Think ahead SR-2806T User manual

RF RGBW Controller(2 Zones)
Product introduction
SR-2806T with SR-1003RCT series
Parameter
Wiring diagram
Product Size
Easy RGB(W) remote controller is a wireless color controlling system that consists of a sender
and a receiver or several receivers. By selecting switch status, you can set the system as RGB 3-channel
output, or RGBW 4-channel output. Using Easy RGB(W) remote controller, you can get whatever color you
want; you can choose any color from RGB(W) to adjust so as to mix more than 100 mi l l ion kinds of colors.
With built-in 10 kinds of color changing modes, you can easily switch color changing modes and adjust speed
and brightness. “Function Pause” enables RGBW LED to stay at your favorite color under the situation of color
changing modes, which operation is simple but functional.
Part No. Iuput Voltage Remarks
Current
SR-1003RCT 12-36VDC Constant voltage
4x(60-180)W
4x5A
Output
SR-1003RCTEA 12-36VDC Constant voltage
4x(96-288)W4x8A
Remote
Part No. Operation Voltage DIMENSIONS
ø/h (mm)
Operation
Frequency
SR-2806T 4.5VDC 43.8x131.6x24.5
434MHz/868MHz
Receiver
SR-1012RCT 12-36VDC Constant current
4x(4.2-12.6)W
4x350mA
SR-1022RCT 12-36VDC Constant current
4x(8.4-25.2)W4x700mA
43.8
131.6
24.5
Brief introduction of buttons
R“R”button and indicator G“G”button and indicator
B“B”button and indicator W“W”button and indicator
Working status indicator, the sender is in dormant status when the indicator is off. The
sender is under working when the indicator is flashing rapidly. If the indicator continues
flashing at the frequency of 1 second, it indicates that the sender batteries low and
needs to replace new batteries.
S- Speed down when color is changing S+ Speed up when color is changing
M
B- Brightness down B+ Brightness up
Turn ON/OFF
Touch wheel for selecting R/G/B colors
R G B W
S- S+
W+
B- B+
Z1 Z2
P1 P2 P3 P4
12 3 4
Z1 Z2
P1 P2 P3 P4
1 2 34
Each program shall be speed selectable from 20 seconds (most fast) to 15 minutes
(slowest). When you press the button first, the program starts, after a second press, it
pauses, then after pressing again, the program continues.
The programs shall include the following:
- smooth color change (red, yellow, green, turquoise, blue, pink, white)
- smooth change of warm color range (red, yellow, pink, hot pink and mixed warm
colors)
- smooth change of cold color range ( blue, green, turquoise, light blue, white,mixed
cold colors)
- hard color change (red, orange, yellow, green, light blue, dark blue, pink)
2 zones
4 programs.
4 buttons for storable colors. The user can chose his 4 favorite colors by using the
color-wheel or the color change programs and can save each one by pressing the
particular button for 3 seconds.
With this button it shall be getting three shades of white color (cold white, neutral white
and warm white; a mixture of RGB colors), and to get white color while using the
controller in RGB-mode.
This function needs to be available in RGBW-mode as well to get a versatile white color
range.
Power Supply
12-36VDC
LN
110V-230VAC
RGB/RGBW
white
SR-1003RCT
RGB/RGBW
white
SR-1003RCT
RGB/RGBW
white
SR-1003RCT
Think ahead ESC GmbH I Anzengruberstr. 39 I A-9020 Klagenfurt a. W. I T [phone] I [email protected] I www.think-ahead.at

Safety & Warnings
Warranty Agreement
1) The product shall be installed and serviced by a qualified person.
2) IP20.Please avoid the sun and rain. When installed outdoors, please ensure it is mounted in a water proof
enclosure.
3) Always be sure to mount this unit in an area with proper ventilation to avoid overheating.
4) Please check if the output voltage of any LED power supplies used comply with the working voltage of the
product.
5) Never connect any cables while power is on and always assure correct connections to avoid short circuits
before switching on.
6)
7) For update information please consult your supplier.
Please ensure that the cable is secured tightly in the connector
1) We provide lifelong technical assistance with this product:
3-year warranty. We print date on every products, for example :1125 means year 2011,week 25.The
warranty is for free repair or replacement and covers manufacturing faults only.
For faults beyond the 3-year warranty we reserve the right to charge for time and parts.
2) Limited Warrenty
Any defects caused by wrong operation.
Any damages caused by unauthorized removal, maintenance, modifying, incorrect connection and
replacement of chips.
Any damages due to transportation, vibration etc. after purchase.
Any damages caused by earthquake, fire, lightning, pollution and abnormal voltage.
Any damages caused by negligence, inappropriate storing at high temperatures and humidity or near
harmful chemicals.
Product has been updated
3) Repair or replacement as provided under this warranty is the exclusive remedy to the customer.
1. Do wiring according to connection diagram and install battery into remote control.
2. How to learn&delete ID process?
a. Wake up the remote by any button except touch color wheel.
b. Press at learning button on receiver.
c. Press any zone button(which you desire to control) on remote.
d.Then touch color wheel.
e.Connected LED light will blink to confirm zone designation.
f.Press learning button on receiver for over 5 seconds until connected LED light flash off,
then delete the learned ID. If you want to learn receiver into another zone, please follow
learning ID process operation 2.
Operation
Think ahead ESC GmbH I Anzengruberstr. 39 I A-9020 Klagenfurt a. W. I T [phone] I [email protected] I www.think-ahead.at