Thinkware Z3000Plus User manual

2Channel Dash Cam
This product records videos while the vehicle is operating.
Read and follow the instructions in this guide to properly use and maintain the product.
User Guide

Before using the product
About the product
This product records videos while the vehicle is operating. Use this product only for reference when
investigating incidents or road accidents. This product is not guaranteed to record or process cloud data
for all events. The device may not record accidents with impacts that are too minor to activate the impact
sensor or accidents with massive impacts that cause the vehicle’s battery voltage to deviate.
Video recording does not begin until the product is completely turned on (booted up). To ensure that all
vehicle events are recorded, wait until the product is completely booted up after turning it on, and then
begin operating the vehicle.
THINKWARE is not responsible for any loss caused by an accident, nor is it responsible for providing any
support regarding the outcome of an accident.
Depending on the vehicle's configuration or operating conditions, such as the installation of remote door
lock devices, ECU settings, or TPMS settings, some product features may not be supported, and different
firmware versions may influence the product's performance or features.
About the user guide
The information provided in the guide may change when the manufacturer updates its service policy. This
user guide is intended for THINKWARE Z3000Plus models only, and it may contain technical errors,
editorial errors, or missing information.
Copyrights
All rights for the content and maps in this guide are reserved by THINKWARE and are protected under
copyright laws. All unauthorized duplication, revision, publication, or distribution of this guide without
written consent from THINKWARE is prohibited and is eligible for criminal charges.
Registered trademarks
THINKWARE Z3000Plus is a registered trademark of THINKWARE.
Other product logos and service names in this guide are trademarks of the relevant companies.

FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC CAUTION: Any changes or modifications to the equipment not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
Information to user : RSS-247
This device complies with Industry Canada’s licence-exempt RSSs.
Please be cautioned the changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Notice: Operation is subject to the following two conditions : (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.

4
Contents
Safety information 6
1. Product overview 7
1.1 Included items 7
1.1.1 Standard items
1.1.2 Accessories (sold separately) 7
1.2 Part names
1.2.1 Front camera(main unit) - front view 8
1.2.2 Front camera(main unit) - rear view 9
1.2.3 Rear camera 9
1.3 Removing and inserting the memory card 10
2. Installing the product 11
2.1 Installing the front camera (main unit) 11
2.1.1 Selecting an installation location 11
2.1.2 Securing the product 11
2.1.3 Connecting the power cable 13
2.2 Installing the rear camera 14
2.2.1 Selecting an installation location 14
2.2.2 Securing the rear camera 14
2.2.3 Connecting the rear camera cable 15
3. Using recording features 19
3.1 Turning the product on or off 19
3.2 Turning the LCD on or off 20
3.3 Learning about the file storage location 20
3.4 Using the continuous recording feature 21
3.5 Recording manually 21
3.6 Using parking mode 22
3.7 Using the Super Night Vision 23
3.8 About the screen layout 24
3.8.1 Live view screen 24
3.8.2 Home screen 25
3.9 Playing the videos 26
3.9.1 Playing on the product 14
2.2.3 Connecting the rear camera cable 15
5. Settings 33
5.1 Setting the camera 33
Setting the brightness of the camera
(brightness camera)
5.2 Setting recording features 33
- Cont. Sensitivity
- Night Vision
- Parking Mode
- Parking Sensitivity
- Motion Sensitivity
- Off Timer
- Battery Protection
- Off Voltage
- Wt Bty Protection
5.3 System Settings 35
- Language
- Volume
- Calibrate Touchscreen
- LCD Brightness
- LCD Auto-Off
- Security LED
- Set Date and Time
- Partition Settings
- Format Memory
- Restore Settings
6. Accessing the product information 46
6.1 Understanding the product features 46
6.2 Viewing the product information 46
7. Upgrading the firmware 47
8. Using the PC viewer 48
8.1 System requirements 48
8.2 PC viewer for Windows 48
8.3 PC viewer for Mac 52
9. Troubleshooting 56
10. Specifications 57

