Textron Ransomes LH Series Guide

®
RJL 100 April 2010
GB
United
Kingdom
DE
Germany
Safety, Operation & Maintenance Manual
Sicherheits-, Bedienungs- und Wartungshandbuch
Ransomes Mounted 214 Reel Mower & Ransomes Verticut 214
Aufsitzzylindermäher Ransomes Mounted 214 & Ransomes Verticut 214
Series: LH, LJ, LK, LM
Product code: LKCB104, LKCB105, LKCB106, LKCB120, LKCB204, LKCB205,
LKCB206, LKCB220
Serie: LH, LJ, LK, LM
Produktcode: LKCB104, LKCB105, LKCB106, LKCB120, LKCB204, LKCB205,
LKCB206, LKCB220
WARNING
WARNING: If incorrectly used this machine can cause severe injury.
Those who use and maintain this machine should be trained in its
proper use, warned of its dangers and should read the entire manual
before attempting to set up, operate, adjust or service the machine.
ACHTUNG
ACHTUNG: Wenn diese Maschine nicht ordnungsgemäß verwendet
wird, können ernsthafte Verletzungen verursacht werden. Personen,
die diese Maschine verwenden und warten, müssen in ihrer richtigen
Verwendung ausgebildet sein, auf die Gefahren aufmerksam
gemacht worden sein und die Anleitung ganz gelesen haben, bevor
sie versuchen, die Maschine aufzustellen, zu bedienen, einzustellen
oder zu warten.
23912G-DE (rev.3)

©2010, Ransomes Jacobsen Limited. All Rights Reserved / Alle Rechte vorbehalten
Ransomes Jacobsen Limited reserves the right to make design changes without obligation to make these
changes on units previously sold and the information contained in this manual is subject to change without notice.
Ransomes Jacobsen Limited behält sich das Recht zu Konstruktionsänderungen vor ohne Verpflichtung, diese
Änderungen an schon verkauften Geräten vorzunehmen. Die Informationen in diesem Handbuch können ohne
vorherige Ankündigung geändert werden.

SAFETY & OPERATORS MANUAL
GB-3
1CONTENTS
2.1 IMPORTANT .......................................................................4
2.2 PRODUCT IDENTIFICATION .............................................5
2.3 GUIDELINES FOR THE DISPOSAL OF SCRAP
PRODUCTS .........................................................................6
2.3.1 DURING SERVICE LIFE .....................................................6
2.3.2 END OF SERVICE LIFE ......................................................6
2.4 PARTS MANUAL .................................................................7
2.5 SALES & SERVICE .............................................................7
3.1 OPERATING SAFETY..........................................................8
3.1.1 OPERATING INSTRUCTIONS 8
3.1.2 SAFETY SIGNS ................................................................... 8
3.1.3 STARTING THE ENGINE ....................................................8
3.1.4 TRANSPORTING ................................................................9
3.1.5 SLOPES ..............................................................................9
3.1.6 BLOCKED CUTTING UNITS ...............................................9
3.1.7 ADJUSTMENTS, LUBRICATION, MAINTENANCE
& CLEANING .......................................................................9
4.1 DIMENSIONS & WEIGHTS ................................................11
4.2 MACHINE SPECIFICATION ................................................12
4.3 HYDRAULIC SPECIFICATION ...........................................12
4.4 CUTTING UNIT SPECIFICATION........................................13
4.5 RECOMMENDED LUBRICANTS ........................................13
4.7 CUTTING PERFORMANCE (AREA) ...................................13
4.8 CUTTING PERFORMANCE (FREQUENCY).......................13
4.9 CERTIFICATES OF CONFORMITY.....................................14
5.1 SAFETY DECALS EC ......................................................... 18
5.1 INSTRUCTION DECALS......................................................18
6.1 CUTTING CYLINDER DRIVE ..............................................20
7.1 DAILY INSPECTION ...........................................................21
7.2 OPERATING PROCEDURE ................................................22
7.3 ATTACHING THE MOWER TO THE TRACTOR ................23
7.4 REMOVING THE MACHINE FROM THE TRACTOR .........25
7.5 MOWING .............................................................................26
7.6 TRANSPORTING ................................................................27
7.7 CUTTING PERFORMANCE ................................................27
7.8 UNBLOCKING CUTTING UNITS ........................................27
7.9 BACKLAPPING ...................................................................27
8.1 MAINTENANCE & LUBRICATION CHART ......................... 29
8.2 LUBRICATION .....................................................................30
8.3 DURING OVERHAUL...........................................................31
8.4 MAINTENANCE ...................................................................32
9.1 HEIGHT OF CUT ADJUSTMENT ........................................33
9.2 CUTTING REEL ADJUSTMENT ......................................... 34
10 QUALITY OF CUT TROUBLESHOOTING ..........................35
10.1 WASHBOARDING ...............................................................35
10.2 MARCELLING .....................................................................36
10.3 STEP CUTTING ..................................................................37
10.4 SCALPING ...........................................................................38
10.5 STRAGGLERS ....................................................................39
10.6 STREAKS.............................................................................40
10.7 WINDROWING..................................................................... 41
10.8 RIFLING OR TRAMLINING .................................................42
10.9 MISMATCHED CUTTING UNITS ........................................42
11.1 GUARANTEE .......................................................................43
SECTION PAGE SECTION PAGE

