Teknik Canyon Lane 5425302 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS
IMPORTANT SAFETY
INFORMATION.
PLEASE READ AND KEEP
FOR FUTURE REFERENCE.
TV Unit
Canyon Lane | Model 5425302
Smart stand
for the idiot
box.

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
WARNING
!
Table of Contents Assembly Tools Required
15-1/2"
15-1/2"
54"
54"
Skip the power trip.
This time.
3
4
5-18
19-21
22-24
25-26
27
70 lbs.
70 lbs.
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with flat panel televisions weighing less than 70 pounds. Never use with a TV that weighs more .
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• Be sure to apply the warning label as instructed later in the assembly. The label provides important safety related information.
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A TOP (1)
B STOP MOLDING (1)
C LEFT END (1)
D LEFT UPRIGHT (1)
E RIGHT UPRIGHT (1)
F RIGHT END (1)
G BOTTOM (1)
H BASE (1)
J LEG (4)
K FOOT (2)
L CENTER BACK (1)
M LEFT BACK (1)
N RIGHT BACK (1)
O SMALL ADJUSTABLE SHELF (2)
P LARGE ADJUSTABLE SHELF (1)
Q LEFT DOOR (1)
R RIGHT DOOR (1)
Page 3
A
B
C
D
E
F
G
H
L
M
N
O
P
Q
R
O
J
K
J

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
HIDDEN CAM - 16
1CAM SCREW - 8 2WOOD DOWEL - 19 3
SHELF PIN - 12
4
L-WRENCH - 1
10
BLACK 3/4" MACHINE SCREW - 4
13
BLACK 1-9/16" PAN HEAD SCREW - 8
11 BLACK 1-3/16" HEX HEAD SCREW - 2 12
BLACK 1/2" HEX HEAD SCREW - 12
14
FELT DISC - 2
6
PULL - 2
8
(Refer to Step 12 for proper
location and application)
WARNING LABEL - 1
9
522,68 22,68
70 lbs. 31,75 kg 31,75 kg
Page 4
BI-CAM DOWEL - 4
5
BLACK 1/2" PAN HEAD SCREW - 30
15
APPLIQUE CARD - 2
7

Page 5
Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW
Hidden CamHidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
Cam Screw
Turn a CAM SCREW into the part.
Insert the CAM SCREW into the HIDDEN CAM.
Tighten the HIDDEN CAM.
1
2

Step 1
Page 6
å Assemble your unit on a carpeted floor or on the empty carton to avoid
scratching your unit or the floor.
å Turn eight CAM SCREWS (2) into the TOP (A) and STOP MOLDING (B).
å Push eight HIDDEN CAMS (1) into the TOP (A) and STOP MOLDING (B).
å NOTE: Be sure the HIDDEN CAMS insert completely down into the holes.
å Insert three WOOD DOWELS (3) into the STOP MOLDING (B).
3
2
1
Arrow
1
Arrow
2
A
B
2

å Insert four BI-CAM DOWELS (5) into the TOP (A). Tighten
four HIDDEN CAMS while keeping the DOWELS centered
in the CAMS.
å Fasten the STOP MOLDING (B) to the TOP (A). Tighten
four HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the STOP
MOLDING insert into the TOP.
Step 2
Page 7
5
A
B
Just think. The sooner
you do this, the sooner
you do something else.
1
2

å Push eight HIDDEN CAMS (1) into the ENDS (C and F)
and UPRIGHTS (D and E).
å Insert sixteen WOOD DOWELS (3) into the edges of the
ENDS (C and F) and UPRIGHTS (D and E).
Step 3
Page 8
3
CD
EF
Arrow
1
Arrow
1
(16 used)

å Fasten the ENDS (C and F) and UPRIGHTS (D and E) to the TOP (A)
and STOP MOLDING (B). Tighten eight HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the ENDS and UPRIGHTS
insert into the TOP.
Step 4
Page 9
A
B
D
E
F
Surface with
HIDDEN CAMS
Finished edge
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
C
Surface without
HIDDEN CAMS

å Fasten the BOTTOM (G) to the ENDS (C and F) and UPRIGHTS (D
and E). Use eight BLACK 1-9/16" PAN HEAD SCREWS (11).
å NOTE: You should start each SCREW a few turns before completely
tightening any of them.
å NOTE: Be sure the WOOD DOWELS in the ENDS and UPRIGHTS
insert into the BOTTOM.
Step 5
Page 10
D
E
F
CG
BLACK 1-9/16" PAN HEAD SCREW
(8 used in this step)
11
Groove