Thane Fitness FlavorFresh ZJ-1701 User manual

USER’S MANUAL
MODEL No. ZJ-1701
Whole Food Vacuum Juicer

Congratulations on the purchase of your FlavorFresh™ Whole Food Vacuum Juicer! Now making
healthy smoothies, sauces, sorbets and baby food is easy as 1, 2, 3. This product was developed and
manufactured with the utmost care and subjected to numerous quality checks. Thank you for the trust
you place in our brand and we hope that you are extremely satisfied with the FlavorFresh™ Whole Food
Vacuum Juicer. Before operating the unit, please read the instructions completely and carefully and keep
them in case you need to refer to them at a later time.
Thanks again for trusting the FlavorFresh™ brand from Thane™!
Thane™ and its affiliated companies assume no liability for personal injury or property damage resulting from the misuse of
the FlavorFresh™ Whole Food Vacuum Juicer, including the failure to comply with the instructions contained in this User’s
Guide or provided by the manufacturer or distributor of the treated surface.
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING
THIS KITCHEN APPLIANCE!
Thank You
Please note the following recommendations:
• The unit cannot be disposed of in household garbage.
• Usually there are collection points in each municipality for such devices.
• Please check with your local waste disposal authority on the proper disposal of the device.
Electrical and electronic equipment can contain harmful substances that can harm the environment or human
health, and therefore, needs to be recycled.

SAFETY CAUTIONS AND WARNINGS ................................................................................................ 4-5
DIAGRAM AND PARTS LIST..................................................................................................................... 6
BEFORE FIRST USE ................................................................................................................................... 7
INSTRUCTIONS FOR USE:......................................................................................................................... 7
MAIN UNIT INSTRUCTIONS FOR 1L JUICING JAR AND 600ML TO GO CONTAINER.... 7
OPTIONAL ACCESSORY INSTRUCTIONS FOR THE GRINDER SET ...................................... 9-12
CLEANING AND MAINTENANCE ......................................................................................................... 13
TROUBLESHOOTING ................................................................................................................................ 14
!
Contents
14 3
Problem SolutionPossible Cause
The plug doesn’t fit the electrical
socket.
The blade attachment base with
jar/container is not locked into the
Motor Base correctly.
There is too much food/liquid in
the jar/container.
The appliance has been
continuously processing for too
long.
There is too much food in the jar/
container.
• Try a different socket.
• Make sure to plug into a working and properly
installed socket that fits this appliance’s plug.
• Check if the jar/container is properly locked
in place. Vibrations may cause the jar to rotate
slightly out of the locked position and switch off
the appliance.
• Stop the blending process.
• Unplug the unit from the socket.
• Remove the jar/container and remove
some ingredients.
• Stop the blending process.
• Unplug the unit from the socket.
• Remove the jar/container from the Motor Base,
take away some ingredients and try again.
• Stop the blending process.
• Do not exceed 1 minute of continuous processing
for the 1L Juicing Jar and 600ml TO GO Container
(with Quad Blade Attachment).
• Do not exceed 40 seconds of continuous grinding
for the Grinding Jar (with Grinding Blade
Attachment).
• If additional processing is required to achieve
desired texture, try processing or grinding again
until desired results are achieved with short breaks
between each continuous run.
The appliance doesn’t work.
The appliance is working, but
the food is not being sufficiently
processed.
The appliance has an
unpleasant odour with smoke,
and it is getting hot to the
touch.
The blade attachment isn’t
fastened tightly to the jar/
container.
The blade attachment is not
sitting in the sealing silicone ring
properly, or the sealing silicone
ring doesn’t fit in the base.
• Make sure the blade attachment base is properly
attached to the jar/container and try again.
• Check the sealing silicone ring and make sure the
blade attachment base properly ‘sits’ in it so that
it can be attached to the jar/container properly
Liquid is leaking from blade base
Troubleshooting

413
PLEASE READ THIS USER’S MANUAL COMPLETELY AND CAREFULLY.
TO REDUCE THE RISK OF ELECTROCUTION, FIRE, OR INJURY, PLEASE READ
ALL INSTRUCTIONS, SAFEGUARDS, AND WARNINGS IN THIS USER’S MANUAL BEFORE
USING THIS APPLIANCE.
