Textron Jacobsen Tri-King 67139 User manual

Instruction
Sheet
When Performance Matters.
™
WARNING
If incorrectly used, this machine can cause severe injury. Those who use
and maintain this machine should be trained in its proper use, warned of its
dangers and should read the entire manual before attempting to set up,
operate, adjust, or service the machine.
19
17
18
13
6
5
9
15
16
7 8
10
4
3
11
1-INCLUDESITEMS3 - 16
Tri-King® Vertical Mower
Left Front Mower Product No. 67139
Right Front Mower Product No. 67140
Center Mower Product No. 67141
4113401

2
This kit is intended for use on Jacobsen® Tri-King™ 1800G and
1900D mowers.
PREPARATION ___________________________________________________________________________________
1. Park the mower on a flat and level surface, fully lower the
cutting units to the ground, engage the parking brake,
stop the engine and remove key from ignition switch.
a. Wait for all movement to stop before making any
adjustments or modifications.
b. Take this opportunity to thoroughly inspect the
equipment and perform other maintenance.
c. For all steps, refer to the Parts List for part
identification.
2. Following instructions given in the Parts & Maintenance
Manual remove any existing cutting units from mower
and place protective plug over the bearing housing cavity.
Note: This kit will fit a Tri-King with existing 26” cutting units
directly. If your machine is equipped with 30” cutting units, or
does not have cutting units, contact your nearest Jacobsen
dealer to order parts required for installation.
If your machine is equipped with 30” cutting units, the following
parts are required:
2811280 - 1 - Right Lift Arm
2811281 - 1 - Left Lift Arm
2811128 - 2 - Spring Plate
If your machine does not have cutting units, the following parts
are required:
2811280 - 1 - Right Lift Arm
2811281 - 1 - Left Lift Arm
400260 - 2 - Screw, 3/8-16 x 7/8" (Front Mowers to Lift Arm)
446142 - 2 - Lockwasher, 3/8 Heavy (Front Mowers to Lift Arm)
364781 - 2 - Washer (Mower to Lift Arm)
3002718 - 1 - Collar (Center Mower to Lift Arm)
3005435 - 1 - Pin, Spring Lock
400262 - 4 - Screw, 3/8-16 x 1" (Spring Plug to Spring Plate)
446142 - 4 - Lockwasher, 3/8 Heavy (Spring to Spring Plate)
441904 - 2 - Carriage Bolt, 1/2-13 x 10" (Spring Plate to Lift Arm)
452012 - 2 - Flat Washer, 1/2 (Spring Plate to Lift Arm)
443118 - 2 - Nut, 1/2-13 Hex (Spring Plate to Lift Arm)
2811128 - 2 - Spring Plate
3007908 - 4 - Plug, Spring
364157 - 4 - Spring, Down Pressure
364160 - 4 - Shackle (Spring to Mower)
1001854 - 4 - Shackle (Lift Arm to Mower)
3004065 - 2 - Chain, Lift (Lift Arm to Mower)
TO ORDER PARTS ___________________________________________
1. Write your full name and complete address on the order.
2. Explain where and how to make shipment.
3. Give product number, name and serial number that is stamped on the name plate or serial plate of your product.
4. Order by the quantity desired, the part number, and description of the part as given in the parts list.
5. Send or bring the order to an Authorized Jacobsen Dealer.
6. Inspect all shipments on receipt. If any parts are damaged or missing, file a claim with the carrier before accepting.
7. Return material to an Authorized Jacobsen Dealer with a letter of explanation, listing the parts being returned. Transpor-
tation charges must be prepaid.
Use of other than original Jacobsen parts or Jacobsen authorized parts will void the warranty.
CAUTION
Read the Safety & Operation Manual and become
familiar with the controls and proper use of the
equipment.
Stay alert for potential hazards and follow all safety
precautions. Read all instructions completely and make
sure you understand them before proceeding with the
assembly.
!
WARNING
Before you clean, adjust, or repair this equipment,
disengage all drives, lower cutting units to the ground,
engage parking brake, stop engine, remove key from switch
and disconnect Negative (BLACK) battery cable to prevent
injuries
!
Litho in U.S.A. 9-2008

