The Modern Fan Company Ball Flush User manual

THE MODERN FAN COMPANY
Customer Service
M-F 8am - 4pm (PST)
(ph) 888.588.3267
www.modernfan.com
(1) Remove and identify contents of carton.
Ball Flush Fan- Installation instructions
Should you have any questions or difficulty installing your new fan,
please contact Modern Fan Co. customer service immediately.
Note: Power supply must be turned off prior to any contact with electrical wires. It is
recommended that a licensed electrician be hired to install your ceiling fan.
Ball Flush
optional
control
balancing kit
ceiling plate
blades
fan body
hardware
package
(2) Place fan on work area, bottom side up.
Remove bottom dome by rotating counterclockwise.
You may need to hold the upper portion of the fan
body with one hand as you are removing
(unthreading) the bottom dome with the opposite
hand.
(3) Carefully insert blades into rotor slots, and using screws
from hardware package, secure blades to rotor. The
counter sink screws (“blade center screws”) are for the single
blade hole outside the rotor and the pan head screws
(“blade holder screws”) are for the two holes inside the rotor
area for each blade.

Trim ring
(4) If your fan was ordered/configured with a light, identify all parts as shown here
and follow steps (a) through (g). Otherwise, proceed to step (5).
Adapter plate
LED Cover
LED Board
Glass diffuser
Bridge connector
Light kit hardware
(a) Remove switch housing screws to access
light kit leads. Set the screws aside for
reinstallation at step (c). Note: Depending on
when you fan was produced, the 2-pin
connector may already be installed. If so, skip
to step (d).
(d) Attach trim ring using small button head
screws included in hardware pack.
(b) Join bridge connector with light kit lead
wires from fan. Note: Skip this step if 2-pin
connector is already present.
(c) Route 2-pin end of connector out of center
hole on switch housing and carefully reinstall
switch housing with screws from step (a). Be
sure that all wires are inside the outer edges
of the switch housing. Note:Skip this step if 2-
pin connector is already present.
(e) Align holes on adapter plate with holes on
switch housing. Using countersink screws
included with hardware pack, secure adapter
plate to switch housing.
(f) Position and insert 2-pin connector into
terminal near center hole of LED board.
Position LED board flat on adapter plate so
that three cutouts are positioned over
attachment holes. Feed any excess wire
back into switch housing.
(g) Position LED cover over LED board so
that attachment holes are aligned with
cutouts and holes in adapter plate. Using
three additional, small pan head screws
included with hardware pack, secure LED
cover and LED board to adapter plate.

(5) Using the existing screws from your junction box,
or the machine screws from the hardware package,
secure the ceiling plate to ceiling junction box. The
electrical wires must be accessible through the hole
in the center of the ceiling plate.
(6) Secure suspension cable loop around the hook
inside the top of the fan body.
(7) Lift fan body and carefully align collar with ceiling
plate. Tabs on ceiling plate should seat into
channel on inside of fan collar. Rotate fan so that
set screw holes on fan body align with set screw
holes on ceiling plate.
(8) Insert and firmly tighten three set screws. Hint-
do not tighten down set screws until all three are
partly screwed in.
suspension cable
and loop
hook
With fan safely suspended by cable, make wire
connections with wire nuts included in hardware
package as described in the control installation
instructions. If using the optional #003, #004 or
#005 control, the receiving unit should be
connected at this time and placed inside the top of
the fan.
set screw hole
(9) Your fan is reversible for summer and winter
operation. The reverse switch is located just inside
the labeled opening on the upper motor housing.
The LEFT position is for summer and the RIGHT
position is for winter.

(10) Reinstall bottom dome or glass diffuser if your fan has
a light kit. Rotate in the clockwise direction until dome or
diffuser comes to a stop.
(12) The rotor and motor of your fan have been dynamically balanced at the factory.
In addition, the blades have been matched to the nearest gram to ensure a well
balanced ceiling fan. Furthermore, a blade balancing kit has been included with your
fan. Please refer to the instructions packaged with the balancing kit should your fan
require additional balancing.
(11) Install wall control as described in the control installation instructions (unless you
are using a handheld remote control only).
709 Washington Street • Ashland, OR 97520 • (tel) 888.588.3267 • (e) [email protected]
w w w . m o d e r n f a n . c o m