1. Keep this User’s Manual in a safe place for future reference.
2. Verify that the main voltage indicated on the Rating Plate on this appliance corresponds with the voltage
of your electrical outlet.
3. After removing the packaging, make sure that the product is not damaged and that no pieces are missing.
If in doubt, do not use.
4. To avoid danger of suffocation or any other hazards, do not leave packaging (such as plastic bags,
polystyrene, etc.) within reach of children.
5. This appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge.
6. Cleaning and maintenance shall not be performed by children or persons with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge.
7. Keep this appliance and its cord out of reach of children.
8. Close supervision is necessary when the appliance is operated near children to ensure that they do not
play with this appliance.
9. Children shall not play with this appliance.
10. Keep hands, loose clothing and other items away from the rotating blades.
11. Do not use the appliance if the rotating blades are damaged.
12. Do not immerse this appliance (cord and motor housing) in water or any other liquids.
13. Do not operate this appliance with wet hands.
14. This appliance contains no user-serviceable parts. All repairs should only be carried out by a qualified
engineer to avoid hazard. Improper repairs may place the user at risk of harm.
15. Do not operate this appliance if it has malfunctioned, or if it has been dropped or damaged in any way.
16. Do not leave this appliance unattended while it is plugged into an electrical outlet.
17. This appliance must be unplugged from the electrical outlet after use and while any maintenance, such
as cleaning, is being conducted.
18. Always use the appliance on a sufficiently large, stable, dry, heat-resistant surface.
19. Place the unit securely in the center of the counter or work space.
20. Do not place on or near a hot gas or electric burner, or in a heated oven.
21. Ensure that the power cord is kept away from heat or sharp edges that could cause damage.
22. Do not allow the power cord to hang over the edge of work surfaces or tabletops.
23. If the power supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified technician in order to avoid creating a hazardous condition.
24. Never force the plug into an outlet or pull or carry the unit by the cord. Do not use the cord as a
handle, close a door on the cord or pull the cord around sharp edges or corners. Keep the cord away
from heated surfaces.
25. FOR 120V Unit Only: This appliance has a polarized plug (one blade is wider than the other). To
reduce the risk of electric shock, this plug will fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not
attempt to modify the plug in any way.
26. Do not pull the cord in order to remove the plug from an outlet.
27. To avoid power overload, the appliance should not be connected in the same outlet simultaneously
with another high wattage appliance.
28. Do not place this appliance where it can fall or be pulled into water or other liquid.
29. Do not reach for this appliance if it has fallen into water. Unplug immediately!
30. Always unplug this appliance before attempting to move it.
31. Always use both hands when moving the entire unit and make sure to pick it up by the unit’s base.
32. Do not move the appliance while it is in use.
33. Do not use the appliance for any purpose other than its intended use as described in this User’s Manual.
34. This appliance is intended for household use only. It is designed to process normal household quantities
of food and liquids. It is not suitable for continuous or commercial operation. Commercial use of this appliance
voids the manufacturer’s warranty.
Safety Cautions and Warnings
!
WARNING
Cleaning and Maintenance
• Unplug the appliance from the power source before starting the cleaning process.
• None of the parts are dishwasher safe, so use mild detergent and warm water and wash by hand.
• Make sure to clean the containers, blades and lids after each use.
• Always make sure to clean each part thoroughly, especially the items that are used to create vacuum-like
conditions (i.e. remove oxygen). If these parts are not cleaned and dried thoroughly and liquid or food gets
stuck on the inside, their functionality may be affected and they may not create vacuum-like conditions as
intended.
THESE ITEMS ARE THE VACUUM PUMP, MULTIFUNCTION LID, AND FLAT LID
WITH VACUUM VALVE AND THEY SHOULD NEVER BE PUT IN THE DISHWASHER AS THE
HIGH HEAT MAY DAMAGE THE SILICONE PARTS THAT MAKE THE REMOVAL OF OXYGEN
POSSIBLE.
• Never immerse the Motor Base in water to clean it. If need be, wipe the outside of the Motor Base with a
damp cloth.
• After cleaning is done, wipe everything with a dry cloth.