3
LIFT ARM INSTALLATION (UNITS WITH 30” REELS OR UNITS WITHOUT EXISTING REELS ___________________
1. Assemble lift arms (J) to the mower
a. Remove nut and bolt (K) then remove pin (L).
b. Place lift arm (J) in cradle and slide pin (L) through
the cradle and lift arm. Secure pin with hardware
(K).
c. Assemble shackles (N) to the chains then assemble
each chain to crank (M). Secure with pins (P).
d. Assemble free end of chain to lift arm (J) and
secure with pins (P).
e. Repeat Steps a-d for the other side.
DO NOT assemble Down Pressure Springs. They will be
installed after vertical mowers.
Figure 1
Figure 2
FRONT MOWERS _________________________________________________________________________________
1. Remove the left and right mower assemblies from the
shipping crates. Remove hardware (H) from lift arm (J).
2. Assemble the front mowers to the lift arms with
hardware (H).
3. Remove the cover plate (S) from the drive end of each
mower. Retain hardware (U) and gasket (R). Store
cover plate (S) for future use.
4. Install motors on mowers with hardware (U) and
gasket (R). Nut (T) must be facing upwards as shown.
Figure 3A
Figure 3B
J
K
K
L
M
N
P
J
R
S
T
U
H
J

4
CENTER (REAR) MOWER___________________________________________________________________________
1. Remove center mower from its shipping crate and
position behind the rear lift arm (Z). Slide the mower onto
the lift arm and secure with collar (V) and spring clip pin
(W).
2. Remove the cover plate (S) from the drive end of center
mower. Retain hardware (U) and gasket (R). Store cover
plate (S) for future use.
3. Install motor on cutting unit with hardware (U) and
gasket (R). Nut (T) must be facing upwards as shown.
4. Secure hose bracket (X) to stud of center mower with
3/8-16 hardware (Y).
Figure 3
DOWN PRESSURE SPRINGS (UNITS WITH 30” MOWERS AND UNITS WITHOUT EXISTING MOWERS ___________
1. Start the engine and fully raise the lift arms.
2. Stop the engine and lock the arms in transport position.
a. Remove pin (A) and slide handle (B) from the top slot
(C) to the bottom slot (D).
b. Insert pin (A) to lock handle (B) in place.
Note: To prevent damage to the mower, the transport
lock must be disengaged before the cutting units can be
lowered.
3. Assemble plug (H) into each spring (J).
4. Assemble 3/8-16 x 1” bolt (E), lockwasher (F) and plate
(G) as shown. [Figure 5]
5. Assemble 1/2-13 x 10” bolt (P), flat washer (Q) and nut
(R) as shown. Thread bolt (P) at least 1-1/2” into plate
(G).
6. Manually raise the front lift arms as far as possible then
tether the arms together.
7. For 26 in. cutting units assemble shackles (K) to each tab
(M) and secure with clevis and cotter pin (L).
8. Connect springs (J) to shackles (K) then remove tethers
and transport lock.
9. Adjust down pressure. [See Parts & Maintenance]
Figure 4
Figure 5
T
Y
U
R
S
X
W
V
Z
AB
C
D
C
BA
G
HJ
K
EF
PQ
R
M
L
L

