Thermaltronics TMT-HA050-2 User manual
USER MANUAL
TMT-HA050-2
HOT AIR TOOL
www.thermaltronics.com
WARRANTY
All equipment and accessories are warranted by Thermaltronics to be free from
defects in materials and workmanship as follows:
Part Number Description Warranty Period
TMT-HA050-2 220-240V Hot Air Tool 1 Year
HA-HE050-2 220-240V Heating Element 30 Days
HA-PU050 Turbine Motor 30 Days
This warranty does not apply to equipment or goods which have been tampered
with, misused, damaged through improper installation or used in a manner
contrary to supplier instructions. Normal “wear and tear” of equipment or goods
is not covered by this warranty. If the product should become defective within the
warranty period, Thermaltronics will repair or replace it free of charge at its sole
option. Warranty period is from the date of purchase by the original owner. If the
date of purchase cannot be substantiated the date of manufacture will be used as
the start of the warranty period.
TABLE OF CONTENTS
TMT-HA050-2 SPECIFICATIONS ................................................................ 1
INTRODUCTION.......................................................................................... 1
SYSTEM FEATURES................................................................................... 1
SAFETY PRECAUTIONS............................................................................. 2
CONTROL PANEL........................................................................................ 2
UNPACKING/ASSEMBLY/OPERATION ...................................................... 3
ORDERING GUIDE...................................................................................... 4
WARNING:
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
This tool must be placed on its stand when not in use.
1
TMT-HA050-2 Hot Air Tool
USER MANUAL
TMT-HA050-2 SPECIFICATIONS
Input Line Voltage: 220-240 VAC
Power: 600 Watts
Temperature Range: 100C - 480C
Pump: Turbine Motor
Air Flow (Max): 35L / min (max)
Fuse: 250V 3A
Size (W x D): 65mm x 265mm
Weight: 1 KG
Certication Marks: CE
INTRODUCTION
Congratulations on your purchase of the TMT-HA050-2 hot air tool. This unit
has been tested and inspected by Thermaltronics prior to shipment, and with
proper maintenance will give you years of reliable performance.
SYSTEM FEATURES
The TMT-HA050-2 hot air tool can be used for surface mount component
removal and reow on components such as SOIC, CHIP, QFP, PLCC and
others.
1. Digital display shows temperature and air ow.
2. Light, portable, plug and use tool.
3. Convection heating allows low pressure hot air to focus on the solder joint.
4. Large selection of high quality nozzles for rework on QFP, SOP, PLCC and
SOJ components.
Functions and Features
2
SAFETY PRECAUTIONS
Warning
A re may result if this equipment is not used with care and for intended applications. To avoid
electric shock or injury, please follow the instructions below strictly:
1. The unit must be properly grounded.
2. The unit can reach extremely high temperatures when switched ON.
- Do not use the device near ammable materials or gases
- Do not touch heated parts, which can cause severe burns
- Do not point the nozzle towards any part of the body
3. Never operate the equipment with wet hands.
4. Always disconnect the power cord and allow the unit ample time to cooldown before performing
maintenance.
5. Use only genuine replacement parts.
6. Do not leave the appliance unattended when it is switched on.
Caution
1. Use this equipment in a well-ventilated area, away from combustible equipment.
2. Disconnect the power cord if the unit is not used for an extended period of time.
3. Place handle in stand when not in use.
4. Handle with care.
- Never drop or sharply jolt the unit.
- The unit contains delicate parts that can be damaged if subjected to physical force.
- Do not spill any liquids into the unit.
5. Do not operate on uneven surfaces.
6. Allow to cool down before storage.
7. Turn off the power when the unit is not in use.
8. Do not alter the unit in any manner.
9. When resting the handle in the handle holder, make sure there are no objects within 30cm of the
nozzle, as nearby objects maybe damaged.
10. Do not apply excessive force when installing and removing nozzles.
11. Do not use pliers to pull the edges of the nozzle.
12. Do not over tighten the screw when installing a new nozzle.
CONTROL PANEL
Reset Button
Decrease Air Flow Button
Temperature and Air Flow Display
Increase Temperature Button Increase Air Flow Button
Decrease Temperature Button
3
TMT-HA050-2 Hot Air Tool
USER MANUAL
UNPACKING/ASSEMBLY/OPERATION
Please read this manual and follow the directions before using the equipment. The carton contains:
1. TMT-HA050-2 Hot Air Tool
2. HTN-D30, HTN-D50, HTN-D80, HTN-D100 nozzles
3. Power Cord
Important: Keep all shipping materials until satisfactory operation has been veried.
Assembly and Operation
1. Remove TMT-HA050-2 Hot Air Tool from its box and place on a suitable work bench.
2. Select the proper nozzle and secure it to the handle.
3. Connect the AC plug to a suitable AC power outlet.
4. Switch the air pump power switch to the “on” position
5. Switch the heater power switch to the "on" position
6. Adjust the air ow and temperature.
7. Wait for the actual temperature to reach the set temperature. The unit should then be ready.
Power Off
1. Increase the air ow to max (99)
2. Decrease the temperature to the lowest setting
3. Wait until the temperature of the heater has cooled down.
4. Switch off the unit, unplug if not used for extended periods of time.
Replacing the Heating Element
Caution: Disconnect power before replacing heater element.
