Textron Jacobsen Ransomes Parkway 3 Meteor LGNN344 Guide

RJL 100 June 2016
Safety, Operation & Maintenance Manual
Veiligheids-, bedienings- en onderhoudsinstructies
Ransomes Parkway 3 Meteor™ met ROPS, Kubota V1505-T
With ROPS Series / Met ROPS - Reeksen: JX
Product code / Productcode: LGNN344
Ransomes Parkway 3 Meteor™ met cabine, Kubota V1505-T
With Cab Series / Met cabine - Reeksen: JY
Product code / Productcode: LGNN345
WARNING
WARNING: If incorrectly used this machine can cause severe injury.
Those who use and maintain this machine must be trained in its
proper use, warned of its dangers and must read the entire manual
before attempting to set up, operate, adjust or service the machine.
WAARSCHUWING
WAARSCHUWING: Bij onjuist gebruik kan deze machine
ernstig letsel veroorzaken. Degenen, die deze machine
gebruiken en onderhouden, moeten getraind zijn in de juiste
bediening, gewezen zijn op de gevaren en dienen de gehele
bedieningshandleiding te hebben gelezen, alvorens pogingen
te ondernemen de machine in te stellen, te bedienen, af te
stellen of onderhoud aan de machine te plegen.
25039G-NL (Rev.3)
NL
Netherlands

