Texas Instruments TPL5010EVM User manual

User's Guide
SNAU173–January 2015
TPL5010 Evaluation Module
This user's guide provides the setup instructions, configuration, and operation of the TPL5010 evaluation
module (EVM). Also included are the printed-circuit board (PCB) layouts, schematic, and the bill of
materials (BOM).
Contents
1 Introduction ................................................................................................................... 2
2 Setup .......................................................................................................................... 3
2.1 Jumpers and Connectors.......................................................................................... 3
2.2 Battery Requirements .............................................................................................. 5
2.3 TPL5010EVM Configuration....................................................................................... 5
3 Operation.................................................................................................................... 11
3.1 Supply Current Measurement ................................................................................... 11
4 Board Layout................................................................................................................ 14
5 Schematic ................................................................................................................... 16
6 Bill of Materials ............................................................................................................. 17
List of Figures
1 TPL5010EVM ................................................................................................................ 2
2 J1 Jumper Setting ........................................................................................................... 3
3 J1 Jumper Setting ........................................................................................................... 3
4 J2 Jumper Setting ........................................................................................................... 4
5 I_SEL Jumper Setting....................................................................................................... 4
6 R_SEL Jumper Setting...................................................................................................... 4
7 Jumpers Configuration – EVM Standalone Without Microcontroller .................................................. 6
8 Jumpers Configuration – EVM With Microcontroller .................................................................... 7
9 Jumpers Configuration – EVM With LaunchPad ........................................................................ 8
10 Current Measurement Setup – TPL5010 Only ......................................................................... 11
11 Current Measurement Setup – TPL5010 During the Reading of the Resistance.................................. 12
12 Current Measurement Setup – TPL5010 With Microcontroller....................................................... 13
13 Top Layer.................................................................................................................... 14
14 Bottom Layer................................................................................................................ 15
15 TPL5010EVM Schematic.................................................................................................. 16
List of Tables
1 Device and Package Configurations ...................................................................................... 2
2 Input/Output Connectors Description...................................................................................... 3
3 Jumpers Description......................................................................................................... 3
4 Switches and Selectors Description....................................................................................... 4
5 Test Points Description ..................................................................................................... 4
6 TPL5010EVM Bill of Materials ........................................................................................... 17
LaunchPad is a trademark of Texas Instruments.
DURACELL is a registered trademark of The Gillette Company.
1
SNAU173–January 2015 TPL5010 Evaluation Module
Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated

R_SEL REXT
J1
I_SEL
MANUAL_DRV DONE
U1
REXT1
REXT2
J2
IO
Q1
Q2
J1/J3 J4/J2
Introduction www.ti.com
1 Introduction
Figure 1. TPL5010EVM
TI's TPL5010EVM evaluation module (EVM) allows a designer to configure the timer intervals of the
TPL5010 and measure its very low current consumption. Moreover, the TPL5010EVM is ready to be
connected to the LaunchPad™ of the MSP430F5529 in order to test its watchdog and timer features. The
EVM has an onboard battery holder (coin battery) to supply the TPL5010 and the microcontroller, if
connected.
The EVM contains one TPL5010 (see Table 1).
Table 1. Device and Package Configurations
Device IC Package
U1 TPL5010DDC SOT23-6
2TPL5010 Evaluation Module SNAU173–January 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated

WAKE
Connected
to Q2
J1 J1
Q2 OFF WAKE Connected
to IO
J1
RSTn
Connected
to Q1
J1 J1
Q1 OFF RSTn Connected
to IO
J1
www.ti.com Setup
2 Setup
Section 2.1 describes the jumpers and connectors on the EVM and Section 2.3 describes how to properly
connect, set up, and use the TPL5010EVM.
See Figure 1 for locations of the top layer jumpers and switches.
2.1 Jumpers and Connectors
Table 2 through Table 5 list the input/output connectors description, jumpers description, switches and
selectors description, and the test points description.
Table 2. Input/Output Connectors Description
Name Layer Description
J1/J3 Bottom 2 × 10 pin receptacle to plug the TPL5010EVM into the MSP430F5529 LaunchPad
J4/J2 Bottom 2 × 10 pin receptacle to plug the TPL5010EVM into the MSP430F5529 LaunchPad
RST Bottom 2-pin receptacle to plug the TPL5010EVM into the MSP430F5529 LaunchPad
VCC Bottom 2-pin receptacle to plug the TPL5010EVM into the MSP430F5529 LaunchPad
IO Top 4-pin header connector to bring out RSTn, WAKE, DONE, and GND signals
IO.1 GND Ground
IO.2 DONE DONE signal from external microcontroller
IO.3 WAKE WAKE signal to external microcontroller
IO.4 RSTn RSTn signal to external microcontroller
Table 3. Jumpers Description
Name Layer Description
J1 Top J1.5–J1.3 shorted, the RSTn pin of the TPL5010 is connected to the gate of Q1 MOSFET.
J1.3–J1.1 shorted, the gate of Q1 MOSFET is connected to VDD (MOSFET OFF).
Figure 2. J1 Jumper Setting
J1.6–J1.4 shorted, the WAKE pin of the TPL5010 is connected to the gate of Q2 MOSFET.
J1.4–J1.2 shorted, the gate of Q2 MOSFET is connected to VDD (MOSFET OFF).
Figure 3. J1 Jumper Setting
3
SNAU173–January 2015 TPL5010 Evaluation Module
Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated

R_SEL Fix
Resistance
R_SEL
Variable
Resistance
Normal
Operation
I_SEL
TPL5010 Current
Measurement
I_SEL
DONE
Connected
to S2
J2 DONE
Connected
to IO
J2
Setup www.ti.com
Table 3. Jumpers Description (continued)
Name Layer Description
J2 Top In short configuration, the DONE pin of the TPL5010 is connected to the S2 switch with a pull-down
resistor.
Figure 4. J2 Jumper Setting
I_SEL Top In open configuration allows the measurement of the current consumption of the TPL5010.
Figure 5. I_SEL Jumper Setting
R_SEL Top Pin1-2 in short configuration, the variable resistance is used to set the timer interval.
Pin2-3 in short configuration, the fix resistance is used to set the timer interval.
Figure 6. R_SEL Jumper Setting
Table 4. Switches and Selectors Description
Name Layer Description
S_ON_OFF Bottom In ON position turns ON the EVM, in OFF position turns OFF the EVM
S1 Top When pushed, the SPST switch generates a DONE pulse
S2 Top When pushed, the SPDT ON/Momentary switch generates a Manual
reset pulse
Table 5. Test Points Description
Name Layer Description
GND Top Test point of the ground, connect the GND of the power supplies
V_BATT Top Test point to monitor battery voltage
AUX_VDD Top Test point to connect external supply voltage in alternative to the coin
cell battery
4TPL5010 Evaluation Module SNAU173–January 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated

www.ti.com Setup
2.2 Battery Requirements
In case the EVM is battery powered, the battery must meet the following requirements:
• Battery type: CR2032 UL-certified battery
• Voltage: 3 V
• Minimum capacity: 220 mAh
• Minimum discharge rate: N/A mA
NOTE: Only insert DURACELL®2032 Lithium battery type CR2032, or equivalent.
2.3 TPL5010EVM Configuration
The evaluation board can work standalone or plugged into the MSP430F5529 LaunchPad.
2.3.1 Setting the Time Interval Period
Set the Time interval period by tuning the variable resistance (the trimmer can generate resistances in the
range between 1 kΩand 200 kΩ).
To tune the value of the resistance:
1. Connect a DMM between pin 1 of R_SEL and GND.
2. Turn the screw on the top of the trimmer until you reach the desired value.
3. Disconnect the DMM at the end of the operation.
Alternatively, set the DRV pulse interval with the fix resistances (R_EXT1 = 500 Ω, R_EXT2 = 0 Ω). If
required, replace the resistances with customized ones.
See Figure 1 for locations of the resistances REXT1 and REXT2.
5
SNAU173–January 2015 TPL5010 Evaluation Module
Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated

S_ON_OFF
I_SEL
J1
J2
R_SEL
CR2032
IO
DONE
WAKE
xx
xx
xx
xx
xx
x
x
xx
xx
xx
Setup www.ti.com
2.3.2 EVM Standalone Without Microcontroller
The following settings are provided to use the EVM standalone, without a microcontroller:
• Put the S_ON_OFF selector in the OFF position.
• Set the mode of operation through the MODE header (see Table 3).
• Insert a CR2032 coin cell battery in the battery holder (BT), alternatively, connect a voltage source
between the AUX_VDD and GND test points.
• Configure jumper J1 (RSTn connected to Q1, WAKE connected to Q2) and J2 (DONE connected to
S2), as explained in Table 3.
NOTE: Do not connect the coin cell battery and the voltage source to supply the evaluation board at
same time.
• Put the S_ON_OFF selector in the ON position, or turn on the external voltage source if it is used
instead of the coin cell battery.
The DONE and WAKE signals can be monitored at the IO connector (pin 2 and 3, respectively).
Figure 7. Jumpers Configuration – EVM Standalone Without Microcontroller
6TPL5010 Evaluation Module SNAU173–January 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated

S_ON_OFF
I_SEL
J1
J2
R_SEL
CR2032
VDD
RSTGPIOGPIOGND
µC
IO
DONE
WAKE
GND
RSTn
www.ti.com Setup
2.3.3 EVM With Microcontroller
The following settings are provided to use the EVM with a microcontroller:
• Put the S_ON_OFF selector in the OFF position.
• Set the mode of operation through the MODE header (see Table 3).
• Connect the microcontroller to the IO header in order to manage the I/O signal of the design under test
(DUT).
• Supply the microcontroller, connecting its supply pin to the AUX_VDD test point and the ground to the
GND pin of the IO header.
• Insert a CR2032 coin cell battery in the battery holder (BT), alternatively, connect a voltage source
between the AUX_VDD and GND test points.
• Configure the jumper J1 (RSTn connected to IO, WAKE connected to IO) and J2 (DONE connected to
IO), as explained in Table 3.
NOTE: Do not connect the coin cell battery and the voltage source to supply the evaluation board at
same time.
Do not use the switch S2 (DONE), in this configuration the DONE switch is connected to a
digital output pin of the microcontroller.
• Put the S_ON_OFF selector in the ON position, or turn on the external voltage source if it is used
instead of the coin cell battery.
Figure 8. Jumpers Configuration – EVM With Microcontroller
7
SNAU173–January 2015 TPL5010 Evaluation Module
Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated

S_ON_OFF
I_SEL
J1
J2
R_SEL
RST VCC
J4/J2
J1/J3
CR2032
Setup www.ti.com
2.3.4 EVM With LaunchPad
Load the code from this section into the MSP430F5529 of the LaunchPad. Refer to MSP430 LaunchPad
(MSP-EXP430F5529) Wiki for more details.
• Put the S_ON_OFF selector in the OFF position.
• Set the mode of operation through the MODE header (see Table 3).
• Remove jumpers VCC and RST of the LaunchPad.
• Plug the EVM into the LaunchPad (MSP430F5529), according to the following table:
TPL5010EVM MSP430 LaunchPad
J1/J3 J1.1 VDD_µC J1/J3 pin 1 3V3
pin 4 GND pin 4 GND
J4/J2 pin 2 GND J4/J2 pin 2 GND
pin 4 WAKE pin 4 P2.0
pin 10 RSTn pin 10 RST
pin 18 DONE pin 18 P2.3
VCC 3V3
RST SBW RST
• Insert a CR2032 coin cell battery in the battery holder (BT), alternatively, connect a voltage source
between the AUX_VDD and GND test points.
• Configure the jumper J1 (RSTn connected to Q1, WAKE connected to Q2) and J2 (DONE connected
to IO), as explained in Table 3.
NOTE: Do not connect the coin cell battery and the voltage source to supply the evaluation board at
the same time.
Do not use the switch S2 (DONE), in this configuration, the DONE switch is connected to a
digital output pin of the microcontroller.
• Put the S_ON_OFF selector in ON position, or turn on the external voltage source if it is used instead
of the coin cell battery.
Figure 9. Jumpers Configuration – EVM With LaunchPad
8TPL5010 Evaluation Module SNAU173–January 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated

www.ti.com Setup
Example code
Once loaded into the MSP430 of the LaunchPad, the code presented in this section performs the following
features:
• At power on, the green LED present on the LaunchPad is turned on and turned off.
• When the MSP430 receives a RSTn, the red LED is toggled 5 times, then the green LED is turned ON
and OFF and the MSP430 sends a DONE signal to the TPL5010.
• When the MSP430 receives a WAKE pulse, the green LED is turned ON and OFF and the MSP430
sends a DONE signal to the TPL5010.
#include <msp430.h>
void main(void) {
WDTCTL = WDTPW | WDTHOLD; // Stop watchdog timer
P1DIR |= BIT0; // Set P1.0 to output direction
P2DIR |= BIT3; // Set P2.3 to output direction
P4DIR |= BIT7; // Set P4.7 to output direction
P1OUT &= ~BIT0; // Set P1.0 RED LED OFF
P2OUT &= ~BIT3; // Set P2.3 DONE Low
P4OUT &= ~BIT7; // Set P4.7 GREEN LED OFF
P2IES &= ~BIT0; // P2.0 Lo/Hi edge
P2IFG &= ~BIT0; // P2.0 IFG Cleared
P2IE |= BIT0; // P2.0 Interrupt Enabled
SFRRPCR |= SYSNMIIES | SYSNMI; // Select NMI function for the RST/NMI pin,
// interrupt on falling edge
// (pull-up R on RST/NMI is already enabled after PUC)
SFRIE1 |= NMIIE; // Set NMI pin interrupt enable
P4OUT |= BIT7; // Set P4.7 GREEN LED ON
__delay_cycles(500000); // Set Delay
P4OUT &= ~BIT7; // Set P4.7 GREEN LED OFF
P2OUT |= BIT3; // Done High
__delay_cycles(100); // Set Delay
P2OUT &= ~BIT3; // Done Low
__bis_SR_register(LPM4_bits + GIE); // Enter LPM4
}
// Port 2 interrupt service routine
#pragma vector=PORT2_VECTOR
__interrupt void Port_2(void)
{
volatile unsigned int i;
P4OUT |= BIT7; // GREEN LED ON
i = 10000; // SW Delay
do i--;
while(i != 0);
P4OUT &= ~BIT7; // Set P4.7 GREEN LED OFF
P2OUT |= BIT3; // Done High
__delay_cycles(100); // Set Delay
P2OUT &= ~BIT3; // Done Low
P2IES &= ~BIT0; // P2.0 Lo/Hi edge
P2IFG &= ~BIT0; // P2.0 IFG Cleared
P2IE |= BIT0; // P2.0 Interrupt Enabled
9
SNAU173–January 2015 TPL5010 Evaluation Module
Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated

Setup www.ti.com
}
// User NMI interrupt service routine
#pragma vector=UNMI_VECTOR
__interrupt void UNMI_ISR (void)
{int n=0;
// Efficiently decode the User NMI interrupt source
switch (__even_in_range(SYSUNIV, SYSUNIV_SYSBUSIV)) {
case SYSUNIV_NMIIFG :
{for(n=0; n<10; n++) {
volatile unsigned int i;
P1OUT ^= 0x01; // Toggle RED led
i = 10000; // SW Delay
do i--;
while(i != 0);
}
volatile unsigned int i;
P4OUT |= BIT7; // GREEN LED ON
i = 10000; // SW Delay
do i--;
while(i != 0);
P4OUT &= ~BIT7; // Set P4.7 GREEN LED OFF
P2OUT |= BIT3; // Done High
__delay_cycles(100); // Set Delay;
P2OUT &= ~BIT3; // Done Low;
}break;
case SYSUNIV_OFIFG :
case SYSUNIV_ACCVIFG :
case SYSUNIV_BUSIFG :
default :
break;
}
}
10 TPL5010 Evaluation Module SNAU173–January 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated

\
nA DMM
S_ON_OFF
I_SEL
J1
J2
R_SEL
IO
CR2032
www.ti.com Operation
3 Operation
Once the EVM is powered ON, the TPL5010 starts working. Refer to the TPL5010 datasheet (SNAS651)
for further details on the timing:
• Configure the trimmer equal to 5 kΩto set a time interval of 1 s.
• When an RSTn pulse is generated by the TPL5010, the red LED (D2) is turned on. The green LED
(D1) is turned on when a WAKE signal is generated by the TPL5010.
• If the DONE switch (S2) is pushed, a DONE pulse is sent to the TPL5010. If the DONE pulse is sent
within the programmed time interval, at the next cycle the green LED (D1) is turned ON.
• When the M_RST switch (S1) is pushed, a manual reset pulse is sent to the TPL5010. For both DONE
and M_RST pulses, the width of the pulse is proportional to the pressure time. While the M_RST
switch is pressed the red LED turns ON.
3.1 Supply Current Measurement
3.1.1 Supply Current Measurement of the TPL5010 Only
First, turn off the EVM (ON/OFF switch to OFF position), then disconnect the EVM from the LaunchPad or
microcontroller, in order to not load the digital output pins of the DUT.
• Leave the I_SEL jumper open.
•Do not leave digital input pins floating; Short the DONE pin (second pin of IO header) to GND (first
pin of IO header), turn OFF the Q1 and Q2 MOSFET (as explained in Table 3).
• Connect a digital multimeter, configured as the current meter (able to measure nA), between
AUX_VDD and pin 1 of I_SEL.
• Turn on the EVM (ON/OFF switch to ON position).
• Read the current consumption on the DMM.
Figure 10. Current Measurement Setup – TPL5010 Only
11
SNAU173–January 2015 TPL5010 Evaluation Module
Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated

\
nA DMM
S_ON_OFF
I_SEL
J1
J2
R_SEL
IO
CR2032
MANUAL RESET
Operation www.ti.com
3.1.2 Supply Current Measurement of the TPL5010 During the Reading of the Resistance
First, turn off the EVM (ON/OFF switch to OFF position), then disconnect the EVM from the LaunchPad or
your microcontroller, in order to not load the digital output pins of the DUT.
• Leave the I_SEL jumper open.
•Do not leave digital input pins floating; Short the DONE pin (second pin of IO header) to GND (first
pin of IO header), turn OFF the Q1 and Q2 MOSFET (as explained in Table 3).
• Connect a digital multimeter, configured as the current meter (able to measure nA), between
AUX_VDD and pin 1 of I_SEL.
• Keep the MANUAL_RST switch pressed while turning ON the EVM.
• Turn on the EVM (ON/OFF switch to ON position).
• Read the current consumption on the DMM.
Figure 11. Current Measurement Setup – TPL5010 During the Reading of the Resistance
12 TPL5010 Evaluation Module SNAU173–January 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated

\
nA DMM
S_ON_OFF
I_SEL
J1
J2
R_SEL
CR2032
VDD
RSTGPIOGPIOGND
µC
IO
www.ti.com Operation
3.1.3 Supply Current Measurement of the TPL5010 With Microcontroller
First, turn off the EVM (ON/OFF switch to OFF position):
• Load the code into the microcontroller.
• Connect the microcontroller to the EVM, refer to Section 2.3.3.
• Install the I_SEL jumper.
•Do not leave digital input pins floating; Ensure that the DONE signal is controlled by the
microprocessor, turn OFF the Q1 and Q2 MOSFET (as explained in Table 3).
• Connect a digital multimeter, configured as the current meter (able to measure nA), between V_BATT
test point and AUX_VDD test point.
• Leave the EVM OFF (ON/OFF switch to OFF position).
• Read the current consumption on the DMM while pressing the MANUAL_RESET switch.
Figure 12. Current Measurement Setup – TPL5010 With Microcontroller
13
SNAU173–January 2015 TPL5010 Evaluation Module
Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated

Board Layout www.ti.com
4 Board Layout
Figure 13 and Figure 14 illustrate the TPL5010EVM board layouts.
Figure 13. Top Layer
14 TPL5010 Evaluation Module SNAU173–January 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated

www.ti.com Board Layout
Figure 14. Bottom Layer
15
SNAU173–January 2015 TPL5010 Evaluation Module
Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated

GND
GND
J1.2
J1.3
J1.4
J1.5
J1.6
J1.7
J1.8
J1.9
J1.10
+5V
J3.3
J3.4
J3.5
J3.6
J3.7
J3.8
J3.9
J3.10
J4.2
J4.3
J4.4
J4.5
J4.6
J4.7
J4.8
J4.9
J4.10
J2.3
J2.4
J2.6
J2.7
J2.8
J2.10
J4.1
GND
GND
GND
VDD
I_SEL shorted, TPL5010 supplied by battery/external
supply
I_SEL open, current consumption measured with
DMM placed between pin 1 and 2 of I_SEL.
BT
SH-J2
VDD
GND
GND
GND
1
2
3
R_SEL
R_SEL 3-2 shorted, R_EXT set by trimmer.
R_SEL 1-2 shorted R_EXT set by fix resistors
1
2
I_SEL
SH-J1
0.1µF
C1
GND
3
1
2
4
5
6
S1
PVB4 OA 300 NS LFS
Green
1
2
D1
3
1
2
-50V
Q1
AUX_VDD
AUX_VDD
GND
Super Red
1
2
D2
301
R4
1
23
Q2
301
R5
AUX_VDD
GND
0
REXT_2
1
2
3
4
S2
4-1437565-1
AUX_VDD
Female headers to connect the TPL5010EVM to the launchpad MSP430F5529
1
2
RST
1
2
VCC
Female headers to disconnect the PowerSupply and
RST signal of the micro present on the launchpad
4
1
2
3
IO
WAKE
DONE
GND
200k ohm
TRIM
FID2
FID1
FID3
SV601108
B
PCB Number:
PCB Rev:
LOGO
PCB
Texas Instruments
V_BATT
AUX_VDD
AUX_VDD
VDD
1
GND
2
DELAY/M_RST
3
DONE 4
WAKE 5
RST 6
U1
TPL5010DDC
499
REXT_1
100k
RP
AUX_VDD
5
4
6
73
1
2
S_ON_OFF
EG1257
SH-J5
SH-J4
SH-J3
AUX_VDD
Assembly Note
ZZ2
Place shunt SH-J2 on R_SEL
Assembly Note
ZZ3
Place shunt SH-J3 on J1, 3-5
Assembly Note
ZZ1
Place shunt SH-J1 on I_SEL
Assembly Note
ZZ4
Place shunt SH-J4 on J1, 4-6
Assembly Note
ZZ5
Place shunt SH-J5 on J2, 1-2
1
3
56
4
2
7
910
8
12
11
14
13
16
15
18
17
20
19
J1/J3
66953-010LF
1
3
56
4
2
7
910
8
12
11
14
13
16
15
18
17
20
19
J4/J2
66953-010LF
RSTn
WAKE
DONE
100k
RD
GND
WAKE
RSTn
DONE
AUX_VDD
GND
0.1µF
C2
RSTn
1
2
3
4
5
6
J1
AUX_VDD
GND
1
2
J2
Schematic www.ti.com
5 Schematic
Figure 15 illustrates the TPL5010EVM schematic.
Figure 15. TPL5010EVM Schematic
16 TPL5010 Evaluation Module SNAU173–January 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated

www.ti.com Bill of Materials
6 Bill of Materials
Table 6 lists the TPL5010EVM BOM.
Table 6. TPL5010EVM Bill of Materials
Designator Description Manufacturer Part Number Quantity
AUX_VDD Test Point, TH, Miniature, Red Keystone 5000 1
BT Battery Holder, CR2032, Retainer clip, TH Memory Protection Devices BS-7 1
C1, C2 CAP, CERM, 0.1uF, 6.3V, +/-10%, X5R, 0402 TDK C1005X5R0J104K 2
D1 LED, Green, SMD OSRAM LG L29K-G2J1-24-Z 1
D2 LED, Super Red, SMD Lumex SML-LX0603SRW-TR 1
GND Test Point, TH, Miniature, Black Keystone 5001 1
IO Header, 100mil, 4x1, Gold, TH Samtec TSW-104-07-G-S 1
I_SEL Header, TH, 100mil, 2x1, Gold plated, 230 mil above insulator Samtec TSW-102-07-G-S 1
J1 Header, 50mil, 3x2, Gold, TH Sullins Connector Solutions GRPB032VWVN-RC 1
J2 Header, 50mil, 2x1, Gold, TH Sullins Connector Solutions GRPB021VWVN-RC 1
J1/J3, J4/J2 Receptacle, 100mil, 10X2, TH FCI 66953-010LF 2
Q1 MOSFET, P-CH, -50V, -0.13A, SOT-323 Diodes Inc. BSS84W-7-F 1
Q2 MOSFET, N-CH, 50V, 0.2A, SOT-323 Diodes Inc. BSS138W-7-F 1
R4, R5 RES, 301 ohm, 1%, 0.1W, 0603 Vishay-Dale CRCW0603301RFKEA 2
REXT_1 RES, 499 ohm, 0.1%, 0.1W, 0603 Susumu Co Ltd RG1608P-4990-B-T5 1
REXT_2 RES, 0 ohm, 5%, 0.1W, 0603 Vishay-Dale CRCW06030000Z0EA 1
RD, RP RES, 100k ohm, 5%, 0.063W, 0402 Vishay-Dale CRCW0402100KJNED 2
RST, VCC Connector, Receptacle, 100mil, 2x1, Gold plated, TH TE Connectivity 5-534206-1 2
R_SEL Header, TH, 100mil, 3x1, Gold plated, 230 mil above insulator Samtec, Inc. TSW-103-07-G-S 1
S1 Switch, Pushbutton, SPDT, 0.1A 14V C&K Components PVB4 OA 300 NS LFS 1
S2 Switch, Tactile, SPST-NO, 0.05A, 12V, SMT TE Connectivity 4-1437565-1 1
SH-J1, SH-J2 Shunt, 100mil, Gold plated, Black 3M 969102-0000-DA 2
SH-J3, SH-J4, SH- Mini Shunt, Closed Top, 650 V AC, -45 to 85°C, Pitch 1.27 mm, Sullins Connector Solutions NPB02SVAN-RC 3
J5 Height 3 mm, RoHS
S_ON_OFF Switch, Slide, SPDT, 0.3A, SMT E-Switch EG1257 1
TRIM TRIMMER, 200K, 0.25W, SMD Bourns 3224W-1-204E 1
U1 Ultra-Low Power System Timer with Watchdog functionality and Texas Instruments TPL5010DDC 1
Manual Reset, DDC0006A
V_BATT Test Point, Miniature, White, TH Keystone 5002 1
17
SNAU173–January 2015 TPL5010 Evaluation Module
Submit Documentation Feedback Copyright © 2015, Texas Instruments Incorporated

STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES
1. Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or
documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.
Acceptance of the EVM is expressly subject to the following terms and conditions.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software
License Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment
by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any
way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or
instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as
mandated by government requirements. TI does not test all parameters of each EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,
or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the
warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to
repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall
be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3Regulatory Notices:
3.1 United States
3.1.1 Notice applicable to EVMs not FCC-Approved:
This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit
to determine whether to incorporate such items in a finished product and software developers to write software applications for
use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless
all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause
harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is
designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of
an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2 For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER

FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1 For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1 Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2 Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of
Japan to follow the instructions below with respect to EVMs:
1. Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
2. Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
3. Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
SPACER
SPACER
SPACER
SPACER
SPACER

【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
2. 実験局の免許を取得後ご使用いただく。
3. 技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ
い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER
4EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1 User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2 EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5. Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER