ENGLISH
PRODUCT DESCRIPTION AND RECOMMENDATION
This arm blood pressure monitor is an electronic device intended to make
human blood pressure and pulse rate at arm of adult population.
In order to get reliable measurements, keep taking and recording blood
pressure measurement at the same time every day and avoid eating,
bathing, smoking, exercising, ingest caffeine or alcohol at least 30 minutes
prior to take measurement.
Be seated and relax for at least 5 minutes before measuring
Make sure the cuff is at heart level for taking measurement
To make repeated measurements, the rest interval between measurements
shall not be less than 3 minutes.
Consult your physicians for interpretation of blood pressure measurement
and follow their direction.
This blood pressure monitor could be used with Thomson healthcare app
downloadable on Apple Store and Play Store. The app is also suitable with
Apple Health Kit.
TIPS FOR MEASUREMENT
It can cause inaccuracy if the measurement is taken in the following
circumstances:
Within 1 hour after dinner or drinking
Immediate measurement after tea, coffee, smoking
Within 20 minutes after taking a bath
When talking or moving your fingers
In a very cold environment
When you want to discharge urine
SECURITY
This arm blood pressure monitor can be only used for which it has been
designed as explained in the instruction booklet
Consult your physician for health status and blood pressure range before
taking measurement at home with this device
Do not press the power button if the cuff has not been properly wrapped
If the cuff causes you any discomfort during measurement, press the power
button to turn off the device immediately
Pull off the Velcro strap to detach the cuff if the cuff pressure exceeds
300mmHg without an automatic exhaust
Do not modify or try to repair this device by yourself
MAINTENANCE
Clean your device with a soft dry cloth, lens with a cotton swab
moistened with water then wipe it dry
Do not store the device with direct sunlight and keep it away water
Remove batteries from your device if you don’t use for a long time
OVERVIEW
INITIAL START-UP
Use the AC power adaptor by connecting to the blood pressure monitor to
reload the Li-polymer battery.
Before using the device, please make sure that the ON/OFF BUTTON is
ON.
Setting Date, Time and Measurement Unit
Press the USER 1 BUTTON during 3 seconds until the hour on the left of
the screen display starts to flash.
Press the left button “query” to set the hour. Each press is increasing the
number of hour.
To confirm the hour, press the USER 1 BUTTON then the numeral
representing minute starts to blink.
Repeat the previous steps to set the time.
Repeat the previous steps to set the month, day, year.
Repeat the previous steps to set the measurement unit.
After confirming measurement unit, the LCD will display „dONE” and the
monitor will shut off automatically
It’s ready to take measurements.
PAIR-UP THE BPM WITH YOUR DEVICE
Turn on Bluetooth and the Thomson Healthcare app. Please make sure that
both are working.
Launch the app to start the pair-up. For more informations about using the
Thomson Healthcare app, please visit our website: www.thomson-hc.eu
When the monitor is OFF, press and hold the START button for about 2 sec
to start the pair-up. The symbols and appear on the
display which means the pair-up is in progress.
Then, one of the two following symbols will appear :
If succeed
If fail
TO TAKE A MEASUREMENT
1- Remove all accessories (watch, bracelet, etc) from your left arm. If your
physician has diagnosed you with poor circulation in your left arm, use your
right arm
2- Roll or push up your sleeve to expose the skin
3- Apply the cuff to your left arm with your palm facing up
4- Position the edge of the cuff about 2-3 cm of the elbow with your palm up.
5- Fasten the arm cuff around your arm, leaving no extra room between the
cuff and your skin. If the cuff is too loose, the measurement will not be
accurate
6- Resting for 5 minutes before measuring
7- Wait at least 3 minutes between measurements
8- For a meaningful comparison, try to measure under similar conditions. For
example, take daily measurement at approximately the same time, on the
same arm, or as directed by a physician
START THE MEASUREMENT
Press your selected user button to turn on the monitor, it will complete the
measurement process automatically.This device will proceed to data
transmission automatically after measurement. The wireless symbol appears
to transmit the data.
RECALLING THE RECORDS
Press „QUERY” button to access to memory of the selected user when the
BPM is off
Press “QUERY” again to visualize one by one all the measurements. The
blood pressure monitor can store 60 measurements by user.
DELETING THE RECORDS
To delete a record, press the QUERY BUTTON about 3 seconds when it’s in
the memory mode. When the message “dEL ALL” display on the screen,
press QUERY BUTTON again.
TROUBLE SHOOTING
The display is dim or is not lighting up
Check out if the battery is exhausted, if it's exhausted, please charge the
power in time.
E1 : Data communication has failed
Make sure that phone’s Bluetooth is on or within the distance range
E3 : Inflation is slow or the cuff is not secure
Refasten the cuff and then measure again
E10 / E11 : The monitor detected motion while measuring