en-4
2 INTRODUCTION
2.1 IMPORTANT _________________________________________________________
The Ransomes Mounted 214 ia a tractor mounted reel and verticut mower. Using hydraulic systems for cutting
unit drive.
IMPORTANT: This is a precision machine and the service obtained from it depends on the way it is operated
and maintained.
This SAFETY AND OPERATORS MANUAL should be regarded as part of the machine. Suppliers of both new
and second-hand machines are advised to retain documentary evidence that this manual was provided with the
machine.
This machine is designed solely for use as a grass cutting machine operating within the parameters listed in the
specification pages. Use in any other way is considered as contrary to the intended use. Compliance with and
strict adherence to the conditions of operation, service and repair as specified by the manufacturer, also
constitute essential elements of the intended use.
Before attempting to operate this machine, ALL operators MUST read through this manual and make
themselves thoroughly conversant with Safety Instructions, controls, lubrication and maintenance.
Accident prevention regulations, all other generally recognized regulations on safety and occupational medicine,
and all road traffic regulations shall be observed at all times.
Any arbitrary modifications carried out on this machine may relieve the manufacturer of liability for any resulting
damage or injury.
It is important that during the life of the machine wearing and replaceable parts are disposed of in an
environmentally responsible way using the resources available in the country where it is used. There are
guidelines in this manual for the eventual decommissioning of the mower once it has no further use.
Use only Ransomes Jacobsen Genuine spare parts to ensure the control of EC compliance
2006/42/EC
These are the Original instructions verified by Ransomes Jacobsen Limited

en-5
2 INTRODUCTION
2.2 PRODUCT IDENTIFICATION___________________________________________
A Maximum front axle load in Kg (for machines being
driven on the highway)
B Gross weight (mass) in Kg
C MaximumrearaxleloadinKg (for machinesbeingdriven
on the highway)
D Power in Kw
E Date code
F Machine type (Designation)
G Product code
H Product name
J Serial number
SERIAL PLATE LOCATION
The serial plate A is located on the Main Frame in the ??? position.
Kg Kw Kg Kg
West Road
Ransomes Europark
Ipswich IP3 9TT
England
ABCD E
FG
HJ

en-6
2 INTRODUCTION
2.3 GUIDELINES FOR THE DISPOSAL OF SCRAP PRODUCTS ________________
2.3.1 DURING SERVICE LIFE
Used oil, oil filters and engine coolant are hazardous materials and should be handled in a safe and
environmentally responsible way.
In the event of a fluid leak, contain the spill to prevent it entering the ground or drainage system. Local legislation
will dictate how such spills are to treated.
Following the maintenance procedures laid out in this manual will ensure that the impact the machine has on the
local environment is controlled.
When it has been identified that a turf care product has no further functional value and requires disposal, the
following actions should be taken.
2.3.2 END OF SERVICE LIFE
These guidelines should be used in conjunction with applicable Health, Safety and Environmental legislation and
use of approved local facilities for waste disposal and recycling.
• Position the machine in a suitable location for any necessary lifting equipment to be used.
• Use appropriate tools and Personal Protective Equipment (PPE) and take guidance from the technical
manuals applicable to the machine.
• Remove and store appropriately:
1. Batteries
2. Fuel residue
3. Engine coolant
4. Oils
• Disassemble the structure of the machine referring to the technical manuals where appropriate. Special
attention should be made for dealing with ‘stored energy’ within pressurised elements of the machine or
tensioned springs.
• Any items that still have a useful service life as second hand components or can be re-serviced should
be separated and returned to the relevant centre.
• Other worn out items should be separated into material groups for recycling and disposal consistent
with available facilities. More common separation types are as follows:
• Steel
• Non ferrous metals
• Aluminium
• Brass
• Copper
•Plastics •Identifiable
• Recyclable
• Non recyclable
• Not identified
• Rubber
• Electrical & Electronic Components
• Items that cannot be separated economically into different material groups should be added to the
‘General waste’ area.
• Do not incinerate waste.
Finally update machinery records to indicate that the machine has been taken out of service and scrapped.
Provide this serial number to Ransomes Jacobsen Warranty department to close off relevant records.