1. Remove the six screws holding the hot air tool together and open the cover.
2. Remove the three screws on the heater PCBA.
3. Disconnect the heater by pressing on the connector lock.
4. Carefully insert a new heating element (HA-HE050-2).
5. Reassemble the hot air gun in the reverse order it was disassembled.
1
3
1
2
4
ORDERING GUIDE
SPARE PARTS & NOZZLES
PART# DESCRIPTION A mm (in) B mm (in)
HTN-PL20 Nozzle 11.9mm x 11.9mm, PLCC-20 11.9 11.9
HTN-PL28 Nozzle 14.5mm x 14.5mm, PLCC-28 14.5 14.5
HTN-PL32 Nozzle 16.9mm x 14.3mm, PLCC-32 16.9 14.3
HTN-PL44 Nozzle 19.5mm x 19.5mm, PLCC-44 19.5 19.5
HTN-PL52 Nozzle 22.0mm x 22.0mm, PLCC-52 22.0 22.0
HTN-PL68 Nozzle 27.0mm x 27.2mm, PLCC-68 27.0 27.2
HTN-PL84 Nozzle 32.4mm x 32.4mm, PLCC-84 32.4 32.4
HTN-QF48 Nozzle 8.4mm x 8.4mm, QFP-48 8.4 8.4
HTN-QF44 Nozzle 13.4mm x 13.4mm, QFP-44 13.4 13.4
HTN-QF80 Nozzle 17.3mm x 17.3mm, QFP-52,80 17.3 17.3
HTN-QF100 Nozzle 23.4mm x 18.1mm, QFP-64,80,100 23.4 18.1
HTN-QF160 Nozzle 31.2mm x 31.2mm, QFP-120,128,144,160 31.2 31.2
HTN-BQ100 Nozzle 22.4mm x 22.4mm, BQFP-100 22.4 22.4
HTN-QF240 Nozzle 34.5mm x 34.5mm, QFP-240 34.5 34.5
HTN-BQ196 Nozzle 37.7mm x 37.7mm, BQFP-196 37.7 37.7
HTN-QF208 Nozzle 29.8mm x 29.8mm, QFP-208 29.8 29.8
HTN-SC16 Nozzle 6.8mm x 10.2mm, SOIC 14, 16 6.8 10.2
HTN-SL16 Nozzle 10.6mm x 10.8mm, SOL 14, 16 10.6 10.8
HTN-SL20 Nozzle 10.6mm x 13.3mm, SOL 20, 20J 10.6 13.3
HTN-SL24 Nozzle 10.6mm x 15.9mm, SOL 24, 24J 10.6 15.9
HTN-SL28 Nozzle 10.6mm x 18.4mm, SOL 28 10.6 18.4
HTN-SL44 Nozzle 16.0mm x 27.9mm, SOL 44 16.0 27.9
HTN-SJ32 Nozzle 13.5mm x 20.6mm, SOJ 32 13.5 20.6
HTN-SJ40 Nozzle 13.5mm x 25.4mm, SOJ 40 13.5 25.4
HTN-TS24 Nozzle 17.0mm x 7.1mm, TSOP 20-24 PIN 17.0 7.1
HTN-TS32 Nozzle 21.0mm x 9.1mm, TSOP 28-32 PIN 21.0 9.1
HTN-TS40 Nozzle 21.0mm x 10.8, TSOP 40 PIN 21.0 10.8
HTN-TS48 Nozzle 21.0mm x 13.3mm, TSOP 48 PIN 21.0 13.3
HTN-TS24B Nozzle 10.2mm x 18.4mm, TSOP 20-24 PIN 10.2 18.4
HTN-TS44 Nozzle 12.7mm x 19.8mm, TSOP 24-28/40-44 PIN 12.7 19.8
SO, TSOP
PLCC, QFP, BQFP
PART# DESCRIPTION
HA-HE050-2 220-240V Heating Element for TMT-HA050-2
HTN-B1010 Nozzle 10.0mm x 10.0mm 10.0 10.0
HTN-B1313 Nozzle 13.0mm x 13.0mm 13.0 13.0
HTN-B1616 Nozzle 16.0mm x 16.0mm 16.0 16.0
HTN-B1919 Nozzle 19.0mm x 19.0mm 19.0 19.0
HTN-B2828 Nozzle 28.0mm x 28.0mm 28.0 28.0
HTN-B3030 Nozzle 30.0mm x 30.0mm 30.0 30.0
HTN-B3232 Nozzle 32.0mm x 32.0mm 32.0 32.0
HTN-B3636 Nozzle 36.0mm x 36.0mm 36.0 36.0
HTN-B3939 Nozzle 39.0mm x 39.0mm 39.0 39.0
HTN-B4141 Nozzle 41.0mm x 41.0mm 41.0 41.0
HTN-B4343 Nozzle 43.0mm x 43.0mm 43.0 43.0
HTN-B4545 Nozzle 45.0mm x 45.0mm 45.0 45.0
BGA
PART# DESCRIPTION A mm (in)
HTN-D30 Nozzle 3.0mm 3.0
HTN-D50 Nozzle 5.0mm 5.0
HTN-D80 Nozzle 8.0mm 8.0
HTN-D100 Nozzle 10.0mm 10.0
Table of contents
Other Thermaltronics Power Tools manuals
