thomann box pro DSP 18 Sub User manual

DSP 18 Sub
active speaker
user manual

Musikhaus Thomann
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: [phone]
E-mail: [email protected]
Internet: www.thomann.de
18.06.2019, ID: 424348 (V2)

Table of contents
1 General information................................................................................................................................. 4
1.1 Further information........................................................................................................................... 5
1.2 Notational conventions.................................................................................................................... 6
1.3 Symbols and signal words............................................................................................................... 6
2 Safety instructions..................................................................................................................................... 8
3 Features....................................................................................................................................................... 13
4 Installation.................................................................................................................................................. 14
4.1 Tips on handling speakers............................................................................................................ 15
5 Connections and controls................................................................................................................... 16
6 Technical specications....................................................................................................................... 19
7 Plug and connection assignment.................................................................................................... 22
8 Protecting the environment.............................................................................................................. 25
Table of contents
DSP 18 Sub
3

1 General information
This user manual contains important information on the safe operation of the device. Read and
follow all safety notes and all instructions. Save this manual for future reference. Make sure
that it is available to all persons using this device. If you sell the device to another user, be sure
that they also receive this manual.
Our products and user manuals are subject to a process of continuous development. We there‐
fore reserve the right to make changes without notice. Please refer to the latest version of the
user manual which is ready for download under www.thomann.de.
General information
active speaker
4

1.1 Further information
On our website (www.thomann.de) you will nd lots of further information and details on the
following points:
Download This manual is also available as PDF le for you to download.
Keyword search Use the search function in the electronic version to nd the topics of
interest for you quickly.
Online guides Our online guides provide detailed information on technical basics
and terms.
Personal consultation For personal consultation please contact our technical hotline.
Service If you have any problems with the device the customer service will
gladly assist you.
General information
DSP 18 Sub
5

1.2 Notational conventions
This manual uses the following notational conventions:
The letterings for connectors and controls are marked by square brackets and italics.
Examples: [VOLUME] control, [Mono] button.
1.3 Symbols and signal words
In this section you will nd an overview of the meaning of symbols and signal words that are
used in this manual.
Letterings
General information
active speaker
6

Signal word Meaning
DANGER! This combination of symbol and signal word indicates an
immediate dangerous situation that will result in death or
serious injury if it is not avoided.
CAUTION! This combination of symbol and signal word indicates a pos‐
sible dangerous situation that can result in minor injury if it
is not avoided.
NOTICE! This combination of symbol and signal word indicates a pos‐
sible dangerous situation that can result in material and
environmental damage if it is not avoided.
Warning signs Type of danger
Warning – high-voltage.
Warning – danger zone.
General information
DSP 18 Sub
7

2 Safety instructions
This device is designed for sound reinforcement. Use the device only as described in this user
manual. Any other use or use under other operating conditions is considered to be improper
and may result in personal injury or property damage. No liability will be assumed for damages
resulting from improper use.
This device may be used only by persons with sucient physical, sensorial, and intellectual
abilities and having corresponding knowledge and experience. Other persons may use this
device only if they are supervised or instructed by a person who is responsible for their safety.
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not
within reach of babies and young children. Choking hazard!
Ensure that children do not detach any small parts (e.g. knobs or the like) from
the unit. They could swallow the pieces and choke!
Never let children unattended use electrical devices.
Intended use
Safety
Safety instructions
active speaker
8

DANGER!
Electric shock caused by high voltages inside
Within the device there are areas where high voltages may be present. Never
remove any covers.
There are no user-serviceable parts inside.
Do not use the device if covers, protectors or optical components are missing or
damaged.
DANGER!
Electric shock caused by short-circuit
Always use proper ready-made insulated mains cabling (power cord). Do not
modify the mains cable. Failure to do so could result in electric shock/death or
re. If in doubt, seek advice from a registered electrician.
Safety instructions
DSP 18 Sub
9

CAUTION!
Possible hearing damage
The device can produce volume levels that may cause temporary or permanent
hearing impairment. Over an extended period of time, even levels that seem to
be uncritical can cause hearing damage.
Decrease the volume level immediately if you experience ringing in your ears or
hearing impairment. If this is not possible, keep a greater distance or use su‐
cient ear protectors.
NOTICE!
Risk of re
Do not block areas of ventilation. Do not install the device near any direct heat
source. Keep the device away from naked ames.
Safety instructions
active speaker
10