5
OPERATION________________________________________________________________________________________
1. The vertical mowers operate in forward rotation allowing
each blade tip to break (cut) new turf and therefore
requires more power than normal mowing.
a. Do not operate the vertical mowers when the
hydraulic reel motors are loaded to a point where
they stall or slow down.
b. The operator must adjust the ground speed to
accommodate for the cutting conditions and power
requirements.
c. If the mower slows down under load, it is an
indication that the cut may be too deep.
2. The vertical mowers were designed to mow at depths of
1/8 to 1/4” (3.2 - 6.4 mm) above the roller, depending on
turf conditions and operations being performed. A greater
cutting depth may damage the root structure and
increase power requirements. It is recommended to begin
with a higher setting and gradually lower blades until
desired results are obtained.
a. Grain control (light and frequent operation) - half of
normal cutting height.
d. Thatch removal (every 60 to 90 days) - 1/8” to 1/4”
setting.
e. Renovation (heavy thatch removal) - not
recommended with Tri-King vertical mowers.
3. Vertical mowing is an operation that can create a lot of
dust and debris. Special care must be taken to clean the
air intake system on the Tri-King at regular intervals.
Check the air intake system if the water temperature
gauge (Diesel Units) indicates an elevated temperature
level.
ROLLERS __________________________________________________________________________________________
1. When replacing the bearing (A) the cup and cone should
be replaced in sets. Hand pack each bearing cone with a
good grade of multi purpose Moly 2 EP grease.
2. To remove the bearing cup use a blind hole bearing
puller.
3. When installing the seals (B and C) be sure the lip is
towards the center of the roller.
4. After complete reassembly of the roller tighten locknut (D)
to 10 - 30 ft./lbs. to seat bearings. Readjust locknut to
develop 3 to 7 in./lb. rotational torque resistance on shaft.
Check torque resistance of roller after 25 - 50 hours of
operation and every 250 hours after that.
5. If lubricant inside of roller has been flushed during
disassembly, apply 15 - 20 pumps of multi purpose Moly
2 EP grease with a hand gun into fitting after roller has
been reassembled.
Figure 6
CUTTING DEPTH ADJUSTMENT _______________________________________________________________________
1. To achieve the desired depth of cut, place an adjusting
gauge at either end of the cutting unit across the two
rollers as shown. [Figure 3]
2. Adjust the cutting depth of the blade with the rear
adjusting nuts. For most applications front adjusters
should be positioned with the top bolt passing through the
second hole from bottom as shown. [Figure 7]
a. Turn the end blade so that one tooth of the blade is at
90 degrees to the top of the gauge as shown.
b. The blades should be adjusted to be at the same
depth at both ends of the cutting unit. [within 1/64”
(.4mm) inch]
3. The ground line should be close to parallel with the
bottom of the mower frame to assure proper cutting and
discharge angle. As the blade wears the front adjuster
can be repositioned to allow proper cutting angle and
depth.
Figure 7
CAUTION
To prevent contamination of the engine compartment, do
not operate the mowers in reverse rotation.
!
A
B
C
D
+
Desired Depth
Gauge
Rear
Roller
Front
Roller
90˚

6
ADDING, REMOVING OR REPLACING BLADES ________________________________________________________
1. Blades may be replaced without removing the cutting unit
from the frame.
2. Loosen blade nut (B) from 1/4” to 3/8” (6.3 to 9.5 mm)
towards the frame.
a. Pull spacer (C) next to the blade (D) to be removed
toward the nut to disengage it from the locking lugs
on the spacer.
b. Remove blade from the shaft. Install replacement
blade with the slot in blade in same position as blade
that was removed and retighten nut (B) securely.
(Torque nut to 12-15 ft. lb. (16-20 N.m)
3. Blade spacing can be adjusted for different modes of
operation, from 1/2” (13 mm) to 1-1/2” (32 mm) in 1/4”
increments (6 mm).
a. 1” (25 mm) spacing between blades is the standard
factory setting.
b. 3/4” (19 mm) to 1-1/2” (38 mm) spacing is
recommended for fairways, greens surrounds and
sport fields.
c. 3/4” (19 mm) to 1” (25 m) spacing is recommended
for tee tops.
Figure 8
B
C
D

