Home Decorators SOUTHPORT TW-18401TY User manual

Home Decorators
Collection
HDC# 08053 MFG# TW-18401TY
SOUTHPORT 4 DOOR SIDEBOARD 30°Hx58"W x14.5"D
ASSEMBLY INSTRUCTIONS
Note: Before assembly, please be sure to work on a soft,
flat surface to avoid any damage to the finish.
Made In China
P 1/8

BEFORE ASSEMBLY
IMPORTANT NOTE: READ CAREFULLY BEFORE ASSEMBLY TO PREVENT DAMAGE TO PARTS. Following
instruction listed below in the proper sequence as numbered to assure fast, easy and correct assembly.
ASSEMBLY TOOLS REQUIRED
OP” о,” L
"+"Screw driver "-" Screw driver Rubber Mallet Electric drill
WOODEN DOWEL INSTALLATION PROCEDURE
(1)
(2)
3)
]
(1)
FILL
HOLE
1/4
FULL
OF
GLUE.
(2)
GENTLY
TAP
DOWEL
INTO
HOLE
шесі
WITH RUBBER MALLET OR USE HAND Б
PRESS IN. |
DO NOT USE HAMMER
(3)
WIPE
AWAY
EXCESS
GLUE.
=
3”
HIDDEN CONNECTOR ASSEMBLY TECHNIQUES FOR LOCK NUT & LOCK PIN
1 SET INCLUDES: (C) CAM-LOCK 1PC. (A) CAM BOLT 1PC.
TOOL NEEDED: “+” SCREW DRIVER
STEP 1: SCREW CAM BOLT (A) ONTO PRE-SET PLASTIC NUT ON PANEL. USE A “+” SCREW-DRIVER FOR
TIGHTENING. ATTENTION: DO NOT OVER TIGHTEN THE CAM BOLT (A).
STEP 2: ATTACH BOTH PANELS, MAKE SURE YOU HAVE INSERTED THE CAM BOLT TO THE VERY DEPTH OF THE
HOLE
WITH
RUBBER
MALLET
GENTLY,
CAUTION:
DO
NOT USE
HAMMER.
THEN
INSERT
CAM-LOCK
(C)
INTO PRE-DRILLED HOLE ON PANEL, MAKE SURE THE ARROW ON CAM-LOCK (C) SET IN PANEL POINT
TOWARD THE HOLE INTO WHICH THE CAM BOLT (A) HAS BEEN INSERTED AND INSERTED THE CAM-LOCK
(C)
TO
THE
VERY
DEPTH
OF
THE
HOLE.
STEP 3: ROTATE THE CAM-LOCK (С) CLOCKWISE TO SECURE CAM BOLT (A) BY TIGHTENING WITH A “+”
SCREWDRIVER.
DETAIL STEP PLEASE SEE THE BELOW PICTURE.
P 2/8

VERTICAL CONNECTION
HORIZONTAL CONNECTION
(0 l (A)
(2)
(1)
{ (А)
(2)
Swe 274 ч
(3) (4) (3) (4)
(C)
А
(8,
©
Се)
”
(5) (5)
A
PARTS LIST
DOOR 2 PCS DOOR 2 PCS TOP PANEL 1 PC
| А В С
BOTTOM PANEL 1 PC ACROSS PANEL 1 PC LEFT SIDE PANEL 1 PC
22
ЕС
|
D E F
RIGHT SIDE PANEL 1 PC MIDDLE VERTICAL SHELF 2 PCS
PANEL 1PC
G H I
BACK PANEL 1 PC LEG 1 PC
a (0)
oS
J K L
P 3/8

HARDWARE LIST
WOOD DOWEL CAM BOLT ROUND HEAD BOLT KNOB
20 PCS САМ-ГОСК FLAT WASHER ROUND HEAD BOLT
VELVET HOLE COVER |7 SETS 4 SETS
= „= :
D ae % Оо) роо aa
HINGE HINGE MAGNET LOCK IRON SLICE
ROUND HEAD SCREW ROUND HEAD SCREW | ROUND HEAD SCREW | FLAT HEAD SCREW
4 SETS 4 SETS - 2 SETS 4 SETS
с”
ҳу
s9
Z
9
BA
|
o © 7 б 9 X о (8)
SHELF HOLDER ROUND HEAD SCREW TILTING PREVENT HARDWARE ALLEN KEY GLUE
8 PCS 30 PCS 1 PC 1 PC
«Эр
"р
рр
„Орр
ws
ov
@ ур, ру = @
(9) (10) (11) (12) (13)
STEP 1: ASSEMBLE ACROSS PANEL (E) ON BOTTOM PANEL (D)
e FILL RELEVANT HOLES 1/4 FULL OF GLUE, INSERT WOOD DOWEL
(1) INTO THESE HOLES. (DETAILS SEE WOODEN DOWEL
INSTALLATION PROCEDURE ON PAGE 2).
• USE ROUND HEAD BOLT & FLAT WASHER (3) TO ATTACH ACROSS
PANEL (E) AND BOTTOM PANEL (D) TOGETHER BY ALLEN KEY (12).
STEP 2: ASSEMBLE LEG (K)
“ ASSEMBLE LEG (К) ON BOTTOM PANEL (D).
P 4/8