NOTICE!
Operating conditions
This device has been designed for indoor use only. To prevent damage, never
expose the device to any liquid or moisture. Avoid direct sunlight, heavy dirt, and
strong vibrations.
NOTICE!
Power supply
Before connecting the device, ensure that the input voltage (AC outlet) matches
the voltage rating of the device and that the AC outlet is protected by a residual
current circuit breaker. Failure to do so could result in damage to the device and
possibly injure the user.
Unplug the device before electrical storms occur and when it is unused for long
periods of time to reduce the risk of electric shock or re.
Safety instructions
DSP 18 Sub
11

NOTICE!
Possible damage due to installation of a wrong fuse
The use of dierent types of fuses can cause serious damage to the unit. Fire
hazard!
Only fuses of the same type may be used.
Safety instructions
active speaker
12

3 Features
The device is characterized by the following features:
n18" woofer
nClass D amplier
nBuilt-in sound processor
nConnection options: XLR connections for signal in and outputs (L+R, and crossover)
nPhase switch
nSwitchable Low-Pass lter 90/120 Hz
nPole mount (M20)
nTwo carrying handles
nCasing made of medium-density breboard (MDF)
nPowder-coated front grille
Features
DSP 18 Sub
13

4 Installation
Unpack and check carefully there is no transportation damage before using the unit. Keep the
equipment packaging. To fully protect the product against vibration, dust and moisture during
transportation or storage use the original packaging or your own packaging material suitable
for transport or storage, respectively.
Create all connections while the device is o. Use the shortest possible high-quality cables for
all connections. Take care when running the cables to prevent tripping hazards.
CAUTION!
Risk of injury due to heavy weight
Due to the heavy weight of the device, at least two persons are required for trans‐
port and installation.
Installation
active speaker
14

NOTICE!
Possible property damage by magnetic elds
Loudspeakers produce a static magnetic eld. Therefore, maintain an appropriate
distance to devices that can be adversely aected or damaged by an external
magnetic eld.
4.1 Tips on handling speakers
We recommend you to set up the speakers in a way, that the sound signals can reach the audi‐
ence unobstructedly. It will often be helpful to mount the speakers on tripods. Thus, the sound
will be evenly spread with maximum range throughout the audience area.
Always use high grade cable to connect your equipment. Otherwise you won't reach max‐
imum sound quality.
If you notice distortion during operation, the active speaker is overloaded. This may perma‐
nently damage the device. Always reduce the volume as soon as you hear distortion.
Installation
DSP 18 Sub
15

5 Connections and controls
Connections and controls
active speaker
16

1[Balanced Outputs]
Balanced line signal outputs, designed as XLR chassis plug.
2[Balanced Inputs]
Balanced line signal inputs, designed as XLR chassis socket.
3[Phase]
If necessary, this switch shifts the phase of the subwoofer signal by 180 °. This avoids unwanted cancellation eects in
combination with other speakers.
4[Subwoofer Level]
Volume control.
5[Xover]
Crossover frequency switch Toggles between 90 Hz and 120 Hz.
6[Outputs Mode]
This switch is used when using active speaker boxes. In [Link] position, all signals from 20 Hz to 20 kHz are output to
the speaker boxes. If the switch is in [Xover] position, only signals above 90 Hz/120 Hz are output to the speaker
boxes.
Connections and controls
DSP 18 Sub
17

7[Signal]
LED (green): Indicates that the input signal is present.
8[Limit]
LED (red): Indicates overload. In this case, the level of the line input signal is too high.
9[Power]
LED (blue): Indicates that operating voltage is present.
10 [POWER]
Mains switch. Turns the device on and o.
11 IEC chassis plug with fuse for the power supply.
Connections and controls
active speaker
18

6 Technical specications
Speaker 1 × 18" woofer
Input connections Voltage supply IEC chassis plug C14
Line signal 2 × XLR chassis socket
Input impedance 22 kΩ
Output connections Line signal 2 × XLR chassis plug
Output power RMS: 800 W
Peak: 1800 W
Frequency range 30 Hz … 150 Hz
Crossover frequency 80 Hz or 120 Hz
Signal-to-noise ratio 70 dB
Sound pressure level (SPL), max. 128 dB
Power consumption 980 W
Technical specications
DSP 18 Sub
19

Supply voltage 230 V 50 Hz
Fuse 5 mm × 20 mm, 5 A, 250 V, slow-blow
Dimensions (W × H × D) 610 mm × 680 mm × 745 mm
Weight 39 kg
Ambient conditions Temperature range 0 °C…40 °C
Relative humidity 50 %, non-condensing
Design Bass reex
Truss-capable No
Stand mounting Yes
Casters No
Further information
Technical specications
active speaker
20