7
MAINTENANCE _____________________________________________________________________________________
Proper adjustments and regular maintenance are essential to the
performance of your machine. If proper adjustment cannot be
made, contact an Authorized Jacobsen Dealer.
1. Inspect your machine on a regular basis and replace
worn or damaged parts before operating machine or
before actual breakdown occurs.
2. Establish a regular maintenance schedule.
a. Keep the mower clean and all moving parts properly
adjusted.
b. Keep shields in place and all hardware securely
tightened.
3. Wash the unit after each use.
4. Clean all plastic or rubber trim with a mild soap solution
or use commercially available vinyl/rubber cleaners.
5. Repair damaged metal surfaces and use Jacobsen
Orange touch-up paint.
WARNING
Before you clean, adjust, or repair this equipment, disengage
all drives, lower cutting units to the ground, engage parking
brake, stop engine, remove key from switch and disconnect
battery to prevent injuries
!
CAUTION
Do not wash any portion of the equipment while it is hot.
Do not use high pressure spray or steam. Use cold water
and automotive cleaners.
!
Support ___________________________________________________________
If you encounter any problems while installing this kit,
contact your Jacobsen Dealer or contact the Jacobsen
Customer Care department.
Jacobsen, A Textron Comany
11108 Quality Drive
Charlotte, NC 28273
800-848-1636
http://www.Jacobsen.com

8
4
3
2
9
33
34
35
24
30
31
8
7
6
5
27
13
18
19
20
20
21
21
21
22
23
29
26 36
32
25
28
12
13
11
10
2
3
4
6
5
1
14
15
16
17
TRI-KING VERTICAL MOWER
1.1 Bearing Housing Serial No. All

9
> Change from previous revision
TRI-KING
Item Part No. Qty. Description Serial Numbers/Notes
15001606 1 Housing
2 500596 2 • Bearing, Cup and Cone
3 3000983 1 • Oil Seal
4 3001152 1 • Washer
5 471214 1 • Grease Fitting
6 471242 1 • Relief Fitting
7 5001607 1 Motor Housing (Includes 2 ~ 6 and 8)
8 3003086 2 • Stud
9 364148 1 Compression Spring
10 364283 1 Tube, Spacer
11 364259 1 Washer, Bearing Retainer
12 400264 1 Screw, 3/8-16 x 1-1/4” Hex Head
13 446142 5 Lockwasher, 3/8 Hvy
14 364147 1 Gasket, Cover
15 338585 1 Cover
16 446116 4 Lockwasher, #10
17 434038 4 Screw, #10-24 x 1/2”
18 2812091 1 Vertical Reel Assembly
19 2812090 1 • Shaft
20 2812086 22 • Blade
21 3007137 86 • Spacer, Blade
22 2812085 1 • Collar
23 348576 1 • Nut, 1-3/4 - 5 Hex
24 415522 1 • Set Screw, 5/16-18 x 3/8” Soc Hd
25 4112881 2 Carriage Bolt, 5/8-11 x 2”
26 4112921 2 Nut, 5/8-11 Spiralock Flange
27 400258 4 Screw, 3/8-16 x 3/4” Hex Head
28 364282 1 Support Plate
29 4112882 2 Spacer
30 3003389 2 Housing, Pivot Bushing
31 400446 2 Screw, 1/2-20 x 2” Hex Head
32 445789 2 Nut, 1/2-20 Spiralock
33 458039 1 External Snap Ring
34 503684 1 Motor Coupler
35 364151 2 Wave Washer
36 1001643 1 Frame

10
TRI-KING VERTICAL MOWER
2.1 Rollers Serial No. All
13
10
10
20
11
19
17
15
17
13
10
14
18
16
12
7
4
8
9
1
1
5
2
6
3

11
> Change from previous revision
Item Part No. Qty. Description Serial Numbers/Notes
1132639 2 Roller
2 3005156 2 • Wear Sleeve
3 3004882 2 • Oil Seal
4 338647 2 • Oil Seal
5 500534 2 • Bearing, Cup and Cone
6 367029 2 • Nut
7 471214 2 • Grease Fitting
8 N/S 1 • Tube, Roller
9 3003415 1 • Shaft, Roller
10 446142 8 Lockwasher, 3/8 Hvy
11 3008359 1 L.H. Front Roller Bracket
12 3008360 1 R.H. Front Roller Bracket
13 443110 8 Nut, 3/8-16 Hex
14 471214 2 Grease Fitting
15 3007673 2 Housing
16 132680 2 Rear Roller Adjuster
17 3000313 4 Adjusting Nut
18 412015 4 Set Screw, 5/16-18 x 5/8”
19 400264 8 Screw, 3/8-16 x 1-1/4” Hex Head
20 366653 2 Washer
TRI-KING VERTICAL MOWER