1 CONTENTS
© Ransomes Jacobsen Limited. All Rights Reserved
SECTION PAGE
2 INTRODUCTION
Important.........................................................................................3
Product Identification .....................................................................4
Guidelines For The Disposal Of Scrap Products ...........................6
During Service Life ........................................................................6
End Of Service Life ........................................................................6
Parts Manual ..................................................................................7
Key Numbers .................................................................................7
Notes .............................................................................................8
3 SAFETY
How To Operate Safely ..................................................................9
Safe Operation ...............................................................................9
Preparation ....................................................................................9
Operation ......................................................................................10
ROPS ............................................................................................11
Safe Handling Of Fuels .................................................................11
Maintenance And Storage ............................................................11
When You Put The Mower On A Trailer .......................................12
Important Safety Notes .................................................................13
4 SPECIFICATION
Engine Specification .....................................................................16
Machine Specification ...................................................................17
Dimensions & Weights Meteor Flail .............................................18
Dimensions & Weights With Magna 250 And Sport200 ...............20
Hydraulic Specification With Meteor Flail .....................................22
Hydraulic Specification With Magna 250 Or Sport 200 .................22
Vibration Level With Meteor Flail ..................................................23
Vibration Level With Magna 250 Or Sport 200 .............................24
Noise Level ...................................................................................25
Slopes ...........................................................................................25
Cutting Unit Specification Magna 20 Sport 200 ...........................26
Cutting Performance .....................................................................26
Recommended Lubricants ............................................................26
Accessories ..................................................................................26
Certificates Of Conformity..............................................................27
Notes ............................................................................................33
5 DECALS
Safety Decals EC ..........................................................................34
Instruction Decals EC ...................................................................36
6 CONTROLS
Operator Workstation ....................................................................38
Instrument Panel (With ROPS Fitted) ...........................................39
Instrument Panel (With Cab Fitted) ..............................................40
Cab Controls .................................................................................41
Visual Display ...............................................................................44
Start Up Screen ............................................................................44
Warning/service Screen ................................................................44
Start Up Slope Warning Screen.....................................................45
Main Run Screen ..........................................................................46
Water Temperature Screen ..........................................................47
Blocked Charge Filter Screen .......................................................47
Slope Warning Screens .................................................................48
Main Menu ....................................................................................49
Clock & Date Adjust ......................................................................49
Service Menu ................................................................................50
Data logging Menu ........................................................................51
Language Menu ............................................................................51
Accessory Power Outlet (With Cab Fitted) ...................................54
Traction Pedal ...............................................................................54
Steering Tilt Control ......................................................................54
Horn ..............................................................................................55
Accessory Power Outlet ...............................................................55
Parking Brake Release Valve .......................................................55
Free Wheel ...................................................................................56
Lighting Kit (Optional) ...................................................................57
Seat Right Hand Arm Rest & Pod .................................................57
7 OPERATION
Daily Inspection ............................................................................58
Operator Presence And Safety Interlock System .........................59
Operating Procedure ....................................................................60
Fitting Cutting Units To The Machine ...........................................61
Backlapping ..................................................................................61
Backlapping Procedure (Sport 200 And Magna 250 Only) ...........62
Operation Of The Machine ...........................................................63
Before Operating For The First Time ............................................63
Starting The Engine ......................................................................63
Driving ...........................................................................................64
Mowing .........................................................................................64
To Stop The Engine ......................................................................65
Unblocking Cutting Units ..............................................................65
Transporting ..................................................................................65
Transporting On A Trailer Or Flatbed ...........................................66
Mowing On Slopes ........................................................................67
Slope Calculation Chart ................................................................69
8 MAINTENANCE
Maintenance & Lubrication Charts ............................................... 70
Engine Lubrication ........................................................................ 74
Engine: Fan Belt ........................................................................... 75
Engine Coolant ............................................................................. 76
Hydraulic System .......................................................................... 77
Hydraulic Test Ports ..................................................................... 78
Fuel System .................................................................................. 79
Air Cleaner .................................................................................... 80
Battery .......................................................................................... 81
Jump Start Cable (Option) ............................................................ 82
Machine Maintenance .................................................................. 82
Lubrication Meteor Flail Unit ......................................................... 83
Lubrication Of Magna 250 & Sport 200 Cutting Unit .................... 83
Flail Paddle Blade Maintenance ................................................... 84
Flail Half “y” Blade Maintenance ................................................... 84
Check Flail Shaft Bearings ........................................................... 85
Hydraulic Motor Drive Shaft .......................................................... 85
9 ADJUSTMENTS
Traction Control Pedal .................................................................. 86
Weight Transfer Adjustment ......................................................... 86
Flail Unit Height Of Cut Adjustment .............................................. 87
Cutting Unit Height Of Cut Adjustment ......................................... 88
Floating Head Front Roll Setting (Sport 200) ................................ 88
Cutting Cylinder To Bottom Blade Adjustment ............................. 89
Cutting Cylinder Bearings ............................................................. 90
Front And Rear Roll Bearings ....................................................... 90
Grass Deflector ............................................................................. 90
General Instructions For Grammer Seats ..................................... 91
Seat (Grammer MSG85) .............................................................. 92
Air Suspension Seat (Grammer MSG75 -521) ............................. 93
Weight Adjustment ....................................................................... 93
Fore/aft Adjustment ...................................................................... 93
Backrest Extension ....................................................................... 94
Seat Heater ................................................................................... 94
Lumbar Support ............................................................................ 94
Armrests ........................................................................................ 95
Armrest Adjustment ...................................................................... 95
Backrest Adjustment ..................................................................... 95
Maintenance ................................................................................. 96
Notes ............................................................................................ 97
10 ACCESSORIES
Rotary Beacon Kit ......................................................................... 98
Light & Mirror Kit ........................................................................... 98
Storage Rack Kit ........................................................................... 99
TST Kit ......................................................................................... 99
Mow / Transport Switch Kit .......................................................... 100
Jump Start Kit .............................................................................. 100
11 P
ROBLEM S OLVING
Problem Solving Engine .............................................................. 101
12 QUALITY OF CUT
Quality Of Cut Problem Solving ................................................... 102
Washboarding ............................................................................. 102
Marcelling .................................................................................... 103
Step Cutting ................................................................................. 104
Scalping ....................................................................................... 105
Stragglers .................................................................................... 106
Streaks ......................................................................................... 107
Windrowing .................................................................................. 108
Mismatched Cutting Units ............................................................ 109
Torn Crowns ................................................................................ 110
Laying Uncut Grass ..................................................................... 111
Tramlining .................................................................................... 112
13 FUSES AND RELAYS
Fuse And Relay Identification....................................................... 114
14 GUARANTEE
Warranty ...................................................................................... 116
Service ........................................................................................ 116
SECTION PAGE

en-3
INTRODUCTION 2
2.1 IMPORTANT __________________________________________________________
The Ransomes Parkway 3 Meteor is a Diesel engined is a self propelled Reel / Flail mower. The hydraulic
systems are for the traction drive, the cutting unit lift and the lower and cutting unit drives and steering.
IMPORTANT: Do the maintenance indicated in this manual to make sure that the quality of cut is kept at a high
level.
This SAFETY AND OPERATORS MANUAL is part of the machine and must stay with the machine always.
Suppliers of both original and used machines need to keep the documentation that comes with the machine.
You must use the machine to cut the grass only and not for any other purpose. Compliance with the conditions of
operation, service and repair specified by the manufacturer, are understood to be part of the correct use.
ALL operators MUST read through this manual and understand the Safety Instructions, controls, lubrication and
maintenance procedures.
Make sure that you obey all safety and road traffic regulations.
You must not make any changes to the machine that the manufacturer does not approve. This type of change
can release the manufacturer from the liability for any damage or injury.
Discard worn parts, taking note of the environmental result, use the systems available in the country where the
machine is used. When the machine is at its end of life, there are guidelines in this manual for the removal of the
machine from use.
Use only Ransomes Jacobsen Genuine spare parts to make sure that European conformity is controlled.
2006/42/EC
These instructions are the Original instructions confirmed by Ransomes Jacobsen Limited

en-4
2 INTRODUCTION
MADE IN JAPAN
V1505
Serial No.:
Code No.:
XXXXXXX
XXXXX-XXXXX
MADE IN JAPAN
V1505
Serial No.:
Code No.:
XXXXXXX
XXXXX-XXXXX
2.2 PRODUCT IDENTIFICATION ___________________________________________
A Maximum front axle load in Kg (for machines being driven
on the highway)
B Gross weight (mass) in Kg
C Maximum rear axle load in Kg (for machines being driven on
the highway)
D Power in Kw
E Date code
F Machine type (Designation)
G Product code
H Product name
J Serial number
Location of Serial number plate
The serial number plate (A) is found on the chassis under the position for the
operator seat.
Chassis Stamp
The Serial number and date code (B) are marked on the chassis under the
seat plate
Engine Identification
Serial Plate
Location of Serial number plate
The engine serial number is found on the top of the valve cover toward the
front of the mower. Label shows the engine group and serial number.
The engine serial number is also found on the engine block.
Kg Kw Kg Kg
West Road
Ransomes Europark
Ipswich IP3 9TT
England
ABCD E
FG
HJ
HH000301
ABCD
HH000301
ABCD
A
Kg Kw Kg Kg
WestRoad
RansomesEuropark
IpswichIP39TT
England
ABCDE
FG
HJ
LWA
10505 d B
A

en-5
INTRODUCTION 2
CD
E
Kg
A
F
West Road
Ransomes Europark
Ipswich IP3 9TT
England
B
ROPS Serial Plate
A Weight of ROPS
B Date Code
C Standard Used
D Part Number
E Used on Product
F Serial Number
ROPS Serial Plate Location
The ROPS serial plate (C) is located at the base of the front of the ROPS
main beam.
C

en-6
2 INTRODUCTION
2.3GUIDELINES FOR THE DISPOSAL OF SCRAP PRODUCTS _____________________
2.3.1 DURING SERVICE LIFE _______________________________________________
Used oil, oil filters and engine coolant are hazardous materials. Recommended procedures must be followed for their
safe removal.
If a fluid leaks, contain the spill to make sure that the leak does not flow into the ground or drainage system. Follow the
local laws to make sure that leaks are controlled safely.
The maintenance procedures in this manual make sure that the damage that the machine can cause in the local
environment is controlled safely.
When the machine completes its full service life, the following actions must be taken.
2.3.2 END OF SERVICE LIFE _______________________________________________
These guidelines must be used with applicable Health, Safety and Environmental laws. Always use the approved local
waste disposal and agencies for recycled materials.
• Park the machine in a location to use all of the necessary lifting equipment.
• Use correct tools and Personal Protective Equipment (PPE) and take instruction from the technical
manuals applicable to the machine.
• Remove and store correctly
1. Batteries
2. Fuel
3. Engine coolant
4. Oils
• Disassemble the structure of the machine and refer to the technical manuals where applicable. Give
attention to parts that have mechanical pressure or tension applied to the part in the machine, including
springs.
• Items that continue to have a service life must be separated and returned to the local store.
• Items that are worn must be separated into the material groups and removed according to the agencies
for recycled materials that are available. Common types are as follows:
• Steel
• Non ferrous metals
• Aluminium
• Brass
• Copper
• Plastic materials
• Identified
• Can be recycled
• Can not be recycled
• Not identified
• Rubber
• Electrical and Electronic Components
• If an item is not easily separated into different material groups, the material must be added to the
“General discarded materials” area.
• Do not burn discarded materials.
Change the machinery records to show that the machine is not in service and is discarded. Supply this serial number to
Ransomes Jacobsen Warranty Department to close their records.