en-7
2 INTRODUCTION
2.4 PARTS MANUAL ___________________________________________________
As part of the ISO14001principles and in the era of free electronic media, Ransomes Jacobsen Limited no longer
sends a paper parts manual with every product.
If you wish to refer to a parts list for this mower you have four options from which to choose:
Website – www.ransomesjacobsen.com then use the “GENUINE PARTS” tab then the “online parts look-up” tab.
This will give you live access to Parts drawings and lists to aid the identification of spare parts.
Website – www.ransomesjacobsen.com then use the “CUSTOMER CARE” tab followed by the “manuals” tab this
will give you access to a printable version of the parts manual. It can be saved to your computer drive for
reference on the screen or to print all or part of the book as required.
Alternatively by completing the form included in the technical manual pack supplied with the machine, we can
send you either:
• A CD containing an electronic copy of the Parts Book.
• A paper copy of the parts manual.
2.5 SALES & SERVICE ____________________________________________________
A network of authorised Sales and Service dealers has been established and these details are available from
your supplier.
When service attention, or spares, are required for the machine, within or after the guarantee period your supplier
or any authorised dealer should be contacted. Always quote the registered number of the machine.
If any damage is apparent when delivery is made, report the details at once to the supplier of the machine.
It is recommended that the machine number is recorded.
The machine serial number is located on the registration plate.
MACHINE NUMBER:- ___________________________

en-8
3 SAFETY INSTRUCTIONS
3.1 OPERATING SAFETY________________________________________________
This safety symbol indicates important safety messages in this manual. When you see this symbol, be alert to
the possibility of injury, carefully read the message that follows, and inform other operators.
3.1.1 OPERATING INSTRUCTIONS
• Ensure that the instructions in this book are read and fully understood.
• No person should be allowed to operate this machine unless they are fully acquainted with all the controls
and the safety procedures.
• Never allow children or people unfamiliar with these instructions to use this machine. Local regulations
may restrict the age of the operator.
3.1.2 SAFETY SIGNS
• It is essential all safety labels are kept legible, if they are missing or illegible they must be replaced. If any
part of the machine is replaced and it originally carried a safety label, a new label must be affixed to the
replacement part. New safety labels are obtainable from Ransomes Jacobsen dealers.
3.1.3 DRIVING THE MACHINE
• Before moving the machine, check to ensure that all parts are in good working order, paying particular
attention to the security of cutting blades.
• Mow only in daylight or good artificial light
• Stop the blades rotating before crossing surfaces other than grass.
• Remember that some people are deaf or blind and that children and animals can be unpredictable.
• Remove or avoid obstructions in the area to be cut, thus reducing the possibility of injury to yourself and/or
bystanders.
• Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or
their property.
• When the machine is to be parked, storedor left unattended, lower the cutting units.•While mowing, always
wear substantial footwear and long trousers. Do not operate the equipment when barefoot or wearing
open sandals.
• After striking a foreign object Inspect the lawnmower for damage and make repairs before restarting and
operating the equipment.
• If the machine starts to vibrate abnormally, check immediately.
3.1.4 TRANSPORTING
• Ensure that the cutting units are securely fastened in the transport position. Do not transport with cutting
mechanism rotating.
3.1.5 SLOPES
TAKE EXTRA CARE WHEN WORKING ON SLOPES
• Local undulations and sinkage will change the general slope. Avoid ground conditions which can cause the
machine to slide.

en-9
3 SAFETY INSTRUCTIONS
• Keep machine speeds low on slopes and during tight turns.
• Remember there is no such thing as a “safe” slope.
• Travel on grass slopes requires particular care.
3.1.6 BLOCKED CUTTING UNITS
• Stop the engine and make sure all moving parts are stationary.
• Apply brakes and disengage all drives.
• Release blockages with care. Keep all parts of the body away from the cutting edge. Beware of energy in
the drive which can cause rotation when the blockage is released.
• Keep other people away from the cutting units as rotation of one can cause the others to rotate.
3.1.7 ADJUSTMENTS, LUBRICATION, MAINTENANCE & CLEANING
• Stop the engine and make sure all moving parts are stationary.
• Apply brakes and disengage all drives.
• Read all the appropriate servicing instructions.
• Use only the replacement parts supplied by the original manufacturer.
• When adjusting the cutter blades take care not to get hands and feet trapped when rotating blades.
• Make sure that other people are not touching any cutting unit, as rotation of one blade can cause the
others to rotate.
• Replace worn or damaged parts for safety.
• When working underneath lifted parts or machines, make sure adequate support Is provided.
• Do not dismantle the machine without releasing or restraining forces which can cause parts to move
suddenly.
DANGER:
Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.
WARNING:
Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury and prop-
erty damage. It may also be used to alert against unsafe practices.

en-10
3 SAFETY INSTRUCTIONS
CAUTION
Personal Protective Equipment (PPE),
Such As Safety Glasses, Leather Work
Shoes Or Boots, A Hard Hat, Leather
Work Gloves And Ear Protection Should
Be Used Subject To A Local Risk
Assessment Completed By the Owner/
User When Operating the Mowing
Machine to Help Prevent Injury.
Training in All Manual Operations Should
Be Given By A Qualified Person Prior To
Using The Machine For The First Time.
WARNING
Ear Protection Should Be Worn
When Operating Machines With
Operator Ear Noise Levels Above
85dB(A)Leq.
WARNING
To Prevent Serious Injury From Hot, High
Pressure Oil, Never Use Your Hands To
Check For Oil Leaks, Use Paper Or
Cardboard.
Hydraulic Fluid Escaping Under Pressure
Can Have Sufficient Force To Penetrate
Skin. If Fluid Is Injected Into The Skin It
Must Be Surgically Removed Within A
Few Hours By A Doctor Familiar With This
Form Of Injury Or Gangrene May Result.