12
12
11
10
28 13
24
25
10
8
7
6
4
12
11
10
9
19
18
18
17
20
21
6
5
15/16
27
26
26
22/23
20
31
13 11
3
2
29
11
30
11
12
14
1
1
25
(67141)
25
(67139)
25
(67141)
25
(67140)
To prevent injury, disengage
all drives, engage parking
brake and stop engine before
working in machine or
emptying grass catchers.
!DANGER
TRI-KING VERTICAL MOWER
3.1 Shields and Pivot Arm Serial No. All

13
> Change from previous revision
TRI-KING VERTICAL MOWER
Item Part No. Qty. Description Serial Numbers/Notes
1116850 1 Left Pivot Arm 67139 Only
364156 2 • Bushing 67139 Only
1 116849 1 Right Pivot Arm 67140 Only
364156 2 • Bushing 67140 Only
1 1000848 1 Center Pivot Arm 67141 Only
364140 2 • Bushing 67141 Only
2 338561 1 Reel Pivot Bracket
3 338562 1 Reel Pivot Bracket
4 364302 2 Pivot Spacer
5 400408 2 Screw, 1/2-13 x 1-1/2” Hex Head
6 452012 4 Flat Washer, 1/2
7 446154 2 Lockwasher, 1/2 Hvy
8 443118 2 Nut, 1/2-13 Hex
9 400264 2 Screw, 3/8-16 x 1-1/4” Hex Head
10 453011 AR Washer, 3/8
11 446142 12 Lockwasher, Hvy
12 443110 6 Nut, 3/8-16 Hex
13 400260 6 Screw, 3/8-16 x 7/8” Hex Head
14 471214 1 Grease Fitting
15 3002813 1 Reel Bumper Bracket (Shown) 67141 Only
16 3002814 1 Reel Bumper Bracket 67141 Only
17 361723 2 Rubber Bumper 67141 Only
18 443810 4 Nut, 3/8-16 Jam 67141 Only
19 400190 4 Screw, 5/16-18 x 1-1/4” Hex Head 67141 Only
20 446136 4 Lockwasher, 5/16 Hvy 67139 and 67140 Only
20 446136 8 Lockwasher, 5/16 Hvy 67141 Only
21 443106 4 Nut, 5/16-18 Hex 67141 Only
22 122875.6 1 Rear Shield (Front Mowers) 67139 and 67140 Only
23 1003056.6 1 Rear Shield (Rear Mower) 67141 Only
24 5003650 1 Shield
25 361877 AR • Decal, Danger
26 3000718 2 Shield Shim
27 364281 2 Backup Nut
28 364150 2 Clamp
29 364777 1 Gasket
30 400258 2 Screw, 3/8-16 x 3/4” Hex Head
31 400186 4 Screw, 5/16-18 x 7/8” Hex Head

Jacobsen, A Textron Company
11108 Quality Drive, Charlotte, NC 28273
www.Jacobsen.com
800-848-1636
Equipment from Jacobsen is built to exacting
standards ensured by ISO 9001 and ISO 14001
registration at all of our manufacturing locations.
A worldwide dealer network and factory trained
technicians backed by Jacobsen Parts Xpress
provide reliable, high-quality product support.
When Performance Matters.
™