en-7
INTRODUCTION 2
2.4 PARTS MANUAL ______________________________________________________
In compliance with the ISO14001 standard, Ransomes Jacobsen Limited does not send a paper parts manual
with every product.
To refer to a parts list for this mower you have four options:
1. Website – www.Ransomes Jacobsen.com. Select the “GENUINE PARTS” tab followed by the
“ONLINE PARTS LOOK-UP” tab. You now have access to Parts drawings and lists to help with the
identification of spare parts.
2. Website – www.rRansomes Jacobsen.com. Select the “SUPPORT” tab. You now have access to a PDF
version of the parts manual.
3. Complete the form included in the technical manual pack supplied with the machine for one of the two
options below
a. A disc that contains an electronic copy of the Parts Book.
b. A paper copy of the parts manual.
2.5 KEY NUMBERS _______________________________________________________
Record the key numbers shown below:
Starter Switch:-- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Diesel tank:-- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Record the machine and engine numbers shown below:
The machine serial number is found on the registration plate and the engine serial number can be found on the
rocker cover.
Machine Number:- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Engine Number:- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

en-8
2 INTRODUCTION
NOTES

en-9
SAFETY 3
3.1 HOW TO OPERATE SAFELY ___________________________________________________
3.1.1 Safe Operation
a Read the Operator’s Manual and other training material. If the operator or technician can not read this
manual, the owner is responsible to describe this material to the operators and technicians. Manuals in
additional languages may be available on the Jacobsen or RansomesJacobsen website.
a Read all of the instructions for this mower carefully. Know the controls and the correct operation of the
equipment.
b Children or persons who do not understand these instructions must not use the mower. The local
regulations can limit the age of the operator.
c Never use a mower near persons, including children or animals.
d Remember that the operator or owner is responsible for accidents or hazards that occur to other persons or
their property.
e Never carry passengers.
f Never allow persons to operate or service the mower or its attachments without correct instructions.
g Do not operate equipment while tired, sick or after you use alcohol or drugs.
3.1.2 Preparation
a When you operate the mower, wear correct clothing, slip resistant work shoes or boots, work gloves, hard
hat, safety glasses and hearing protection. Long hair, loose clothing or jewelry can be caught in moving
parts.
b Do not operate the equipment with the Interlock System disconnected or the system does not operate
correctly. Do not disconnect or prevent the operation of any switch.
c Never operate equipment that is not in correct order or without decals, guards, shields, deflectors or other
protective devices fastened. When you mow with a side discharge deck, DO NOT operate the cutting unit
without the discharge chute installed.
d Inspect the mower before you operate the mower. Check the tire pressure, engine oil level, the radiator
coolant level and the air cleaner indicator. Fuel is flammable. Use caution when you add the fuel to the
mower.
e Operate the mower in daylight or in good artificial light. Use caution when you operate the mower during
bad weather. Never operate the mower with lightning in the area.
f Inspect the area to select the accessories and attachments that are needed to correctly and safely do the
job. Only use parts, accessories and attachments approved by Jacobsen.
g Be careful of holes in the terrain and other hazards that are not visible.
h Inspect the area where the equipment is operated. Remove all objects you can find before you operate. Be
careful of obstructions above the ground (low tree limbs, electrical wires) and also underground obstacles
(sprinklers, pipes, tree roots). Enter a new area carefully. Look for possible hazards.
i Inspect the cutting system before you start the mower. Make sure the blades are free to rotate. When you
rotate one blade, other blades can rotate.
WARNING
EQUIPMENT OPERATED INCORRECTLY OR WITHOUT TRAINING CAN BE DANGEROUS.
Know the location and correct operation of controls. Operators without experience must receive instruction from
another person that knows the correct operation of the equipment before you operate the mower.
Only use parts, accessories and attachments approved by Jacobsen.
!

