THE INSIDE Tailored Platform Bed User manual

BED COMPONENTS
Tailored Platform Bed
ASSEMBLY INSTRUCTIONS
NOTES:
• Open all hardware packets before
proceeding.
• Two people are needed for assembly.
• Additional support legs are in wooden
plank roll box.
*Images may vary from actual product
LIMITED WARRANTY All our items are returnable within 30 days and
guaranteed against defects in construction for one year.
NEED SOME HELP? For any questions contact us via your preferred method.
Mon-Fri 9AM-9PM: Call 909-323-0016 OR E-Mail [e-mail]
YOU WILL NEED:
• Flat head screwdriver
ITEM QUANTITY
A Metal Corners 4
B Metal Side Rail 2
C Metal End Rail 2
D Corner Leg 4
E Center Support Rail 1
F Center Support Leg 1
G Upholstered Side Rail 4
H Upholstered Foot Rail 4
I Wooden Slat Roll 1
I
Wooden Slat Roll
(located in headboard box)

BED HARDWARE
Tailored Platform Bed
ASSEMBLY INSTRUCTIONS
3/4” X 5/16”
BOLTS
x 4
1/4”
BOLTS
x 10
LIMITED WARRANTY All our items are returnable within 30 days and
guaranteed against defects in construction for one year.
NEED SOME HELP? For any questions contact us via your preferred method.
Mon-Fri 9AM-9PM: Call 909-323-0016 OR E-Mail [e-mail]
1/4”
NUTS
x 14
WRENCH
x 1
SMALLER
L WRENCH
x 1
1” X 1/4”
BOLTS
x 5
3/4”
WASHER
x 1
1” X 5/16”
BOLT
x 6
1 X 1/4”
WASHER
x 6
3/4”
WASHER
x 4
LARGER
L WRENCH
x 1
3/4”
SCREW
x 8
(optional)
L BRACKET
x 2
(optional)

1. Place (A) metal corners in
a rectangular shape roughly
the size of your mattress.
STEP 1 - BUILDING THE METAL BED FRAME
Tailored Platform Bed
ASSEMBLY INSTRUCTIONS
4. Carefully attach (D) corner
legs underneath (A) metal
corners using 3/4” x 5/16”
bolts and 3/4” washers.
Tighten using larger
L wrench.
2. Lay (B) metal side rails
and (C) metal end rails into
(A) metal corners to create
the shape of your bed frame.
Snap into place.
3. Secure (B) metal side rails
and (C) metal end rails to
(A) metal corners using
1/4” bolts and 1/4” nuts.
Tighten using small L Wrench
and the wrench.
Note: 1/4” nuts should be on
the inside of the frame.

1. Align holes of (E) center
support rail with holes on
(B) metal side rails. Attach
using 1/4” bolts and 1/4” nuts.
Tighten using the smaller
L wrench and the wrench.
Note: (E) center support rail
attaches underneath
(B) metal side rails.
STEP 2 - CENTER SUPPORT SYSTEM
Tailored Platform Bed
ASSEMBLY INSTRUCTIONS
2. Attach (F) center support
legs to (E) center support rail
using 1” x 1/4” bolts and
3/4” washer. Tighten using
smaller L wrench.
3.Carefully place the
(I) wooden slat roll onto the
bed frame. Attach using
1” x 1/4” bolts and 1/4” nuts.
Tighten with smaller L
wrench and the wrench.
Note: The black band that
holds the slats together
should face the floor.

1. Loosely attach (G, H)
upholstered rails to bed frame
using 1” x 5/16” bolts and
1 1/4” washers.
Note: If (G) upholstered side
rails have an additional hole,
make sure the hole faces
upwards and away from the
(H) upholstered foot rail.
STEP 3 - ATTACHING THE UPHOLSTERED RAILS
Tailored Platform Bed
ASSEMBLY INSTRUCTIONS
2. Push (G) upholstered side
rails toward (H) upholstered
foot rail to eliminate any gaps.
Tighten (G) upholstered side
rails first, then (H) upholstered
foot rail using flat head
screwdriver.
3. (OPTIONAL)
To reinforce stability of
(G, H) upholstered rails, use
a phillips screwdriver to attach
L brackets using 3/4” screw.
Note: this requires screwing
3/4” screws directly into the
upholstered side rail.

Headboard
HARDWARE INCLUDED:
1” X 1/4”
BOLTS
x 4
5/8” X 5/16”
BOLTS
x 4
1 1/4”
WASHER
x 12
1/4”
NUTS
x 4
Note: You will need a flat head screwdriver and a wrench for assembly.
(A) HEADBOARD
Note: actual headboard may
look different than illustration.
(B) HEADBOARD LEGS
x 2
HEADBOARD COMPONENTS
ASSEMBLY INSTRUCTIONS
LIMITED WARRANTY All our items are returnable within 30 days and
guaranteed against defects in construction for one year.
NEED SOME HELP? For any questions contact us via your preferred method.
Mon-Fri 9AM-9PM: Call 909-323-0016 OR E-Mail [e-mail]

Headboard
ASSEMBLY INSTRUCTIONS
1. Place (A) headboard face down on a
flat surface. Place (B) headboard legs
on the back of (A) headboard, aligning
the slots of the legs with the holes of the
headboard.
Note: Make sure the “Out” sticker on
each (B) headboard leg is facing the
correct way.
2. Attach (B) headboard legs to
(A) headboard using 5/8” x 5/16”
bolts and 1 1/4” washers.
Tighten with a flat head screwdriver.
STEP 1

Headboard
ASSEMBLY INSTRUCTIONS
STEP 2
Attach the assembled headboard to
your bedframe using 1 x 1/4” bolts,
1 1/4” washers and 1/4” nuts.
Tighten with a flat head screwdriver
and wrench.
Note: The height of your headboard
can be adjusted by loosening
the (H1) bolts and shifting the
(A) headboard up or down.