STEP
3:
ASSEMBLE
MIDDLE
PANEL
(Н)
e FILL RELEVANT HOLES 1/4 FULL OF GLUE, INSERT WOOD DOWEL (1) INTO THESE HOLES.
(DETAILS
SEE
WOODEN
DOWEL
INSTALLATION
PROCEDURE
ON
PAGE
2).
e USE CAM BOLT & САМ LOCK (2) TO ASSEMBLE MIDDLE VERTICAL PANEL (Н) AND BOTTOM PANEL
(D)
TOGETHER.
(PLEASE
PAY
ATTENTION
TO
THE
UPWARD
LABEL
TO
MAKE
SURE
IT
IS
ASSEMBLED
CORRECTLY) .
e USE VELVET HOLE COVER (2) TO COVER THE CAM-LOCK HOLES AS SHOWN.
STEP 4: ASSEMBLE SIDE PANEL (Е & G)
“ FILL RELEVANT HOLES 1/4 FULL OF GLUE, INSERT WOOD DOWEL (1) INTO THESE HOLES.
(DETAILS SEE WOODEN DOWEL INSTALLATION PROCEDURE ON PAGE 2).
e USE ROUND HEAD BOLT & FLAT WASHER (3) TO ATTACH SIDE PANEL (Е & G) AND BOTTOM PANEL
(D) TOGETHER.
| UP
Р 5/8

STEP
5:
ASSEMBLE
KNOB,
HINGE,
IRON
SLICE
STEP
6:
ASSEMBLE
MAGNET
LOCK
(7)
e
USE
ROUND
HEAD
BOLT
(4)
TO
ATTACH
KNOB
(4)
ONTO
e
USE
ROUND
HEAD
BOLT
(7)
TO
ATTACH
MAGNET
LOCK
(7)
DOOR
(A
&
B).
ONTO
TOP
PANEL
(C).
e USE ROUND HEAD SCREW (5) & (6) TO FIX HINGE
(5) & (6) ONTO DOOR (A & B) AS SHOWN.
e
USE
FLAT
HEAD
SCREW
(8)
TO
ATTACH
IRON
SLICE
(8)
ONTO
DOOR
(A
&
B).
B
(6)
(8)
КА
|)
(6) (5)
STEP 7: ASSEMBLE ТОР PANEL (С) AND DOOR (A 6 В)
e FILL RELEVANT HOLES 1/4 FULL OF GLUE, INSERT WOOD DOWEL (1) INTO THESE HOLES. (DETAILS SEE WOODEN DOWEL
INSTALLATION PROCEDURE ON PAGE 2).
e USE CAM BOLT & CAM LOCK (2) TO ASSEMBLE TOP PANEL (С) AND MIDDLE VERTICAL PANEL (Н) & SIDE PANEL (Е & G)
TOGETHER, AND INSERT THE HINGE OF THE DOOR (A & B) INTO THE RELEVANT HOLES ON THE TOP PANEL (C) AND
BOTTOM PANEL (D) AS SHOWN.
e USE THE VELVET HOLE COVER (2) TO COVER THE CAM-LOCK HOLES AS SHOWN.
val
OU таз)
1 е /
(Di
ға)
Р 6/8

STEP 8: PLACE SHELF (1)
e INSERT SHELF HOLDERS (9) INTO THE HORIZONTAL HOLES INSIDE OF SIDE FRAME (Е & G) AND
MIDDLE VERTICAL PANEL (H), THEN PUT SHELF (I) ON THE SHELF HOLDERS.
Хх
STEP 9: ASSEMBLE BACK PANEL (J)
e USE ROUND HEAD SCREW (10) TO ATTACH BACK PANEL (J) ON THE BACK OF PRE-ASSEMBLED UNIT.
NOTE: BEFORE YOU ASSEMBLE BACK PANEL, PLEASE MAKE SURE THE 2 SIDE PANELS HAVE EVEN GAP
BETWEEN THEM. IF UNEVEN, SHIFT THE SIDE PANELS EVENLY SPACED, THEN ATTACH BACK PANEL.
ф
P 7/8

STEP
10:
ASSEMBLE
PREVENT
DEVICE
(11)
e USE ELECTRIC DRILL TO DRILL 4 SMALL HOLES ON THE DESIRED LOCATION OF WALL, INSERT
4 GECKOS INTO THE 4 HOLES BY RUBBER MALLET, USE TWO LONG SCREWS TO ATTACH ONE
PLASTIC SLICE ONTO WALL, THEN USE TWO SHORT SCREWS TO ATTACH ANOTHER PLASTIC SLICE
ON THE BACK OF PRE-ASSEMBLED PRODUCT.
e USE THE PLASTIC ROPE TO LINK THE PRODUCT AND WALL TOGETHER.
P 8/8