Texas Instruments Adpater User manual

DockMate
User’s Guide
9794528-0001, Rev. A
Printed in U.S.A.

Copyright (©) 1995 Texas Instruments Incorporated
All Rights Reserved — Printed in U.S.A.
DockMate User’s Guide
TI Part No. 9794528-0001, Rev. A
Original Issue: August 1995
Changes may be made periodically to the information in
this publication. Such changes will be incorporated in new
editions of this manual.
No part of this publication may be reproduced, stored in a
retrieval system, or transmitted, in any form or by any
means, electronic, mechanical, photocopy, recording, or
otherwise, without the prior written permission of Texas
Instruments Incorporated.
TravelMate and DockMate are trademarks of Texas Instruments.
The icons in the Windows Notebook and Startup groups are copyrighted by Texas
Instruments.
PS/2 is a registered trademark and VGA is a trademark of International Business
Machines Corporation.
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft
Corporation.

FCC Statement
Class B Digital Device. This equipment has been tested
and found to comply with the limits for a Class B digital
device pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
❏Reorient or relocate the receiving antenna
❏Increase the separation between the equipment and
the receiver
❏Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected
❏Consult the Dealer or an experienced radio/television
technician for help.
Notice: Canadian Users
This Class B digital apparatus meets all requirements of
the Canadian Interference-Causing Equipment Regulations.
Remarque à l’intention des utilisateurs
canadiens
Cet appareil numérique de la classe B respecte toutes les
exigences du Règlement sur le matériel brouilleur du
Canada.

Notice: Shielded Cables
All connections to other computing devices must be made
using shielded cables to maintain compliance with FCC
regulations.
c
Caution: Changes or modifications not expressly
approved by Texas Instruments could void the user’s
authority, which is granted by the Federal
Communications Commission, to operate this
equipment.

Contents
Preface
Chapter 1 Features
Chapter 2 DockMate Installation
Unpacking Instructions............................................ 2-2
DockMate Software Installation................................ 2-3
DockMate Hardware Installation .............................. 2-4
Chapter 3 Utilities
Introduction............................................................. 3-2
Using TI Setup ......................................................... 3-3
Using the SetDock Utility ......................................... 3-5
Chapter 4 Troubleshooting Procedures
Notebook Connection ............................................... 4-2
Option Installation ................................................... 4-3
PCMCIA Card Recognition........................................ 4-5
Appendix A Reference Material
Appendix B DockMate Specifications
Index
Contents
Contents v

Preface
Introduction
This document discusses the Texas Instruments
DockMateSystem. This system is a low-cost, multi-port
adapter for use with the TravelMate5000 Series notebook
computers. When used with the notebook computer,
external keyboard, mouse, and VGAmonitor (not
supplied with the system), the DockMate System turns
your notebook into an ergonomic desktop workstation.
This manual tells you how to install, operate, and maintain
your DockMate.
nNote: Also review the Quick Start document (TI Part No.
9786164-0001) prior to using your system for the first time.
This manual contains four chapters and two appendixes
including:
❏Chapter 1: Features — Introduces the main features
of your new DockMate.
❏Chapter 2: DockMate Installation — Describes how
to unpack your system, install software, dock, and
connect all external devices (keyboard, VGA monitor,
external mouse, etc.).
❏Chapter 3: Utilities —Customizes your desktop for
use with a docking system.
❏Chapter 4: Troubleshooting Procedures — Provides
operator-level troubleshooting procedures for solving
problems that you may encounter when configuring
and using the system.
Preface 1

Preface
❏Appendix A: Reference Material — Provides a list of
related documentation.
❏Appendix B: DockMate Specifications — Provides a
list of system specifications for your DockMate.
Ordering Parts and Supplies
To order TI publications, option kits, spare parts, or
supplies for your system, contact 1-800-TI-TEXAS or the
Texas Instruments service center for your country.
Preface
2 Preface

1
Features
Your Expansion System provides hardware and software
expansion capabilities to TravelMate 5000 notebook
computers. Using DockMate, your notebook is effectively
turned into a desktop workstation with minimal
configuration.
This Chapter Provides:
❏A general overview of the system features
DockMate provides true VGA pass-through connectivity.
Ports are configured using the SetDock Utility discussed in
Chapter 3 of this document. The following table provides
information about features of DockMate:
Feature Description
25-Pin Parallel Port Connects to a parallel printer or other
device that uses a standard parallel
interface. EPP/ECP compatible.
9-Pin Serial Port Connects to external devices such as a
serial printer. 16550 UART.
PS/2 Ports (two) Connects to PS/2 keyboard,external
numeric keypad, or mouse.
15-Pin VGA Port Connects to an external VGA monitor
Features 1-1