WARNING
Warning: If incorrectly used, this machine can
cause severe injury. Those who use and maintain
this machine should be trained in its proper use,
warned of its dangers, and must read the entire
manual before attempting to set up, operate, adjust,
or service the machine.
When Performance Matters.
™
GB
Parts Manual
Jacobsen TR320 Ride on Cylinder Trim Mower
68021-B000 – TR320, Kubota®D1105-E4B, 3WD, Treaded Tires
68021-B100 – TR320, Kubota®D1105-E4B, 3WD, Treaded Tires
68021-B200 – TR320, Kubota®D1105-E4B, 3WD, Treaded Tires
677799-Rev A

Copyrighted Material
This manual may not re reproduced in whole or in part without the
express permission of TSV (Augusta) Technical Communications
Department.
This manual contains adjustment, maintenance,
troubleshooting instructions and parts list for your new
Jacobsen machine. This manual should be stored with
the equipment for reference during operation.
Before you operate your machine, you and each operator
you employ should read the manual carefully in its
entirety. By following the safety, operating and
maintenance instructions, you will prolong the life of your
equipment and maintain its maximum efficiency.
If additional information is needed, contact your
Jacobsen Dealer.
The serial plate is located on the left rear frame rail.
Jacobsen recommends you record these numbers below
for easy reference.
CHARLOTTE, NC PRODUCT OF U.S.A.
®
A Textron Company
2
Proposition 65 Warning
This product contains or emits
chemicals known to State of California
to cause cancer and birth defects or
other reproductive harm.
FOREWORD
Suggested Stocking Guide
To Keep your Equipment fully operational and productive, Jacobsen suggests you maintain a stock of the more
commonly used maintenance items. We have included part numbers for additional support materials and training aids.
To order any of the following material:
1. Write your full name and complete address on your
order form.
2. Explain where and how to make shipment:
❑UPS ❑Regular Mail
❑Overnight ❑2nd Day
3. Order by the quantity desired, the part number, and
the description of the part.
4. Send or bring the order to your authorized Jacobsen
Dealer.
02-2018
Service Parts
Service Support Material
Qty. Part No. Description Qty. Part No. Description
4113986 Engine Oil Filter 4283654 Ignition Key
5000913 Element, Engine Air Filter 4176550 Engine Fan Belt
550489 Cartridge, Engine Fuel Filter
2811255 Charge Filter
Qty. Part No. Description
677802 Safety & Operation Manual
677799 Parts Manual
TBD Service Manual
Diesel Engine Parts Manual
Qty. Part No. Description

Table of Contents
1
1.1 ......... Operator Platform ............................................... 4
1.1 ......... Seat Option .......................................................... 1
3.1......... Armrest and Control Panel ................................ 8
4.1 ......... Traction Pedal ................................................... 10
5.1 ......... Traction Linkage ............................................... 12
6.1 ......... Chassis .............................................................. 14
7.1 ......... Front Axle Assembly ........................................ 16
8.1 ......... Front Axle .......................................................... 18
9.1.........Rear Axle Assembly ......................................... 20
10.1 ....... Rear Axle ........................................................... 22
11.1 ....... Air Filter ............................................................. 24
12.1 ....... Radiator ............................................................. 26
13.1 ....... Remote Engine Oil Cooler and Filter .............. 28
14.1 ....... Engine Mounting ............................................... 30
15.1....... Engine and Pumps............................................ 32
16.1 ....... Engine Exhaust ................................................. 34
17.1 ....... Fuel Tank and Routing ..................................... 36
18.1.......Hydraulic Tank and Hood................................. 38
19.1.......Hydraulic Valve Assembly ............................... 40
20.1 ....... 3WD Traction Hydraulics ................................. 42
21.1.......3WD Gear Pump and Steering Hydraulics...... 44
22.1.......Front And Rear Reel Hydraulics...................... 46
23.1.......Front And Rear Lift Hydraulics........................ 48
24.1 ....... Drain Hydraulics ............................................... 50
25.1.......Brake Valve and Charge Hydraulics ............... 52
26.1 ....... Oil Cooler Hydraulics ....................................... 54
27.1....... Electrical ........................................................... 56
28.1....... Mounting And Lift Arms .................................. 58
29.1 ....... Pivot Arms ......................................................... 60
30.1....... Inner Reel Assembly......................................... 62
31.1 ....... Outer Reel .......................................................... 64
32.1.......Roller Brackets and Skids................................ 66
33.1 ....... Standard Unit Fixing ......................................... 68
34.1 ....... Grass Catcher ................................................... 70
35.1....... Brake Valve....................................................... 72
36.1 ....... Reel Valve .......................................................... 73
37.1 ....... Lift-Weight Transfer Valve ............................... 74
38.1 ....... Reel Motor ......................................................... 75
39.1 ....... Steering Cylinder .............................................. 76
40.1 ....... Front Lift Cylinder ............................................. 78
41.1....... Rear Lift Cylinder .............................................. 79
42.1 ....... Steering Valve ................................................... 80
43.1 ....... Gear Pump ......................................................... 82
44.1 ....... Traction Pump ................................................... 84
44.1....... Traction Pump (Continued).............................. 86
45.1....... 3WD Rear Wheel Motor .................................... 88
46.1 ....... Electrical Schematic ......................................... 90
47.1 ....... Hydraulic Schematic......................................... 94

