Texas Instruments HDC2080EVM User manual

HDC2080EVM User 's Guide
User's Guide
Literature Number: SNAU197
April 2018

2SNAU197–April 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
HDC2080EVM User 's Guide
User's Guide
SNAU197–April 2018
HDC2080EVM User 's Guide
1 Introduction
The Texas Instruments HDC2080EVM evaluation module (EVM) enables designers to evaluate the
operation and performance of the HDC2080 Relative Humidity and Temperature Sensor.
The EVM contains one HDC2080 (See Table 1).
Table 1. Device and Package Configurations
DEVICE IC PACKAGE
U1 HDC2080DMBR PWSON (6-pin) DMB
The EVM hosts an MSP430F5528 microcontroller (µC) as well as the HDC2080. The µC is used to control
the HDC2080 and communicate with a host PC through a USB port. The EVM is designed to be broken
into two sections if desired. The sensor section can be separated from the µC section so that the user can
remotely locate the sensor from the µC section.
2 Setup
This section describes the connectors on the EVM as well and how to properly connect, setup and use the
HDC2080EVM.
Figure 1. HDC2080EVM

www.ti.com Setup
3
SNAU197–April 2018
Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated
HDC2080EVM User 's Guide
2.1 Input/Output Connector Description
2.1.1 J1 – 5x1 Header
This header is not populated and can be installed if the EVM is broken in 2 sections: PC interface and
Sensor. This connector with its counterpart J2 allows the communication of the two sections through a 5-
wire cable
J1.1 GND
J1.2 SDA
J1.3 SCL
J1.4 INT
J1.5 VDD
2.1.2 J2 – 5x1 Header
This header is not populated and can be installed if the EVM is broken in 2 sections: PC interface and
Sensor. This connector with its counterpart J1 allows the communication of the two sections through a 5-
wire cable.
J2.1 GND
J2.2 SDA
J2.3 SCL
J2.4 INT
J2.5 VDD
2.1.3 USB Type A Connector
This connector is used for communications with the PC and provides power for the EVM.
2.2 Hardware Setup
The HDC2080EVM power is supplied via the USB connector. The LDO (U4) converts the 5V from the
USB to 3.3V used by the HDC2080 and the MSP430. The EVM may be directly inserted into a USB port
on a PC or laptop, or may be connected to the latter using the appropriate USB cable.
The I2C address of the HDC2080 is set at EVM level at 1000000xb on the EVM. The I2C address has
been set mounting the 0 Ωresistor R12 (refer to Figure 2).

Setup www.ti.com
4SNAU197–April 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
HDC2080EVM User 's Guide
Figure 2. HDC2080EVM : Sensor Module
To change the I2C address, remove the resistor R12 and populate the R4 with 0 Ωresistor (refer to
Figure 3 )

www.ti.com Setup
5
SNAU197–April 2018
Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated
HDC2080EVM User 's Guide
Figure 3. HDC2080EVM: Layout Resistors for I2C Address Setting - Top
Table 2. I2C Address
ADDR R12 R4 HDC2080 ADDRESS
0 Short Open 1000000
1 Open Short 1000001
In Table 2, the EVM default configuration is in bold.

Setup www.ti.com
6SNAU197–April 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
HDC2080EVM User 's Guide
2.3 Software Setup
2.3.1 System Requirements
The Sensing Solutions GUI supports:
• 64-bit Windows 7
• 64-bit Windows XP
The current GUI does not support 32-bit Windows operating systems. The host machine is required for
device configuration and data streaming. The following steps are necessary to prepare the EVM for the
GUI:
• The GUI and EVM driver must be installed on the host.
• The EVM must be connected to a full speed USB port (USB 1.0 or above).
2.3.2 Sensing Solutions GUI and EVM Driver Installation
The Sensing Solutions GUI and EVM driver installer is packaged in a zip file. Follow these steps to install
the software.
1. Download the software ZIP file from the EVM tool page
2. Extract the downloaded ZIP file
3. Run the included executable
4. Follow all directions from the installer
Figure 4. GUI Installer Welcome Page

www.ti.com Setup
7
SNAU197–April 2018
Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated
HDC2080EVM User 's Guide
5. Read the license agreement and if you still wish to install the software, select “I accept the agreement”
and click “Next” as shown in
Figure 5. GUI Installer License Agreement
6. Select the installation directory. If the user installing the software is not a system administrator a
directory not with “Program Files” must be chosen instead of the default.
Figure 6. GUI Installer Installation Directory

Setup www.ti.com
8SNAU197–April 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
HDC2080EVM User 's Guide
7. Wait for all files to install
Figure 7. GUI Installer Copying Files
8. After the files have copied a device driver installer will start. If prompted about an unsigned driver,
choose to install the driver anyways. If running Windows 8 or 8.1, the PC must be started in a “Safe”
mode to install the unsigned driver.
Figure 8. EVM Driver Installer Welcome Page

www.ti.com Setup
9
SNAU197–April 2018
Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated
HDC2080EVM User 's Guide
9. Wait for the driver to install
Figure 9. EVM Driver Installer In Progress
10. Click “Finish” after the driver has been installed
Figure 10. EVM Driver Installer Complete

Setup www.ti.com
10 SNAU197–April 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
HDC2080EVM User 's Guide
11. Click “Finish” to complete the software installation
Figure 11. GUI Installer Complete
2.4 Operation
When the EVM is connected, the host computer will automatically detect the device and
Launch the GUI. A detailed description of the GUI operation is presented later in this document.