en-10
3 SAFETY
3.1.3 Operation
a Never operate the engine without enough ventilation or in an enclosed area. The carbon monoxide in the
exhaust fumes can increase to dangerous levels.
b Never carry passengers. Keep other persons or animals away from the mower.
c Disengage all drives and engage the parking brake before you start the engine. Only start the engine with
the operator in the seat. Never start the engine with persons near the mower.
d Keep your legs, arms and body inside the operator compartment while the mower is in operation. Keep
your hands and feet away from the cutting units.
e Do not use on the slopes greater than the safe slope limit for the equipment.
f To guard against over turning or loss of control:
– Operate the mower up and down on the face of slopes (vertically), but not across the face (horizontally).
– Do not start or stop suddenly on slopes.
– Decrease the speed when you operate on slopes or when you must turn. Use caution when you change
direction. Turf condition can change the mower stability.
– Use caution when you operate the mower near drop-offs, ditches or embankments.
– Be careful of holes in the terrain and other hazards that are not visible.
g When you drive in the reverse direction, look behind you and down to make sure the path is clear. Do not
operate the cutting units when you drive in the reverse direction.
h Use caution when you go near corners, trees or other objects that can prevent a clear view.
i Equipment must meet the current regulations to be driven on the public roads.
j Before you move across or operate on the paths or roads, turn off the PTO switch, lift the mowers and
travel at decreased speed. Look for traffic.
k Stop the blades when the mower is on any surface that is not grass.
l Do not release the cut grass in the direction of persons or allow persons near the mower while in operation.
m Do not operate the mower with damaged guards or without safety devices in position.
n Do not change the engine governor setting or over-speed the engine. Never change or tamper with
adjusters that are closed with a seal for the engine speed control.
o Before you leave the operator compartment, for any reason:
– Disengage all the drives and lower attachments to the ground.
– Engage the parking brake.
– Stop the engine and remove the key.
p When you hit an object or mower starts to cause the vibration that is not normal, inspect the mower for
damage and make repairs.
q Decrease the throttle setting before you stop the engine.
r Do not use this equipment for uses that the mower was not made for.

en-11
SAFETY 3
3.1.4 ROPS
a The ROPS is a safety device. Keep the ROPS in the vertical and locked position. Always use the seat belt
when you operate the mower. Make sure the seat belt can be released quickly in an emergency.
b Only operate the mower with the ROPS in the folded position on flat and level surfaces when necessary.
Do not operate the mower with the ROPS in the folded position on slopes, near sharp edges or near water.
There is no roll over protection with the ROPS in the folded position.
c Check for clearance before you drive below objects. Do not contact tree branches, electrical wires or other
objects with the ROPS.
d Do not use the seat belt with the ROPS in the folded position.
e Inspect the ROPS for damage. Keep the ROPS hardware fastened.
f Do not weld, drill, change or bend the ROPS. Replace a damaged ROPS. Do not try to correct a damaged
ROPS.
g Do not remove the ROPS from the mower.
h Jacobsen must approve any changes to the ROPS.
3.1.5 Safe Handling of Fuels
a The fuel and the fuel vapors are flammable. Use caution when you add the fuel to the mower. The fuel
vapors can cause an explosion.
b Never use the containers that are not approved to keep or transfer fuel.
c Never keep the mower or fuel containers near an open flame or any device that can cause the ignition of
fuel or fuel vapors.
d Never fill the fuel containers inside a vehicle or on a truck or trailer with a plastic liner. Always put the fuel
container on the ground away from your vehicle before you fill the container.
e Refuel the mower before you start the engine. When the engine is in operation or while the engine is hot,
never remove the fuel cap or add fuel to the mower.
f Refuel outdoors only and do not smoke when you add fuel. Extinguish all types of ignition.
g The fuel nozzle must touch the rim of the fuel tank when you add fuel to the mower. Do not use a device to
lock the fuel nozzle in the open position.
h Do not over fill the fuel tank. Leave at least 1 inch (25 mm) below the filler neck.
i Always tighten the fuel tank cap and container cap after you add fuel.
j If the fuel spills on your clothing, change your clothing immediately.
3.1.6 Maintenance and Storage
a Before you clean, adjust or repair this equipment, push PTO switch to the OFF position, lower the cutting
unit to the ground, engage the parking brake, stop the engine and remove the key.
b Make sure the mower is parked on a solid and level surface.
c Never work on a mower that is lifted only by the jack. Always use the jack stands.
d Never allow persons to service the mower or its attachments without correct instructions.
e When the mower is parked, put into storage or left without an operator, lower the cutting device unless a
positive mechanical lock is used.
When you put the mower on a trailer or put the mower in storage, close the fuel valve. Do not keep fuel near
flames or drain the fuel inside a building.
f Disconnect the battery before you service the mower. Always disconnect the negative battery cable before
the positive battery cable. Always connect the positive battery cable before the negative battery cable.