• This appliance contains no user-serviceable parts. Any servicing or repairs should only be carried out by a
qualified engineer or authorized service representative. Improper repairs may place the user at risk of harm
or damage to personal property.
!
CAUTION
THE BLADES ARE VERY SHARP. TO AVOID INJURY, ALWAYS HANDLE WITH
EXTREME CARE.
!
WARNING

5
12
HOUSEHOLD USE ONLY SAVE THESE INSTRUCTIONS
35. This appliance is intended to be used in household and similar applications such as: staff kitchen
areas in shops, offices and other working environments; farm houses; by clients in hotels, motels and
other residential type environments; bed and breakfast type environments.
36. This appliance is for indoor use only. Do not expose the appliance to outdoor weather.
37. Do not use any accessories or attachments with this appliance other than those recommended
by the supplier, as unapproved attachments may cause fire, electric shock or injury.
38. The blades in the Quad Blade Blending Attachment in this appliance are not intended for processing
hard or dry substances as this will dull them.
39. The pulse function is not meant to be used continuously for a prolonged time. It is meant to be
used for a second or two at a time. Improper use of the pulse function can damage this appliance.
40. The manufacturer and distributor are not responsible for any damage caused to this appliance due
to incorrect use.
41. Before placing food in the appliance for processing make sure all wrappers have been removed
(i.e., paper, aluminum foil or plastic) and check the jar/container for foreign objects.
42. Before turning the appliance on, make sure all parts are properly assembled.
43. Avoid contact with moving parts while the appliance is in use to prevent personal injury or damage
to the appliance.
44. To avoid injury, always follow the instructions provided in this User’s Manual when handling the
sharp blades of the attachments.
45. The metal blades are extremely sharp and should be handled with extreme care. Always hold the
blade attachments by their plastic base, away from the sharp edges of the blades, both when
handling and cleaning.
46. Never put your fingers or other objects into the unit opening while it is in operation. If food becomes
lodged in the opening, a scraper may be used, but must be used only when the unit is not running.
When this method is not possible, turn the unit off and disassemble to remove the remaining food.
47. To reduce the risk of injury, never place the blade attachment on the base without the jar/container
and any applicable lids being properly attached.
48. Make sure the jar/container is fastened tightly onto the blade attachment before turning it on.
The unit will not work if the jar/container is not attached properly.
49. Switch off the appliance and disconnect from the power supply before removing the jar/container
from the unit base, changing accessories or getting near moving parts.
50. Always disconnect the appliance from the power supply if it is left unattended and before assembling,
disassembling or cleaning.
51. Warning: Potential injury from misuse. Care shall be taken when handling the sharp cutting blades,
while emptying the jar/container and during cleaning.
52. Never process hot foods and/or liquids, such as soups, with the FlavorFresh™ Whole Food Vacuum
Juicer. Always wait for the food and/or liquid to cool before using the FlavorFresh™ unit to process it.
53. Never run the appliance if it is empty.
54. Do not overfill any of the processing containers past their suggested maximum amount.
55. Take special care when the Vacuum Pump is attached to the jar and avoid liquids (or food) coming
into contact with the inside of the Vacuum Pump. That is why it is very important not to overfill the jar
or shake it while the Vacuum Pump is attached.
56. Always observe the appliance carefully when it is turned on.
57. After use, make sure all the parts that were used are cleaned properly.
58. To avoid personal injury, care must be taken when cleaning any of the attachments that have sharp
blades.
59. None of the attachments and their corresponding lids are freezer, microwave, or dishwasher safe.
Safety Cautions and Warnings
Instructions For Use
8. When the ingredients are processed thoroughly, remove the Grinding Jar from the Motor Base by holding on
to the Motor Base with one hand and turning it in a counter-clockwise direction with the other, then lift (Figure 17).
Doing this will move the arrow on the blade attachment, from being aligned with the ‘ON’ marking, back to being
aligned with the ‘OFF/PULSE’ marking on the Motor Base.
9. Unplug the unit from the power source and enjoy your ground up ingredients.
10.Just like with the To Go Continuer, the Grinder Jar can be used to store the finished product in vacuum-like
conditions. To do this, remove the blade attachment and replace it with the Flat Lid with Vacuum Valve. Then,
use the Vacuum Pump on the Flat Lid with Vacuum Valve to remove oxygen and create vacuum-like storage
conditions (Figure 18).