Features
Your DockMate includes the following features:
PS/2
VGA
Parallel
Serial
Power PS/2
Features
1-2 Features

2
DockMate Installation
This Chapter Explains:
❏How to unpack and inventory the system components
❏Software installation
❏Hardware installation
nNote: After completion of the hardware installation, you
must configure TI Setup or SetDock programs as described
in Chapter 3 of this manual.
Contents
Unpacking Instructions ...........................................2-2
DockMate Software Installation...............................2-3
DockMate Hardware Installation..............................2-5
Docking the Notebook .............................................. 2-5
Installing an External PS/2 Option .......................... 2-6
Serial Port Connections............................................ 2-6
Parallel Port Connections ......................................... 2-7
Video Connector....................................................... 2-7
AC Connection ......................................................... 2-7
DockMate Installation 2-1

UnpackingInstructions
The DockMate is shipped with the following hardware
components:
❏DockMate
❏DockMate User’s Guide (this manual)
❏Accessory Kit
Unpack the DockMate using the following instructions:
1. Carefully cut the tape that seals the top flap of the
shipping carton.
2. Remove the DockMate and all accessories from the
shipping carton.
3. Remove all protective coverings from the DockMate
and accessories, and inventory the contents. Save
shipping container and packaging if shipping is
required in the future.
Unpacking Instructions
2-2 DockMate Installation

DockMateSoftwareInstallation
A DockMate System Installation diskette is provided with
your DockMate. Software on this diskette updates the
TravelMate BIOS software with the latest version that
supports your DockMate. If your TravelMate has a newer
version of BIOS than the one on the diskette, the program
will not change the BIOS on your system.
For your TM5000 Series computer to work correctly with
the DockMate, you must upgrade the BIOS (Basic
Input/Output System) with new firmware (FLASH ROM).
To upgrade the BIOS, complete the following steps:
1. Turn off power to your notebook computer.
2. Ensure the system is undocked.
3. Place the DockMate Installation diskette into drive A.
4. Turn on power to your notebook computer.
5. Follow instructions on the screen.
n
Note: If your system BIOS is more current than the BIOS
on the diskette, your system BIOS is not updated and you
are taken to the MS-DOS®prompt. If this is the case,
remove the diskette and reboot.
6. When finished, remove the floppy disk and slide the
power switch off then on to boot.
7. During the boot process you will hear a beep.
Immediately press Ctrl-Alt-Esc.
8. If you have previously changed the configuration of TI
Setup for special hardware requirements, note the
settings before continuing to the next step. Reload
them later as required by your hardware.
9. From the Setup menu, press Esc-F5 to load factory
defaults.
DockMate Software Installation
DockMate Installation 2-3

10. Press Esc-F4 to save the configuration.
The installation process is complete and your computer
reboots.
n
Note: When using a DockMate, plug the AC adapter
supplied with your TravelMate 5000 into the DockMate. All
power on or off is then controlled by the notebook’s power
switch.
n
Note: Some TM5000 Series notebooks may experience
PCMCIA recognition problems when docked to a DockMate.
Troubleshooting procedures are located in Chapter 4,
Troubleshooting Procedures.
DockMate Software Installation
2-4 DockMate Installation

DockMateHardwareInstallation
Docking the Notebook
Use the following procedure to dock your notebook
computer:
1. Clear an area on your workstation surface to permit
both units to be flat on the table or desktop while
performing the initial docking procedure.
2. Ensure that the rear port covers on the TM5000 are
open.
3. Lift the lever on top of the DockMate so that the guide
pin plate is extended.
4. Carefully match the holes on the underside of the
notebook with the guide pins protruding from the
DockMate and press down on the top lever to dock.
nNote: To undock the noteboook, lift up the lever and lift
the notebook off the docking pegs.
Inserting the notebook
DockMate Hardware Installation
DockMate Installation 2-5

Installing an External PS/2®Option
The DockMate allows you to attach any of the following to
the 6-pin PS/2 connectors on the system:
❏external keyboard (side port recommended)
❏external PS/2 mouse (rear port recommended)
❏external numeric keypad (rear or side port)
To install the external PS/2 option, connect a round PS/2
connector cable to the 6-pin circular connector on the rear
or side of the system.
Serial Port Connections
Your DockMate is equipped with a 9-pin serial port with
16550 UART that can be attached to any external serial
device such as:
❏external modem
❏serial printer
❏any device that uses an RS-232 interface
When using the Serial Port connection on the DockMate,
the Serial Port connector on the notebook is disabled.
cCaution: Never connect a parallel device to a serial
port, or a serial device to a parallel port or video port;
this may cause damage to the DockMate. If you are
uncertain as to what type connector the external
device has, refer to the technical manual for the
external device.
DockMate Hardware Installation
2-6 DockMate Installation

