power adapter included with the device.
1.Insert the DC Power Adapter cord into the power receptacle located on the rear panel of the
Router and plug the adapter into a suitable nearby power source.
2.Depress the Power button into the on position. You should see the Power LED indicator light
up and remain lit. The Status LED should light solid green and begin to blink after a few
seconds.
3.If the Ethernet port is connected to a working device, check the LAN LED indicators to make
sure the connection is valid. The Router will attempt to establish the xDSL connection, if the
xDSL line is connected and the Router is properly configured this should light up after several
seconds. If this is the first time installing the device, some settings may need to be changed
before the Router can establish a connection.
Factory Reset Button
The Router may be reset to the original factory default settings by using a ballpoint or paperclip
to gently push down the reset button in the following sequence:
1.Press and hold the reset button while the device is powered off.
2.Turn on the power.
3.Wait for 10 seconds and then release the reset button.
Remember that this will wipe out any settings stored in flash memory including user account
information and LAN IP settings. The device settings will be restored to the factory default IP
address 192.168.0.254 and the subnet mask is 255.255.255.0, the default management
Username is “admin” and the default Password is “admin.”

5
Network Connections
Connect xDSL Line
Use the xDSL cable included with the Router to connect it to a telephone wall socket or
receptacle. Plug one end of the cable into the xDSL port (RJ-11 receptacle) on the rear panel
of the Router and insert the other end into the RJ-11 wall socket. If you are using a low pass
filter device, follow the instructions included with the device or given to you by your service
provider. The xDSL connection represents the WAN interface, the connection to the Internet. It
is the physical link to the service provider’s network backbone and ultimately to the Internet.
Connect Router to Ethernet
The Router may be connected to a single computer or Ethernet device through the
10BASE-TX Ethernet port on the rear panel. Any connection to an Ethernet concentrating
device such as a switch or hub must operate at a speed of 10/100 Mbps only. When
connecting the Router to any Ethernet device that is capable of operating at speeds higher
than 10Mbps, be sure that the device has auto-negotiation (NWay) enabled for the connecting
port. Use standard twisted-pair cable with RJ-45 connectors. The RJ-45 port on the Router is a
crossed port (MDI-X). Follow standard Ethernet guidelines when deciding what type of cable to
use to make this connection. When connecting the Router directly to a PC or server use a
normal straight-through cable. You should use a crossed cable when connecting the Router to
a normal (MDI-X) port on a switch or hub. Use a normal straight-through cable when
connecting it to an uplink (MDI-II) port on a hub or switch. The rules governing Ethernet cable
lengths apply to the LAN to Router connection. Be sure that the cable connecting the LAN to
the Router does not exceed 100 meters.
Hub or Switch to Router Connection
Connect the Router to an uplink port (MDI-II) on an Ethernet hub or switch with a
straight-through cable. If you wish to reserve the uplink port on the switch or hub for another
device, connect to any on the other MDI-X ports (1x, 2x, etc.) with a crossed cable.
Computer to Router Connection
You can connect the Router directly to a 10/100BASE-TX Ethernet adapter card (NIC) installed
on a PC using the Ethernet cable provided.
Configuration
This section will show you how to configure your new Router using the web-based
configuration utility.

6
Web-based Configuration Utility
Connect to the Router
The default IP address for xDSL MODEM is: 192.168.0.254; The Subnet Mask is：
255.255.255.0. Users can configure xDSL MODEM through an Internet browser. xDSL
MODEM can be used as gateway and DNS server; users need to set the computer’s TCP/IP
protocol as follow:
1. Set the computer IP address at same segment of xDSL MODEM, such as set the IP
address of the network card to one of the “192.168.0.100”～“192.168.0.200”.
2. Set the computer’s gateway the same IP address as the xDSL Modem’s.
3. Set computer’s DNS server the same as xDSL Modem’s IP address or that of an effective
DNS server.
To access the configuration utility, open a web-browser such as Internet Explorer and enter the
IP address of the router (192.168.0.254).
Type “admin” for the User Name and “admin” in the Password field. If you get a Page Cannot
be Displayed error, please refer to the Troubleshooting section for assistance.

7
Device Info
To access the Device Info window, click either the Device Info or Summary button in the
Device Info directory. The following page opens:

8
Summary
To access the Router’s first Summary window, click the Summary button in the Device Info
directory.
This window displays the current status of your DSL connection, including the software version,
LAN IP address, and DNS server address.
WAN
To access the WAN Info window, click the WAN button in the Device Info directory.
This window displays the current status of your WAN connection.