en-12
3 SAFETY
g Charge the battery in an area with good airflow. The battery can release hydrogen gas that is explosive. To
prevent an explosion, keep any device that can cause sparks or flames away from the battery.
h Disconnect the battery charger from the power supply before you connect or disconnect the battery charger
to the battery. Wear protective clothing and use insulated tools when you service the battery.
i Be careful and wear gloves when you check or service the cutting unit blades. Replace any damaged
blades, do not try to correct a damaged blade.
j Keep your hands and feet away from parts that move. Do not adjust the mower with the engine in
operation, unless the adjustment needs the engine in operation.
k Carefully release the pressure from components with stored energy.
l To prevent injury from the hot, high pressure oil, never use your hands to check for oil leaks. Use the paper
or cardboard to find leaks.
m The hydraulic fluid pressure can have enough force to enter your skin. If hydraulic fluid has entered your
skin, a doctor must remove the hydraulic fluid surgically within a few hours or gangrene can occur.
n When you service the hydraulic system, make sure the hydraulic fittings, tubes and hoses are tightened to
the correct torque. Make sure the hydraulic system is in good condition before you start the engine.
o Keep the mower and the engine clean.
p Allow the engine to become cool before storage and always remove the ignition key.
q Keep all nuts, bolts and screws tight to make sure the equipment is in safe condition.
r Replace worn or damaged parts for safety. Replace damaged or worn decals. Only use parts, accessories
and attachments approved by Jacobsen.
s To decrease the fire hazard, remove materials that burn from the engine, muffler, battery tray and fuel tank
area.
t Disconnect the battery and controller connectors before you weld on this mower.
3.1.7 When you Put the mower on a trailer
a Be careful when you load or unload the mower on a trailer. Trailer must be wider than the mower and can
carry the weight of the mower.
b Use a full-width ramp to load or unload the mower on a trailer.
c Use straps, chains, cables or ropes to fasten the mower to the trailer. Both front and rear straps must be
sent down and toward sides of trailer.
Make sure that all latches are correctly fastened.

en-13
SAFETY 3
3.1.8 Important Safety Notes
This safety alert symbol is used to alert you to possible hazards.
DANGER:
Indicates a dangerous condition that WILL cause death or injury unless it is prevented.
WARNING:
Indicates a dangerous condition that CAN cause death or injury unless it is prevented.
CAUTION:
Indicates a dangerous condition that can cause injury and property damage unless it is prevented. Also, the label
can indicate work procedures that are not safe.
IMPORTANT:
Only drive the machine at road speed when you are on a highway. You must not select road speed on grass
areas or rough roads and gravel tracks.
Some illustrations in this manual can show shields, guards or plates removed for clearness. This equipment must
not be operated without these devices correctly fastened in position.
By following all instructions in this manual, you increase the life of your machine and keep its maximum
performance. Adjustments and maintenance must always be done by an approved technician.
If additional information or service is needed. Contact your Authorized Ransomes Jacobsen Dealer, who knows
the latest methods to service this equipment and can give that service.
WARNING
The Interlock System on this mower prevents the starting of the mower unless a.) The parking brake is
Engaged. b.) The mow switch is in the OFF position, c.) The traction pedal is in the Neutral position. d) The
operator is in the seat. The system stops the engine when the operator leaves the seat a.) without the parking
brake engaged or b.) the mow switch is not in the OFF position. NEVER operate the mower unless the
Interlock System is working.
WARNING
1. Before leaving the operator’s position for any reason:
a. Return traction pedal to the Neutral position.
b. Disengage all drives.
c. Lower all implements to the ground.
d. Engage parking brake.
e. Stop the engine and remove the ignition key.
2. Keep your hands, feet, and clothing away from moving parts. Wait for all movement to stop before you
clean, adjust, or service the machine.
3. Keep the area of operation clear of all persons and animals.
4. Never carry any passengers.
5. Never operate the equipment without a correctly fastened grass deflector in position.

en-14
3 SAFETY
WARNING
California Proposition 65
Engine Exhaust, Some Of Its Constituents, And Some Vehicle Components Contain Or Release Chemicals
Known To The State Of California To Cause Cancer And Birth Defects Or Other Reproductive Harm.
WARNING
To Prevent Injury From The Hot Oil At High Pressure, Do Not Use Your Hands To Check For Oil Leaks. Make
Sure That You Use Paper Or Cardboard.
Release Of Hydraulic Fluid At High Pressure Has Enough Force To Enter Through The Skin. If The Fluid Enters
Through The Skin, The Fluid Must Be Surgically Removed Within Hours By A Specialist Doctor Or Gangrene
May Result.
WARNING
When The Machine Is Driven Off-Road, A Seat Belt Must Be Worn Only When A Rops Frame Is In Position.
This Warning Is Because A Seat Belt Must Be Worn With A Rops To Follow The Machinery Directive,
2006/42/EC Sections 3.2.2, Seating & 3.4.3, Rollover. (ANSI B71.4-2012 section 20.7)
Ransomes Jacobsen Limited Recommends That The Owner/User Of The Machine Completes A Local Risk
Assessment Of The Machine To Find Any Conditions That Do Not Follow This Rule. E.g. When You Drive The
Machine Next To Water Or On The Highway.
WARNING
Explosive Gases Are Released By Batteries. The Battery Contains Corrosive Acid And Supply An Electrical
Current That Is High Enough To Cause Burn Injuries To The Body.
WARNING
You Must Not Use This Machine To Tow Other Vehicles.
WARNING
Ear Protection Must Be Worn When You Operate Machines With
An Operator Ear Noise Level Of More Than 85 db(A) Leq.

