Elba ETWF-C3012RC(SV) User manual

For The Warranty Terms & Conditions, Please Refer To Warranty Certificate
Owner’s Manual
Please read this manual carefully
before operating your set.
Retain it for future reference.
Record model number and serial
number of the set.
See the label attached on the set
and quote this information to your
dealer when you require service.
TOWER FAN
MODEL: ETWF-C3012RC(SV)

2
REMOVE ALL PACKING MATERIALS FROM THIS PRODUCT BEFORE
USING IT. THIS APPLIANCE MUST BE INSTALLED ON A FLAT SURFACE.
PLEASE ENSURE THE ELECTRIC SUPPLY TO THIS APPLIANCE IS
DISCONNECTED BEFORE INSTALLING.
Please read this instruction carefully. It is advisable to keep this instruction
manual in a safe place for future reference.
SAFETY PRECAUTIONS
1. Keep electrical appliances out of reach from children. Do not let them to
operate the appliances without supervision.
2. To protect against the risk of electrical shock, do not immerse the product,
cord or plug into water or any other liquids.
3. This product is for household, non-commercial and indoor use only.
4. This product is not intended for use by person (including children) with
reduced physical, sensory or mental capabilities unless they have been
given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
5. If the power cord or plug is damaged, it must be replaced by the service
centre or a qualified service technician to avoid hazard.
WARNING - to reduce the risk of fire, electrical shock or injury to persons or
property, please read and follow below instructions carefully:
Always operate the product from a power source of the same voltage,
frequency and rating as indicated on the product identification marking.
Do not operate this product if it has malfunctioned, damaged cord or plug
or appears damaged in any way. Return the complete product to the place
of purchase for inspection, repair or replacement.
This product should not be used in the immediate vicinity of water, such as
bathtub, washbowls, swimming pool etc. where the likelihood of immersion
or splashing could occur.
Always switch off and unplug the plug from outlet when not in use, before
assembling or disassembling parts and before cleaning. Fully assemble
the set before operating.
Avoid contacting with moving parts. Do not insert any object through the
guard when the set is operating.
Do not cover the guard or operate in close proximity to curtains, etc.

3

4
PRODUCT DESCRIPTION
1. On/Off Button
2. Speed Setting
3. Oscillation Setting
4. Timer Control Setting
5. Control Panel
6. Remote Controller
7. LED Function Display
8. Carrying Handle
9. Remote Controller Storage
10. Air Flow Direction Adjuster
11. Oscillation Grid
12. Fan Body
13. Cord Storage
14. Air Inlet Grid
15. Power Cord with Plug
16. Fan Base
ASSEMBLY INSTRUCTION
1. Unpack the appliance and remove all packaging materials.
2. Before using the appliance for the first time, make sure the mains voltage
correspond to the unit’s operating voltage.
3. Place the appliance on a flat dry surface and provide that furniture or
room objects do not block the air inlet grid (14).
4. Connect the plug (15) into the main socket and switch on the power. The
power indicator near the on/off button (1) will lights up and you will hear a
sound signal.

5
OPERATING INSTRUCTIONS
NOTICE: To avoid damage to the unit, ensure the product is fully assembled
before plugging it into an electrical outlet.
1. Press the on/off button (1), the room temperature will be shown on the
display (7) and the sensor button (2, 3, and 4) illumination will light up.
2. The fan will be switched on for 3 seconds at high speed mode, and then
automatically switched to the low speed mode.
3. Press the on/off button (1) again to turn the unit into standby mode.
Note: The room temperature is shown either in Celcius (ºC) or in Fahrenheit (ºF)
degrees. Press and hold the on/off button (1) for 5 seconds to change the
measurement unit.
4. Select the speed by touching sensor button (2) on the unit or the remote
controller. The following modes will be indicated on the display:
“L” – Low Fan Speed
“M” – Medium Fan Speed
“H” – High Fan Speed
“” –Breeze Mode (Quiet wind with speed lower than “L” mode.)
5. To set the oscillation of the unit, touch the sensor button (3) on the unit or
the remote controller. Touch again to stop the oscillation.
6. Set the automatic switch off timer by touching the sensor button (4)
repeatedly from 1 to 9 hours with every one hour interval. The unit will
turn off automatically after the timer is set.
7. Adjust the air flow vertical direction by moving the air flow direction
adjuster (10).
USING THE REMOTE CONTROLLER
1. The function on the remote controller is identical to the control panel.
2. Remove the battery compartment lid of the remote controller (6) and
insert 2 “AAA” batteries according to the polarity.
3. Close the battery compartment lid tightly.
4. For easy storage, place the remote controller at the remote controller
storage (9) at the rear of the appliance.

6
CLEANING AND MAINTENANCE
WARNING: To avoid the risk of electrical shock, always ensure the product is
unplugged from the electrical outlet before relocating or cleaning it.
1. Wipe the body of the appliance with a slightly damp cloth and then wipe it
dry. If necessary, use small amount of soft detergent.
2. Do not use solvents or abrasive cleaning agent for cleaning the appliance.
3. Do not immerse the appliance into water or any other liquid to avoid
electric shock.
4. You can use a vacuum cleaner with corresponding attachment to clear
the grid of the air inlet
MAIN SPECIFICATION
Voltage : 220-240V/50Hz
Rated Power: 120W
Timer : 9 Hours
Height : 30.3 in
Product Dimension: 250 (W) x 313 (D) x 770 (H) mm

7