Microlife WatchBP Office Targe User manual

EN 1
Ofce blood pressure
measurement device
with built-in
Blood Pressure targets.
Instruction Manual

WatchBP Ofce Target is designed with built-in blood pressure targets to provide
convenient, accurate and reliable ofce blood pressure measurements. It follows the
recommended guidelines of the European Society of Hypertension (ESH)1, American Heart
Association (AHA)2, American Diabetes Association (ADA)3 and World Health Organization
(WHO)4.
1
O’Brien E, Asmar R, Beilin L, Imai Y, et al. European Society of Hypertension recommendations for conventional, ambulatory and home blood pressure
measurement. European Society of Hypertension Working Group on Blood Pressure Monitoring. J Hypertens 2005;23:697-701.
2
Pickering TG, Hall JE, Appel LJ, et al. Recommendations for Blood Pressure Measurement in Humans and Experimental Animals:
Part 1: Blood Pressure Measurement in Humans: A Statement for Professionals From the Subcommittee of Professional and Public Education of the American
Heart Association Council on High Blood Pressure Research. Hypertension 2005;45;142-161.
3
American Diabetes Association. Standards of Medical Care in Diabetes–2006. Diabetes Care, 2006;29; Supplement 1.
4
World Health Organization, International Society of Hypertension Writing Group. 2003 World Health Organization (WHO) / International Society of
Hypertension (ISH) Statement on Management of Hypertension. J Hypertens 2003,21:1983-1992.

EN
Product description
Name of parts and display ................................. 3–4
Components and accessories...... ........................... 5
Before using WatchBP Ofce Target
Activating the device ............................................. 6
Selecting and tting the correct cuff .................. 6–8
Selection of operation modes
«Single» or «Triple» Mode («Double» Mode as
option) ................................................................. 10
Press «140/90» or «130/80» ..............................10
Trafc light indications
Green light ........................................................... 11
Red light ............................................................... 11
Viewing and deleting of measurements
Viewing the stored values ...................................12
Pulse pressure (PP) .............................................. 12
Deleting the stored values ................................... 13
Replacing slot-in instruction card ......................... 13
Appendix
Battery and power adaptor ........................... 14–15
Error messages ............................................... 16–18
Safety, care, accuracy test and disposal ......... 19–20
Technical specications ....................................... 21
Table of Contents

3
SYS.
mmHg
DIA.
mmHg
PUL.
/min
1
3
3
SYS.
DIA.
PUL.
mmHg
mmHg
/min
Main Adaptor
Cuff Socket
Mode Switch
Display
Instruction
M Button (Memory)
Start/Stop Button
Product description
Name of parts
Battery Compartment

4EN
Target 1 < 140/90
Difference to Target setting
Heart Beat
Interval Time
Battery Symbol
Memory
Triple Mode
Target 2 < 130/80
Systolic Value
Diastolic Value
Pulse Pressure (PP)
Pulse Rate
3
Display

5
WatchBP Ofce Target and components
WatchBP Ofce Target
Blood Pressure Device X 1
AC Adaptor X 1
Input: 100-240V~50/60Hz 0.7A
Output: +6V 0.6A
M size (22cm~32cm) X 1
L size (32cm~42cm) X 1
Instruction Manual X 1
Quick Start Guide X 1
3
SYS.
DIA.
PUL.
mmHg
mmHg
/min

EN
6
Before using WatchBP Ofce Target
Two ways of activating the Device
1) Pull out the protective strip projecting from the
battery compartment.
2) Plug the adapter cable into the main adapter
socket in the blood pressure monitor; then Plug
the adapter plug into the wall socket.
M (Medium size)
22 - 32 cm (8.7 - 12.6 inches)
L (Large size)
32-42 cm (12.6 - 16.5 inches)
Selecting the correct cuff
Two different cuff sizes are provided with the
WatchBP Ofce Target: Medium and Large. Use the
cuff marker to select the cuff size that best matches
the circumference of the patient’s upper arm.

7
Before using WatchBP Ofce Target (cont.)
Fitting the cuff properly
1) Place the cuff over the left (right) upper arm so
that the air tube and artery mark arrow point
towards the lower arm.
2) Lay the cuff on the arm. Make sure that the lower
edge of the cuff lies approximately 2 to 3cm ( ¾
to 1 inch) above the elbow.
Connect the cuff to the device
Connect the cuff to the device by inserting the cuff
connector into the cuff connector socket.
2-3 cm
(3/4 to 1 inch)

EN
8
3) Wrap and tighten the cuff around the arm.
4) Leave a little free space between the arm of the
patient and the cuff. It must be possible to t 2
ngers between the arm and the cuff. Clothing
must not restrict the arm. Remove all clothing
covering or constricting the arm to be measured.
5) It may result in incorrect blood pressure readings
if the cuff does not t properly. Use a different
size cuff if the range index at the end of the cuff
does not fall into the range specied by the
range stripes.
6) Apply the same steps to the other arm if a
measurement of the other arm is required.
* When the cuff is wrapped
around the arm, the edge of
the cuff should be in the range
which is marked “OK”.

9
SYS.
mmHg
DIA.
mmHg
PUL.
/min
1
3
SYS.
mmHg
DIA.
mmHg
PUL.
/min
1
3
Automated triple measurements
In «3» Mode, the WatchBP Ofce Target
device automatically takes three consecutive
measurements at default 15 second intervals.
Because blood pressure constantly uctuates, a
result determined in this way is more reliable than
one produced by a single measurement.
15 sec.
1 2
Selecting the operation mode: Standard or Triple mode
Select an operation mode
There are two measuring modes to be selected,
Standard mode (standard single measurement) or
Triple mode (automatic triple measurements).
To select Standard mode, slide the switch on the
right side of the device downwards to position «1».
To select Triple mode , slide this switch upwards to
position «3».
15 sec.
3
*15 seconds of interval is adequate according to «Blood
Pressure Monitoring, 2001, 6:145-147» for oscillometric
instruments).