THE BLADES ARE VERY SHARP. TO AVOID INJURY, ALWAYS HANDLE WITH
EXTREME CARE.
!
WARNING
Figure 17 Figure 18
MAX
MAX

Optional Accessory Instructions for the Grinder Set
Much like the 600ml To Go Container, the Grinder Jar only has one opening which means that you cannot remove oxygen
from its ingredients in order to processes them under vacuum-like conditions, but it can be used to store the finished
product in vacuum-like conditions by removing oxygen with the Vacuum Pump. Here are the instructions for use:
1. Place the Motor Base on a flat surface and make sure the unit is NOT plugged into the power source.
2. Fill the Grinding Jar with your favourite ingredients and make sure not to overfill past the MAX fill line (Figure 13).
This will allow for enough room for the ingredients to be processed thoroughly.
3. Attach the Grinding Blade Attachment to the Grinding Jar by holding the jar with one hand and turning the blade
attachment into place by turning it clockwise. Make sure it is tightly fastened (Figure 14).
4. Plug in the power cord into the power source (Figure 15).
5. Hold the Motor Base with one hand and the Grinding Jar, with blade attachment, with the other. Then, align the arrow
on the Motor Base (located above the “OFF/PULSE” marking) with the arrow on the blade attachment and place the Grinding
Jar, with blade attachment, into the Motor Base (Figure 15).
6. Press down and turn clockwise to lock into place (Figure 16). This will move the arrow on the blade attachment, from
aligning to the ‘OFF/PULSE’ marking, to aligning with the ‘ON’ marking on the Motor Base. Let the unit process the
ingredients for up to 40 seconds*.
*NOTE: If the desired results are not achieved after 40 seconds of grinding, repeat steps 5 and 6 until the desired results
are achieved with brief breaks in between each 40-second continuous run.
7. For tougher ingredients, or in cases when all the ingredients are not mixing right away, use the pulse function by
pressing down on the Grinding Jar a few times and then try grinding again. Repeat this until all the ingredients are ground
properly.
NOTE: Using the pulse function should break up any bigger ingredient pieces or dislodge any ingredients that may get
stuck. The pulse function is not meant to be used continuously for a prolonged time. It is meant to be used for a second
or two at a time
11
6
1. Vacuum Pump
2. Flat Lid
3. 1L Juicing Jar (open at both ends)
4. Quad Blade Blending Attachment
5. Motor Base (250W, 23000rpm)
6. Multifunction Lid
7. 600ml To Go Container (open at one end only)
1
2
3
4
5
7
6
OPTIONAL ITEMS - GRINDING SET PARTS
Grinding Jar Flat Lid With Vacuum
Valve
Grinding Blade
Attachment
Diagram and Parts List Instructions For Use
THE BLADES ARE VERY SHARP. TO AVOID INJURY, ALWAYS HANDLE WITH
EXTREME CARE.
!
WARNING
MAX
MAX
Figure 13 Figure 14
Figure 15 Figure 16
MAX
ON
ON
ON
ON

7
10
Main Unit Instructions: For 1L Juicing Jar and 600ml To Go Container
The 1L Juicing Jar is open on both ends so it can be used for vacuum (and non-vacuum) processing as well as for vacuum
(and non-vacuum) storage. On the other hand, the 600ml To Go Container is open on one end only so it can only be used for
non-vacuum processing as well as vacuum (and non-vacuum) storage.
Instructions for Vacuum (and Non-Vacuum) Processing with 1L Juicing Jar:
1. Place the Motor Base on a flat surface and make sure the unit is NOT plugged into the power source (Figure 1).
2. Attach the Juicing Jar to the Quad Blade Blending Attachment by holding it with one hand and twisting the blade
attachment into place by turning it counter-clockwise. Make sure it is tightly fastened to avoid any liquid leakage (Figure 1).
3. Fill the jar with your favourite ingredients and make sure not to overfill it. There should be room for the ingredients to be
processed thoroughly without making contact with the vacuum pump lid. The processed liquid should not exceed 1L.
