Thermador MT27 User manual

Page 1
Installation Instructions
for
Thermador®Microwave MBY
(Sold Separately)
Built-InTrim Kits • Models MT27 & MT30
IMPORTANT: Local codes vary. Installation, electrical connections, circuit breakers
and grounding must comply with all applicable codes. Save these
instructions for the Local Electrical Inspector's use.
INSTALLER: Please leave these Installation Instructions with this unit for the
owner.
OWNER: Please retain these instructions for future reference.
WARNING: Disconnect power at the breaker before installing.
Please Read this entire manual before proceeding:
Ta b le of Contents
Step 1: Unpacking ............................................. 2
Step 2: Cabinet Preparation ........................... 3
Step 3: Electrical Installation ........................... 3
Step 4: Installing the Trim Kit.......................... 4
Step 5: Installing the Microwave Oven ......... 5
7
0
89
45 6
123
SENSOR
REHEAT
SENSOR
COOK
POWER
LEVEL
POP
CORN
TIMER CLOCK
MORE
/LESS
QUICK
MIN
FUNCTION
KEY
SERVING
/WEIGHT
KEEP
WARM
TURBO
DEFROST
STOP/RESET START

Page 2
Step 1: Unpacking
A. Microwave Oven Model MBY (Sold Separately)
Open the box and carefully remove fillers and all packing material.
Included with your new Thermador microwave are the following:
•Care and Use manual (1)
•Quick Guide (1)
•Warranty Card (1)
•Turn Table (1)
•Turn Table Support (1)
B. Trim Kit Models MT27 & MT30
Open the box and carefully remove fillers and all packing materials.
Parts list:
•Trim Frame (1)
•Base Pan (1)
•Trim Bracket (2)
•Duct Side (1)
•Duct, Upper Exhaust (1)
•Duct,Top Intake (1)
•Duct, Rear Intake (1)
•Installation Instructions (1)
•10-foot Roll Tape (1)
•Screws #8x1/4 (20)
•Grommet (1)
TRIM KITS Microwave Oven
Models
30" cabinet MT 30B (Black) MBYB
MT 30W (White) MBYW
MT 30S (Stainless) MBYS
27" cabinet MT27B (Black) MBYB
MT27W (White) MBYW
MT27S (Stainless) MBYS
Caution:
•This trim kit is designed for use only with the Thermador Microwave Oven Models Listed
(See Table 1)
•For Safety, do not alter or modify any part of this kit or oven
Ta b le 1

Page 3
Step 2: Cabinet Preparation
4"
14"
4"
➛
➛
A
➝
➝
➝
➝
➛
➛
➛
➛
BC
➛
➛
Figure 1.
Dimensions Trim Kits
Width (B) 28
-1
/ 2 "±
1
/ 16 MT30B; MT30W; MT30S
25
-1
/ 2 "±
1
/ 16 MT27B; MT27W; MT27S
Height (A) 17"±
1
/ 16 All Trim Kits
Depth (C) 24"±
1
/ 8 All Trim Kits
Outlet should be in
the shaded area.
Microwave
Cutout
Top of
microwave
shelf
1-3/4"
(45 mm)
}
Thermador
single wall
oven cutout
Figure 2.
•The cabinet cut out dimensions are shown in
Figure 1.
•It is good practice, when microwave oven is
installed at the end of a cabinet run, adjacent
to a perpendicular wall or cabinet door, to al-
low at least 1/4" space between the side of
the trim and the wall/door
•Your microwave oven can be installed into a
cabinet or wall by itself or above any of the
following : Thermador wall ovens C271, C301,
CM301, S301, SC301, CJ301 or Thermador
Warming Drawers
WD 27 and WD 30 (See
Figure 2).
•Outlet should be in the shaded area as indi-
cated in Figure 1.
Step 3: Electrical
Installation
The Thermador micro-
wave oven is equipped with
a grounded cord. The wall
receptacle must be in-
stalled and grounded in ac-
cordance with the national
electrical code. Also, elec-
trical connections and
grounding must comply
with all applicable local
codes.
The electrical require-
ments for a separate circuit
serving only this micro-
wave oven are: 120v,60Hz,
15amp.
➛
➛
Warming
Drawer
cutout
Microwave
cutout
1-1/2"
(38 mm)
➝
}
➛
➛

Page 4
Step 4: Installing theTrim Kit
A. Position the 2 vertical trim brackets using the template as shown on Figure 3.
B. Position base pan on cabinet shelf with respect to the center line as shown on Figure
4. The front end of pan should align flush with the front edge of the shelf. Fasten base
pan to shelf with 2 screws #8 x 1/4.
Template is used to locate the positions of the left and
right trim brackets with respect to the cut out. The
trims are secured with (3) screws each and the tem-
plate is discarded after.
Mark the center line of the cut out using the template.
Notch to mark
the center line of
the cutout.
Screws #8 x
1/4
➝
Trim Brackets
.
Centerline
cutout
➝
CENTERLINE MARK
Screws #8 x
1/4
Figure 3.
Figure 4.
➝
Template

Page 5
Step 5: Installing The Microwave Oven (Figure 5)
1. Remove and retain outer case screw at rear
of the oven (left side)
2. Position upper exhaust duct on top (Hinge
Side) of oven. Fasten with outer case screw
3. Position side duct on left side of oven and
fasten it together with upper exhaust duct
by using 2 screws #8x1/4.
Figure 5.
Microwave
Oven
Outer
case
screw
To p
intake
duct
Screw
#8x1/4 Rear
intake
duct
.
Outer case
screw
➝
.
Side
duct
Upper
Exhaust
duct
4. Remove and retain outer case screw at rear
of the oven (right side)
5. Install the grommet and the electrical cord
of the microwave in the receiving hole pro-
vided in the rear intake duct, and position
this duct on rear of the oven (right side).
Fasten with outer case screw.
7. Position top intake duct on upper (right side)
of oven and fasten it together with rear in-
take duct by using 4 screws #8x1/4
8. Apply tape along all ducts flanges. Press tape
to secure properly.
Grommet
Screw
#8x1/4
➝
.
Note: The four (4) ducts have a plastic cover-
ing that must be removed prior to installing
these ducts onto the microwave section.These
ducts have sharp edges. Be careful when han-
dling.

Page 6
9. Remove the left side vertical trim bracket (3
screws) (for MT27 only)
10. Slide the assembled microwave oven in the
prepared cabinet cutout. Plug the electrical
cord in the wall receptacle (ask help from
another person). Align the microwave oven
legs to the pan channel holes (Figure 6).
11. Install back the left side vertical trim bracket.
(3 screws)
12. Snap on the frame trim with the “Therma-
dor Logo under the microwave door button.
(Figure 7)
13. Install the turntable and the turntable sup-
port inside of the microwave oven.
14. Follow the “Care & Use” manuals instruc-
tions for operation
Step 5: Installing The Microwave Oven (continued)
Figure 6.
Figure 7.
Frame Trim

Page 7
Notes

5551 McFadden Avenue, Huntington Beach, CA 92649 • 800/735-4328
ECO 12596 • 16-10-969B • © 2000 BSH Home Appliances Corp. • Litho Date: 8/01
Thermador reserves the right to change specifications or design without notice. Some models are certified for
use in Canada. Thermador is not responsible for products which are transported from the United States for
use in Canada. Check with your local Canadian distributor or dealer. Thermador, 5551 McFadden Avenue,
Huntington Beach, CA 92649.
For the most up to date critical installation dimensions by fax, use your fax handset and call 702/833-3600. Use
code #8030.