Parallel Port Connections
Your DockMate is equipped with one DB25 (25-pin)
bidirectional parallel port (device name LPT1). This port
occupies address 0378h, and is designated as LPT1
(default value). Typically, the notebook computer sends
print data to LPT1 unless the menu is configured otherwise.
When using the Parallel Port connection on the DockMate,
the Parallel Port connector on the notebook is disabled.
Video Connector
To install an external VGA monitor (optional), connect the
VGA cable connector to the 15-pin connector on the rear of
the DockMate. The DockMate supports all external
monitors supported by the TM5000. For further
information, refer to the TravelMate 5000 User’s Guide.
nNote: Refer to the TravelMate 5000 User’s Guide and User’s
Reference Guide for information on VGA utilities.
AC Connection
Your DockMate must run off of AC power by connecting a
TI AC adapter (TI Part No. 9786094-0003) to the system.
DockMate is designed to be powered by an AC adapter that
is attached to either the connected notebook or to the
DockMate (power transfers through the expansion bus
pins).
cCaution: Only a TM5000 AC adapter, TI Part No.
9786094-0003, can be connected to a DockMate.
DockMate Hardware Installation
DockMate Installation 2-7

3
Utilities
This chapter tells you about:
❏Using DockMate utilities
Contents
Introduction ....................................................... 3-2
Using TI Setup .................................................... 3-3
Using the SetDock Utility.................................... 3-5
Running SetDock .................................................3-5
SetDock Key Functions ........................................3-6
Exiting SetDock....................................................3-7
Utilities 3-1

Introduction
TI provides two utilities that are copied to your system
when you install software from the DockMate System
Installation diskette:
❏TI Setup - for use with Windows 95 and Windows for
Workgroups
❏SetDock - for use with MS-DOS
These utilities allow advanced users to configure special
operating modes or parameters for hardware attached to
the TravelMate notebook or the DockMate.
Introduction
3-2 Utilities

UsingTISetup
TI Setup is copied onto your system at the time you install
the DockMate Installation diskette. TI Setup is used to
configure peripheral hardware attached through your
DockMate. TI Setup is used in either Windows or Windows
95 environments.
To configure peripherals for use with your system, complete
the following steps:
1. Complete the following for your operating system:
❏If you are using Windows 95 - Double-click on TI
Setup in the Control Panel
❏If you are using Windows for Workgroups -
Double-click on TI Setup in the TravelMate
Notebook Center group
2. Select the tab labeled Ports-Dock A.
3. Under Dock Type, use the pulldown menu (by selecting
the ▼) and single-click on DockMate.
4. Using configuration information provided with your
peripheral device, change any required settings in this
window.
n
Note: A Ports-Dock B tab (identical to the Ports-Dock A
tab) is provided in case you have more than one type of
DockMate system and want to maintain settings for both
types. If both Ports Dock A and B are set to the same type
of DockMate system, only Ports Dock A settings are used.
The Ports - Undocked tab indicates settings for your
TravelMate notebook when undocked from the DockMate.
Using TI Setup
Utilities 3-3

The following table provides a synopsis of all options
available on the Ports-Dock A or Ports-Dock B tabs:
Item Options Description
Dock Type None (default)
DockMate
DockMate Plus
DockMate Net Ready
DockMate
General Pn’P Dock
Allows you to select the
type of docking station
attached to your notebook.
General Pn’P Dock provides
auto setup for any
operating system that
supports true Plug ’N Play.
Dock 9 Pin Off
COM1 (default)
COM2
COM3
COM4
Allows you to disable or set
the port address used for
the notebook or docking
system serial port.
Notebook SIR Off
COM1 (default)
COM2
COM3
COM4
Allows you to disable or set
the port address used for
the docking system serial
infrared port.
Dock SIR Off
COM1 (default)
COM2
COM3
COM4
Allows you to disable or set
the port address used for
the docking system port.
COM3/COM4 338h/238h
3e8h/2e8h (default)
2e8/2e0
Allows you to select the
address at which COM
ports 3 and 4 operate.
Dock Parallel Port Address Off
3BCh
378h (default)
278h
Allows you to select the
address at which the
parallel port operates.
Dock Parallel Port
Extended Mode
Off (default)
SPP
EPP and SPP
ECP
ECP and EPP
Allows you to select the
protocol for bidirectional
operation (printers or
parallel network adapters).
Using TI Setup
3-4 Utilities