4. Next, twist the Vacuum Pump onto the jar by turning it clockwise until it is tightly fastened onto the jar (Figure 1).
NOTE: Always take special care when the Vacuum Pump is attached to the Juicing Jar as liquids should not come into
contact with the Vacuum Pump. This is why it is important not to overfill the jar. Never shake the jar while the Vacuum Pump
is attached as any liquid coming into contact with the inside of the Vacuum Pump can affect its ability to remove oxygen and
create vacuum-like conditions. If the Vacuum Pump does come into contact with liquid. Remove it from the unit, then rinse
and dry it thoroughly before using it again.
5. Hold the jar in place with one hand and use your other hand to press down the Vacuum Pump repeatedly (Figure 2).
Press the Vacuum Pump 5 times or more, as needed. You will feel it getting harder to press down as more and more
oxygen is being removed (Figure 2).
6. Once you are done ‘pumping’ oxygen out of the jar, the last time you press the Vacuum Pump down, hold it down and
twist the top of the Vacuum Pump clockwise until the grooves on the top and bottom part of the Vacuum Pump align.
Check that all the parts are complete and that the unit is not damaged.
Makes sure to wash the blades attachment(s), containers and lids thoroughly before first use with detergent and
warm water. Refer to the cleaning instructions in this manual.
Before First Use
Instructions For Use Instructions For Use
4. Plug in the power cord into the power source (Figure 9).
5. Hold the Motor Base with one hand and the container, with blade attachment, with the other. Then, align the arrow on the
Motor Base (located above the “OFF/PULSE” marking) with the arrow on the blade attachment and place the container, with blade
attachment, into the Motor Base (Figure 9).
6. Press down and turn clockwise to lock into place (Figure 10). This will move the arrow on the blade attachment, from aligning
to the ‘OFF/PULSE’ marking, to aligning with the ‘ON’ marking on the Motor Base. Let the unit process the ingredients for up to 1 minute*.
*NOTE: If the desired results are not achieved after 1 minute of processing, repeat steps 5 and 6 until the desired results are
achieved with brief breaks in between each 1-minute continuous run.
7. For tougher ingredients, or in cases when all the ingredients are not mixing right away, use the pulse function by
pressing down on the container a few times and then try processing again. Repeat this until all the ingredients are
mixing together properly.
NOTE: Using the pulse function should break up any bigger ingredient pieces or dislodge any ingredients that may get stuck.
The pulse function is not meant to be used continuously for a prolonged time. It is meant to be used for a second or two at a
time.
8. When the ingredients are processed thoroughly, remove the To Go Container from the Motor Base by holding on
to the base with one hand and turning it in a counter-clockwise direction with the other, then lift (Figure 11).
Doing this will move the arrow on the blade attachment, from being aligned with the ‘ON’ marking, back to being aligned
with the ‘OFF/PULSE’ marking on the Motor Base.
9. Unplug the unit from the power source and enjoy your juice/smoothie.
10. Your juice/smoothie can be stored in vacuum-like conditions and consumed on the go with the To Go Container.
To do this, remove the blade attachment and replace it with the Multifunction Lid. Then, use the Vacuum Pump
on the Multifunction Lid to remove oxygen and create vacuum-like storage conditions (Figure 12).
THE BLADES ARE VERY SHARP. TO AVOID INJURY, ALWAYS HANDLE WITH
EXTREME CARE.
!
WARNING
THE BLADES ARE VERY SHARP. TO AVOID INJURY, ALWAYS HANDLE WITH
EXTREME CARE.
!
WARNING
Figure 1 Figure 2
Figure 9 Figure 10
Figure 11 Figure 12
ON
ON
ON
ON

89
Instructions For Use Instructions For Use
15. To consume your juice on the go, pour the contents from the 1L Juicing Jar into the 600ml To Go Container.
Seal the container with the Multifunction Lid, place the Vacuum Pump on the Multifunction Lid and use it as instructed
in steps 5 and 6 to remove oxygen and create vacuum-like conditions (Figure 7).