4
TR320
1.1 Operator Platform Serial No. All
1
1
1
12
3
4
4
5
5
5
6
6
7
8
9
10
10
11
12
12
13
14
31
15
16
16
17
17
18
19
20
20
21
21
27
27
26
26
28
28
29
29
22
23
23
24
25
4397486
®
3008682
4181865 REV B
3
30
32
14°+
009114550

5
> Change from previous revision
TR320
Item Part No. Qty. Description Serial Numbers/Notes
1001191331 4 Screw, M5-0.8 x 16 mm Taptite
2 001496150 16 Pop Rivet, 3.2 x 10 mm Stainless Steel
3 4314427 4 1/4 Turn Fastener
4 4314429 4 1/4 Turn Steel Retainer
5 4314430 4 1/4 Turn Receptacle
6 4394747 2 Cover, Chassis End
7 671357 1 Platform, Operator
8 4395663 1 Cover, Steering Tower
9 671682 1 Adhesive Foam, 578 mm
10 4395665 2 Adhesive Foam, 3 x 4 x 90 mm
11 4395666 1 Adhesive Foam, 4 x 5 x 529 mm
12 4395667 2 Adhesive Foam, 3 x 5 x 202 mm
13 671556 1 Plate, Rear Backing
14 671585 1 Panel, Rear Service
15 4395869 1 Panel, Floor Service
16 450029 4 Hex Head Screw, M10-1.5 x 35 mm
17 450241 4 Hex Head Screw, M12-1.75 x 30 mm
18 450357 4 Nut, M6-1 Insert (0.7 to 4.2)
19 450389 4 Washer, M6 x 12.5 x 1.8
20 450391 4 Washer, M10 x 21 x 2.2
21 450392 4 Washer, M12 x 24 x 2.7
22 450541 4 Pan Head Screw, M6-1 x 16 mm
23 452437 4 Nut, M10-1.5 Flange Nyloc
24 452438 2 Nut, M12-1.75 Flange Nyloc
25 002953223 3 Grommet, 20.6 x 31.8 x 9.5 mm
26 4397486 1 Decal, Traction Pedal
27 669813 1 Decal, Jacobsen Decal
28 4181865 1 Decal, Mower Warning
29 3008682 1 Decal, Tow Valve
30 4420394 1 Floor Board Grip Tape
31 4420395 1 Access Panel Grip Tape
32 009114550 1 Decal, Max Slope 14 Deg

1
TR320
1.1 Seat Option Serial No. All
Standard Seat Option
26
26
12
1
215
17
5
6
7
19
10
9
9
16
11
14
16
7
8
22
21
13
25
25
24
23
1824
23
18
6
45
13
17
20
17
17
20
13
1317
13
3
17
15
13
27