Teltonika MVC100 User manual

4
Step 5 Access camera WEB interface
To access camera WEB interface first the PPP connection must be established. After successful
connection open the Web browser, type the camera IP address (http://10.0.0.1) and enter the administrator
login details:
The default administrator login settings are:
Login: admin
Password: admin
The welcome page of the WEB management interface after successful login to the camera is displayed.
From this menu all essential configuration pages are accessed.
The camera is now ready for configuration. Further details for setting camera features please refer to
user’s manual. Manual can be downloaded from Teltonika WEB page www.teltonika.eu.
LEGAL NOICE
Copyright © 2008 TELTONIKA Ltd. All rights reserved. Reproduction, transfer, distribution or
storage of part or all of the contents in this document in any form without the prior written permission of
TELTONIKA Ltd is prohibited.
Other product and company names mentioned herein may be trademarks or trade names of their
respective owners.
TELTONIKA
EDGE Camera (MVC100)
Quick Start guide v1.00
PACKAGE CONTENTS CHECKLIST
MVC100 EDGE Camera
External GSM antenna
AC/DC Power adapter (Euro or UK)
USB cable
Angled wall mount bracket
Leaflet “Quick Start Guide”

2 3
Back panel
Figure 1. EDGE camera back panel view.
1. Power supply adapter socket.
2. Battery
3. 5-pin terminal block
4. 5-pin terminal block for connecting external light
5. USB socket
6. LEDs (Not installed)
7. MicroSD card socket (Not installed)
8. GSM antenna connector
Step 1 Insert SIM card
Open and remove the back panel of the camera. To do that, use the screw-driver to loosen four screws
holding panel. After the back panel is removed gently insert the SIM card as showed in figures below.
Note: The manufacturer does not supply the SIM card, which is mandatory for setting up a
connection to the GSM network! The SIM card may be purchased from your GSM (mobile) service
provider!
Step 2 Attach antenna
Screw the antenna in a clockwise
direction. Position the antenna upwards
at its connecting joint. This will ensure
optimal reception.
Step 3 Install USB drivers (Windows)
1. Connect the AC/DC power adapter to the camera
2. Connect camera to the USB port.
3. Install FTDI drivers.
4. Open System in Control Panel: Start => Settings => Control Panel => System.
5. In the Hardware tab select Device Manager.
6. Expand Ports (COM & LPT), to find out USB Serial Port COM number. This number will be
used during the PPP connection configuration.
Note: Detailed information on driver installation for Windows XP can be found at www.ftdichip.com,
application note: “FTDI Drivers Installation guide for Windows XP” (AN_104).
Step 4 Set PPP connection (Windows)
1. Connect the AC/DC power adapter to the camera and
2. Connect camera to the PC USB port.
3. Open Network connections in Control Panel:
Start => Settings => Control Panel => Network connections
4. Choose File => New connection. In the New Connection Wizard window click Next.
5. Select Set up an advanced connection click Next. Select Connect directly to another
computer and click Next.
6. Select Guest, click Next.
7. Enter the connection name and click Next.
8. Select COM port which was created by camera (refer to Quick Start Guide Step 3).
9. You may select Add a shortcut to this connection to my desktop to have a connection shortcut
on the desktop.
10. Click Finish to end connection wizard.
11. In the connect window select Properties to customize connection.
12. In General tab press Configure. In the new appeared Modem configuration window define
Maximum speed (bps) to 115200 bps. Then uncheck Enable hardware flow control option.
Click OK to close modem configuration properties.
13. In Networking tab scroll down to Internet Protocol (TCP/IP) and press Properties. Press
Advanced and uncheck Use default gateway on remote network. Click OK on all opened
configuration windows.
14. Connection is now configured and ready to run. Press Connect to establish PPP connection. After
the connection is established, the network icon appears in the Windows system tray. The icon
indicates link speed and activity.