6
Safety information
Read the following safety information to properly use the product.
Safety symbols in this guide
"Warning" - Indicates a potential hazard which, if not avoided, may result in injury or death.
"Caution" - Indicates a potential hazard which, if not avoided, may result in minor injury or property damage.
"Note" - Provides useful information to help users better utilize the product's features.
Safety information for proper use
•Do not operate the product while driving a vehicle. Distraction while driving may cause accidents and
result in injury or death.
•Install the product in places where the driver's view is not obstructed. Obstruction of the driver’s vision
may cause accidents and result in injury or death.
•Do not use damaged power cables. Doing so may result in electrical fire or electrocution.
•Disconnect the power cable from the product when it will not be used for an extended period. Failure to do
so may result in electrical fire or battery depletion.
•Ensure that the product is out of the reach of children and pets. If the product breaks, it may result in fatal
damage.
•Do not expose product to direct sunlight or intense light. The lens or internal circuitry may fail otherwise.
•Avoid excessive humidity and do not allow any water to enter the product. Electronic components inside
the product may fail if exposed to humidity or water.
•Do not disassemble the product or subject the product to impact. Doing so may damage the product.
Unauthorized disassembly of the product voids the product warranty.
•Do not apply excessive force when pressing the buttons. Doing so may damage the buttons.
•Ensure you are inserting the memory card correctly before inserting it to the product. The memory card
slot or the memory card may be damaged if it is inserted incorrectly.
•When connecting the power cable to the product, ensure that the connection between the cable plug
and the power cable connector on the product is secure. If the connection is loose, the power cable may
become disconnected due to vehicle vibration. Video recording is not available if the power connector is
disconnected.

7
1. Product overview
1.1 Included items
Ensure that all the items are included when you open the product box.
1.1.1 Standard items
1.1.2 Optional items
Front camera (main unit) Mount
12V Power Cable
OBD-II Cable
Adhesive cable holder
MicroSD memory card with adapter
(MicroSD Card is inserted in the front camera)
Warranty
GND
ACC
BATTERY
Hardwiring cable Rear Camera cable
Rear camera

Product overview
8
1.2 Part names
1.2.1 Front camera (main unit) - front view
DC-IN power
connector
Used to connect the
power cable.
V-IN input port
Used to connect the
rear camera.
Mount connector
Used to connect the mount
Speaker
Outputs the voice guide and buzzer
sounds to indicate the product’s status. Security LED
Indicates that the video is being recorded.
Front camera lens
Records the front view.
Power switch
Used to turn
on or off the product.
Memory card slot
Insert a memory card
to save recordings.

Product overview
9
1.2.2 Front camera (main unit) - rear view
Reset button
Insert the tip of a sharp object to reset
the product when an error occurs.
Microphone
Used for voice recording.
Status LED
Indicates the operating
status of the product.
Touchscreen
Used for setting the product or
viewing the recorded videos.
Gently touch the screen to make inputs on the touchscreen. The screen may be damaged if you apply
excessive force to the screen or if you touch the screen with a sharp object.
1.2.3 Rear camera
Adhesive mount
Used to fix the rear camera in the vehicle.
Rear camera lens
Records the rear view.
Security LED
Indicates that the video is
being recorded.
Connection port
Used to connect the rear camera cable.

Product overview
10
1.3 Removing and inserting the memory card
The memory cards are installed in the product at the factory. Follow the instructions to remove the memory
card from the product or to insert the memory card into the product.
Removing the memory card
Ensure that the product is turned off, and then gently
push the bottom of the memory card with your
fingernail. The lower part of the memory card will be
exposed.
Remove it from the product.
Inserting the memory card
Insert the memory card into the memory card slot,
paying attention to the direction of the memory card,
and then push the memory card into the slot until
you hear a click.
Before inserting the memory card, ensure that the
metal contacts on the memory card are facing
toward the lens of the product.
•Ensure that the product is turned off before removing the memory card. The recorded video files may be
corrupted or lost if you remove the memory card while the product is on.
•Ensure that the memory card is in the correct direction before inserting it into the product. The memory
card slot or the memory card may be damaged if it is inserted incorrectly.
•Use only authentic memory cards from THINKWARE. THINKWARE does not guarantee compatibility and
normal operation of third-party memory cards.
To prevent loss of recorded video files, periodically back up the video files on a separate storage device.

11
2. Installing the product
2.1 Installing the front camera (main unit)
Follow the instructions to properly install the product.
2.1.1 Selecting an installation location
Select an installation location that can record the
entire view in front of the vehicle without obstructive
the driver’s vision. Ensure that the front camera lens
is located in the center of the windshield.
If a GPS navigating device installed on the dashboard is
present, its GPS reception may be affected depending
on the dashboard camera's installation location.
Adjust the installation location of the GPS navigating
device to ensure that the two devices are separated by
at least 8 inches.
2.1.2 Securing the product
Follow the instructions to secure the product at the installation location.
1
2
Align the mount to the mount connector on the
product, and then slide it until you hear a click (
➊ ).
Then, carefully remove the protective film keeping
the lens clean (
➋ ).
2
1
20 cm