9
Statistics
The Statistics menu contains statistical information about the LAN, WAN service, and Optical.
Select Statistics in the Device Info menu to open the Statistics submenu.
LAN
The LAN window displays the statistics for the information received and transmitted over the
LAN interface.
Click LAN in the Statistics submenu to open the LAN window;
WAN Service
The WAN window displays the statistics for the information received and transmitted over the
WAN interface.
Click WAN Service in the Statistics submenu to open the WAN window;

10
xTM
To access the Device Info – xTM window, click the xTM button in the Device Info directory.
This read-only window displays xTM info.
xDSL
To access the Device Info – XDSL window, click the xDSL button in the Device Info
directory.
This read-only window displays xDSL info.

11

12
Route
To access the Device Info – Route window, click the Route button in the Device Info
directory.
This read-only window displays routing info.
ARP
To access the Device Info – ARP window, click the ARP button in the Device Info directory.
This read-only window displays Address Resolution Protocol info.
DHCP
To access the Device Info – DHCP Leases window, click the DHCP button in the Device Info
directory.
This read-only window displays DHCP lease info.
Quick Setup
The Quick Setup will help you to configure the device eazily. If you want Automatic
Configuration, click the checkbox of Automatic Configuration. When you are finished, click
the Apply/Save button to save.

13
Advanced Setup
This chapter include the more advanced features used for network management and security
as well as administrative tools to manage the Router, view status and other information used to
examine performance and for troubleshooting.
Layer2 Interface
To access the DSL ATM Interface Configuration window, click the ATM Interface button in
the Layer2 Interface directory.
This window is used to configure the ATM interface. You can add and delete ATM interface on
this window.
If you are setting up the ATM interface for the first time, click the Add button.

14
ATM Interface
The ATM PVC Configuration window allows you to set up ATM PVC configuration. Enter
Virtual Path Identifier, and Virtual Channel Identifier. The VPI and VCI values should be
provided by your ISP. This window also allows you to select DSL Link Type, PPPoA、IPoA and
EoA (EoA is for PPPoE, IPoE, and Bridge)
Use the drop-down menu to select the desired Encapsulation Mode.
Click the Apply / Save button to save.

15
VDSL2 (ptm) interface
The VDSL2 (ptm) interface Configuration window enables you to add, delete, or modify up to
one VDSL WAN Layer 2 interface connections.
Click VDSL2 (ptm) Interface in the Layer2 Interface menu to open the VDSL(ptm) WAN
Interface Configuration window
VDSL WAN Configuration
If you have selected to add or modify a VDSL interface connection, the VDSL WAN
Configuration window opens. Click the Apply/Save button to save.

16
ETH interface
The ETH WAN Interface Configuration window enables you to add, delete, or modify up to one
ETH WAN Layer 2 interface connections.
Click ETH Interface in the Layer2 Interface menu to open the ETH WAN Interface
Configuration window
ETH WAN Configuration
If you have selected to add or modify an ETH interface connection, the ETH WAN
Configuration window opens

17
WAN Service
To access the Wide Area Network (WAN) Service Setup window, click the WAN Service
button in the Advanced Setup directory.
This window is used to configure the WAN interface. You can add and delete WAN interface
on this window.
If you are setting up the WAN interface for the first time, click the Add button.
The WAN Service Interface Configuration Configuration window allows select a layer 2
interface for this service. Click the Next button to continue
This window allows you to select the appropriate connection type. The choices include PPP
over ATM (PPPoA), PPP over Ethernet (PPPoE), IP over Ethernet (IPoE), IP over ATM (IPoA),
and Bridging.
WAN Service Configuration – PPPoE
Click the PPP over Ethernet (PPPoE) radio button on this window. This window also allows
you to use the drop-down menu to enable IPv6 service. Click the Next button to continue.

18
WAN Service Configuration – PPPoE
This window allows you to set the username and the password for your PPP connection. This
information is obtained from your ISP. Additional settings on this window will also depend on
your ISP. And you can input 2nd IP on this page. Click the Next button to continue.

19
WAN Service Configuration – IPoE
This window allows you to configure the WAN IP settings. This information is obtained from
your ISP. Click the Next button to continue

20
WAN Service Configuration – Bridging
Click the Bridge radio button on this window. Click the Next button to continue.