en-15
SAFETY 3
WARNING
Vibration Exposure Limits
Exposure limits are calculated as a combination of the vibration level (magnitude) of the tool and the
Daily Exposure Time (Trigger Time). E.g. A product with 5m/s² vibration can be used up to 2 hours/day to
reach the EAV and up to 8 hours/day to reach the ELV.
Exposure Action Value (EAV) - Daily vibration exposure A(8) = 2.5m/s²
Where daily vibration exposure A(8) is below 2.5m/s² the risk is relatively low and no action need be
taken
Exposure Limit Value (ELV) - Daily Vibration Exposure A(8) = 5.0m/s²
If several tools are use the exposure values must be combined:
Total exposure is then the combined value of the activities
WARNING
Never Mow If There Is A Risk Of Lightning Or You Hear Thunder. If You Are In The Middle Of Mowing,
Stop In A Safe Place, Turn Off The Engine And Go Inside a Building.
CAUTION
When You Do Any Welding On The Machine, The Battery, Controller And Display Must Be Disconnected
Before You Start. You Must Not Open The Controller. If The Controller Is Opened, This Can Cancel All Of The
Warranties And Can Cause The Failure Of The Machine.
CAUTION
Personal Protective Equipment (PPE), For Example Safety Glasses, Leather Work Shoes Or Boots, A Hard
Hat, Leather Work Gloves And Ear Protection Must Be Used After The Owner/User Completes A Local Risk
Assessment Of The Mower, To Prevent Injury.
Training In All Manual Operations Must Be Given By An Approved Person Before The Machine Is Used The
First Time.

en-16
4 SPECIFICATIONS
4.1 ENGINE SPECIFICATION ______________________________________________
Model: V1505T-E2B-RANUK-1
Type: Vertical, water-cooled, 4-cycle diesel engine
Number of Cylinders 4
Bore & Stroke 74mm x 78.4mm
Total Displacement 1498cm³
Combustion Chamber Spherical type (E-TVCS)
Intake System Turbo Charged
Gross Intermittent Power 31.3 kW @ 2850 RPM
Maximum Speed: 3000 ± 50 RPM (No load)
Idle Speed: 1500 ± 100 RPM
Order of Firing 1-3-4-2
Direction of Rotation Counter-clockwise (viewed from flywheel side)
Injection Pump Bosch MD type mini pump
Injection Pressure 13.73 MPa (140kgf/cm²)
Injection Timing (Before T.D.C.) 18°
Compression Ratio 23.5:1
Fuel: No. 2-D Diesel fuel (ASTM D975)
Lubrication (API Classification) Above CD grade
Oil Sump Capacity: 6.4 litres
Dimensions (length x width x height) 591.3mm x 439.2mm x 613.7mm
Dry Weight 114kg
Starting System Cell starter (with glow plug)
Starting Motor 12V, 1.4kW
Charging Generator 12V, 360w

en-17
SPECIFICATIONS 4
4.2 MACHINE SPECIFICATION _____________________________________________
Frame construction:Heavy duty formed steel chassis with box section frame rails.
Cutting unit drive:Fixed displacement hydraulic motors.
Transmission:Four wheel drive on demand. Direct coupled variable displacement pump to direct coupled 280cc/
rev front, 139cc/rev rear wheel motor.
Speeds:
Cutting: 0 - 12 km/h (7.7 mph) Forward
0 - 12 km/h (7.5 mph) Reverse
Transport: 0 - 25 km/h (15.5 mph) Forward
0 - 05 km/h (3 mph) Reverse
Steering:Hydrostatic power steering, with adjustable tilt steering wheel.
Ground pressure:1 kg/cm² (14.2 psi) (Dependent on tyre pressures and accessories fitted)
Brakes: Hydrostatic braking with hydraulic parking brakes on front wheels.
Battery: Type 093 (SAE 500)

