Theben theLuxa S360 WH User manual
1
theLuxa S360 WH 1010510
theLuxa S360 BK 1010511
309699
Motion detector
EN
1. Essential safety instructions
Danger of death through electric shock or fire!
Installation should only be carried out by a pro-
fessional electrician!
WARNING
•The device conforms with EN 60669-2-1 when correctly
installed
•IP 55 in accordance with EN 60529
Designated use
•Motion detector for automatic lighting control dependent
on presence and brightness
•Suitable for installation on external walls or ceilings
•Suitable for entrances, garages, gardens, corridors, parks,
etc.
•Only intended for installation outside of arm‘s reach
Disposal
Dispose of the motion detector in an environmentally sound
manner (electronic waste)
2. Description
3 potentiometers
for setting time
(min) and bright-
ness (lux) and
sensitivity (Meter)
Motion detector
with sensor head
3. Connection
WARNING
Danger of death through electric shock!
Disconnect power source!
Cover or shield any adjacent live components.
Ensure device cannot be switched on again!
Check power supply is disconnected!
Earth and bypass!
The device can be manually activated with a circuit breaker.
After releasing the button (return of power) the device swit-
ches on (for at least 40 secs or for the time set on the device).
4. Installation
If applicable, use optional corner bracket (9070902,
9070903) or optional spacer frame (9070906, 9070907) for
exible installation as well as cable insertion from side or
top/bottom.
230V
Disconnect power source.
2
Make marks for the holes on the wall (with en-closed drill
template/base).
Drill holes.
Ø 6 mm
60mm
Feed cable through the seal of the base.
Fasten base (and spacer frame) to the wall.
OR
brown
brown
Phase
Switched
phase
Neutral
conductor
Neutral
conductor
Earthing
conductor
Earthing
conductor
blue
blue
green/yellow
Connect the individual wires to the appropriate terminal.
Tighten screws.
Click!Click!
Plug motion detector into base and click in.
Connect motion detector to power supply.
Dismantling
Using the screwdriver, carefully loosen the snap-in hook at
the side and pull the device forward.
Installation instructions
As the detector reacts to variations in temperature, avoid the
following situations:
Do not direct motion detectors at objects with highly reec-
tive surfaces such as mirrors etc.
Do not install motion detectors near heat sources such as
heating outlets, air conditioning systems, lamps etc.
Do not direct the motion detector at objects that turn in the
wind such as curtains, large plants etc.
Take account of motion direction during test run.
10
20
30
40
40
10
20
30
40
40
10
20
30
40
40
5 m
16 m
360°
•Recommended installation height: 2 – 4 m
•Crosswise detection area: 16 m (crosswise to the detector)
•Frontal detection area: 5 m (in front of the detector)
•Detection angle: 360°
5. Direction test and alignment
The walk test is used to test the detection range and to res-
trict it if necessary.
Set the potentiometer time (min) to test.
The motion detector now only reacts to movement (indepen-
dent of brightness).
Crosswise to the detection area. After the motion detector
has detected a movement, it switches on for 2 s.
Note direction of motion during the test.
3
0
2
Sec
2 sec
Test
Min
Align motion detector with sensor head
The sensor head can be turned by 45° downwards and 90°
upwards and by 90 ° to the left and right.
90°
45°
90°
90°
6. Use screens
Use supplied screen to adjust the motion detector to
desired detection area.
Remove the required section from the screen using pliers.
Then place on the lens and screw in.
7. Setting
The motion detector has 3 potentiometers underneath
for setting the time (Min), brightness (Lux) and sensitivity
(Meter).
Meter
Min
Lux
Set brightness (lux)
You can set different brightness values (lux) with the
potentiometer.
If you want to change the preset brightness (15 lux default)
Set potentiometer to desired brightness (5 – 1000 lux).
teach-in 1000 Lux
5 Lux 500 Lux
7 Lux 100 Lux
10 Lux
15 Lux
50 Lux
15 Lux
or want a specic brightness value to be learned using the
teach-in function
At the desired brightness set the potentiometer to .
The value will be learned after 15 s.
Leave potentiometer at position .
Set time (min)
If the motion detector detects no further movement, it swit-
ches off after the set time.
If you want to change the preset time (2 min default)
Set potentiometer to desired time (1 s – 20 min).
Min
test 20 min
1 s 15 min
30 s 10 min
1 min 2 min 5 min
2 min
If you want to use the pulse function (e.g. for a staircase light
time switch)
Set potentiometer to position
Min
. The motion detector
is switched on for < 1 s, then off for 9 s. If it detects a
movement again, it switches on again for 1 s.
Set sensitivity (Meter)
You can reduce the sensitivity; this also reduces the detection
range.
Set Potentiometer Meter to the desired sensitivity.
Meter
Max. sensitivity
4
8. Technical data
• Operating voltage: 230 V AC, +10 % –15 %
• Frequency: 50 Hz
• Standby: 0,5 W
• Detection angle: 360°
• Detection area: crosswise: max. 16 m,
frontal: max. 5 m
• Installation height: 2 – 4 m
• Exit-On function: yes
• Brightness setting range: 5–1000/∞ lux
• Switch-off delay: 5 s – 20 min
• Permissible ambient temperature: –25 °C to +45 °C
• Protection class: II
• Protection rating: IP 55 in accordance with
EN 60529
• Switching capacity: 10 A (cos ϕ= 1)
6 A (cos ϕ= 0.6)
3 AX (cos ϕ= 0.3)
• Min. switching capacity: 10 mA
• Switching contact: μ-Contact 230 V AC
• LED lamps <2 W 25 W
• LED lamps >2 W <8 W 90 W
• LED lamps >8 W 100 W
• Incandescent and halogen lamp load: 2300 W
• Low-voltage halogen lamps: 2300 VA
• Fluorescent lamps (low-loss series devices):
uncorrected: 400 VA
Series corrected: 400 VA
Parallel-corrected: 400 VA (42 μF)
• Fluorescent lamps (electronic ballast): 600 W
• Compact uorescent tubes
(electronic ballast): 150 W
Service address
Theben AG
Hohenbergstr. 32
72401 Haigerloch
GERMANY
Phone +49 7474 692-0
Fax +49 7474 692-150
Hotline
Phone +49 7474 692-369
Fax +49 7474 692-207
Addresses, telephone numbers etc.
www.theben.de
This manual suits for next models
1
Table of contents
Other Theben Accessories manuals