NOTE: If you wish to process your ingredients in the 1L Juicing Jar without vacuum-like conditions (i.e. removing oxygen)
follow the same steps outlined above, but instead of pumping the air out with the Vacuum Pump, either use an already closed
Vacuum Pump as a lid or use the Multifunction or Flat Lids instead to seal the top of the jar during the blending process.
Instructions for Non-Vacuum Processing with 600ml To Go Container:
1. Place the Motor Base on a flat surface and make sure the unit is NOT plugged into the power source (Figure 8).
2. Fill the To Go Container with your favourite ingredients and make sure not to overfill it. There should be room for
the ingredients to be processed thoroughly. The processed liquid should not exceed 600ml.
3. Attach the Quad Blade Blending Attachment to the To Go Container by holding the container with one hand and
twisting the blade attachment into place by turning it clockwise. Make sure it is tightly fastened to avoid any liquid
leakage (Figure 8).
THE BLADES ARE VERY SHARP. TO AVOID INJURY, ALWAYS HANDLE WITH
EXTREME CARE.
!
WARNING
THE BLADES ARE VERY SHARP. TO AVOID INJURY, ALWAYS HANDLE WITH
EXTREME CARE.
!
WARNING
7. Plug in the power cord into the power source (Figure 3).
8. Hold the Motor Base with one hand and the jar, with blade attachment and Vacuum Pump, with the other. Then, align the
arrow on the Motor Base (located above the “OFF/PULSE” marking) with the arrow on the blade attachment and place the jar, with
blade attachment and Vacuum Pump, into the Motor Base (Figure 3).
9. Press down and turn clockwise to lock into place (Figure 4). This will move the arrow on the blade attachment, from aligning to
the ‘OFF/PULSE’ marking, to aligning with the ‘ON’ marking on the Motor Base. Let the unit process the ingredients for up to 1 minute*.
*NOTE: If the desired results are not achieved after 1 minute of processing, repeat steps 8 and 9 until the desired results are
achieved with brief breaks in between each 1-minute continuous run.
10. For tougher ingredients, or in cases when all the ingredients are not mixing right away, use the pulse function by pressing
down on the jar a few times to get the blades moving and then try processing again. Repeat this until all the ingredients
are mixing together evenly.
NOTE: Using the pulse function should break up any bigger ingredient pieces or dislodge any ingredients that may get stuck.
The pulse function is not meant to be used continuously for a prolonged time. It is meant to be used for a second or two at a time.
11. When the ingredients are processed thoroughly, remove the jar from the Motor Base by holding on to the base with one
hand and turning it in a counter-clockwise direction with the other, then lift (Figure 5).
Doing this will move the arrow on the blade attachment, from being aligned with the ‘ON’ marking, back to being aligned
with the ‘OFF/PULSE’ marking on the Motor Base.
12. Unplug the unit from the power source and enjoy your delicious juice.
13. Any leftovers can be stored in the 1L Juicing Jar. To do this, remove the vacuum pump and replace it with the plain Flat
Lid. Make sure it is tightly fastened to avoid any liquid leakage (Figure 5).
14. Flip the jar upside down, then remove the blade attachment and replace it with the Multifunction Lid. After this is done,
the Vacuum Pump can be used on the Multifunction Lid to remove oxygen and create optimal vacuum-like storage
conditions (Figure 6)
Figure 3 Figure 4
Figure 5 Figure 6
Figure 8
Figure 7
ON
ON
ON
ON

Distributed by:
© 2018 Thane IP Limited.
MADE IN CHINA
“Thane”, “FlavorFresh” and related logos and variations are trademarks or registered trademarks,
in Canada and/or other countries, of Thane IP Limited and/or its affiliated companies.
Thane USA, Inc.
Canton OH 44718, U.S.A.
www.thane.com
Thane Canada Inc.
Mississauga ON L4W 5M6,
Canada
www.thane.ca
Thane Direct UK Limited
London EC2Y 9DT, UK
www.thane.tv
Danoz Direct Pty Ltd.
Mascot NSW 2020, Australia
www.danoz.com.au
Operadora Ainoa, S.A.P.I. DE C.V.
Avenida Magnocentro #5 Piso 1
Estado de México C.P: 52760
www.mejorcompratv.com
FlavorFresh_MNL_ENG_R0_180411