en-18
4 SPECIFICATIONS
4.3 DIMENSIONS & WEIGHTS METEOR FLAIL __________________________________
metric US
A Width of Cut: 214 cm 84.3 in
B Maximum width Cutting: 232 cm 91.3 in
C Maximum width Transport (minimum): 155 cm 63 in
D Maximum height with ISO21299 ROPS Frame up: 219 cm 86.2 in
E Maximum height with OECD code 4 Tested ROPS Frame up: 227 cm 89.3 in
F Maximum height with ROPS Frame down: 150 cm 59 in
Maximum height with Cab 224 cm 88 in
G Total Length: 282 cm 111 in
H Length with ISO 21299 ROPS Frame Down, Add: 10 cm 3.9 in
J Length with OECD code 4 ROPS Frame Down, Add: 10 cm 3.9 in
Weight of Machine with ROPS, No Fuel. 1082 kg 2419 lb
Weight of Machine with cab, No Fuel. 1277 kg 2848 lb
Weight of 51 litres (13.5 Imp gallon) of Diesel Fuel 48kg 105lbs
Weight of one Front Meteor Cutting Unit 84 kg 185.2 lb
Weight of Storage Rack 5 kg 11 lb
K Wheel Base 149.5 cm 58.8 in
L Wheel Track Front 129.5 cm 60 in
M Wheel Track Rear 110 cm 43.3 in
TYRE PRESSURE
Front Wheel Rear Wheel
Tyre Size Tyre Type Tyre Pressure Tyre Size Tyre Type Tyre Pressure
26 x 12.00 -
12
Grassmaster
6pr
1.00 - 1.37 bar (14.5 -
20 psi)
20.00 x 10.00
- 8
Grassmaster
4pr
1.00 - 1.37 bar (14.5 - 20
psi)
26 x 12.00 -
12 Armour 6pr 1.00 - 1.37 bar (14.5 - 20 psi)
20.00 x 10.00
- 8 Armour 6pr 1.00 - 1.37 bar (14.5 - 20 psi)
N
P
With OECD Code 4

en-19
SPECIFICATIONS 4
A
B
C
L
M
G
H
D
F
K
With ISO 21299 ROPS
With OECD code 4 Tested ROPS
A
B
C
L
M
G
H
D
F
K

en-20
4 SPECIFICATIONS
4.4 DIMENSIONS & WEIGHTS WITH MAGNA 250 AND SPORT200________________
metric US
A Width of Cut: 215 cm 84.6 in
B Maximum width Cutting: 240.5 cm 94.6 in
C Maximum width Transport (minimum): 160 cm 63 in
D Maximum height with ISO21299 ROPS Frame up: 219 cm 86.2 in
E Maximum height with OECD code 4 Tested ROPS Frame up: 227 cm 89.4 in
F Maximum height with ROPS Frame down: 150 cm 59 in
N Maximum height with Cab 224 cm 88 in
P Additional height with beacon 14.5 cm 5.7 in
G Total Length: 267 cm 105.1 in
H Length with ISO 21299 ROPS Frame Down, Add: 10 cm 4 in
J Length with OECD code 4 ROPS Frame Down, Add: 10 cm 4 in
Weight of Machine with ROPS, No Fuel. 1130 kg 2491.22 lb
Weight of Machine with cab, No Fuel. 1325 kg 2921.1 lb
Weight of 51 litres (13.5 Imp gallon) of Diesel Fuel 48kg 105lbs
Weight of one Magna 250 4 Knife Cutting Unit (Fixed) 70 kg 154.3 lb
Weight of one Magna 250 6 Knife Cutting Unit (Fixed) 75 kg 165.3 lb
Weight of one Magna 250 8 Knife Cutting Unit (Fixed) 77 kg 169.7 lb
Weight of one Sport 200 4 Knife Cutting Unit (Fixed) 63 kg 138.9 lb
Weight of one Sport 200 6 Knife Cutting Unit (Fixed) 68 kg 149.9 lb
Weight of one Sport 200 8 Knife Cutting Unit (Fixed) 70 kg 154.3 lb
Weight of one Sport 200 6 Knife Cutting Unit (Floating) 84 kg 185.2 lb
Weight of one Sport 200 8 Knife Cutting Unit (Floating) 86.5 kg 190.7 lb
Weight of Storage Rack 5 kg 11 lb
K Wheel Base 149.5 cm 58.8 in
L Wheel Track Front 129.5 cm 51 in
M Wheel Track Rear 110 cm 43.3 in
Uncut Turning Circle 130 cm 51.2 in