Thuli Tables Tour Abdominal Swing-Away Installation and operating instructions

This addendum to the Tour Owner’s Manual will familiarize you with the features and operation of the
Abdominal Swing-Away and Interchangeable Chest Cushions.
THULI TABLES, INC.
800.458.4854 608.935.9300 fax [phone] of[email protected] www.thuli.com
OWNER'S MANUAL ADDENDUM Tour Abdominal Swing-Away

GAS SPRING INSTALLATION (cont)
Insert the base end mount of the black gas spring in to the slot in
the aluminum mount block which is attached to the cross brace
of the front legs. Do this by pulling outward on the white handled
spring pin, inserting the gas spring base end tab and then releasing
the white handled spring pin until it engages in the tab.
GAS SPRING INSTALLATION (cont)
Repeat previous step on the operating end of black gas spring
where it attaches to the abdominal cushion. You may need to
pull up or push down slightly on the abdominal cushion by
grasping the aluminum mount block to help with alignment so
that the engaging spring pin slides in easily.
GAS SPRING INSTALLATION
GAS SPRING & CONTROL LEVER REMOVAL
Remove the abdominal swing-away gas spring and control lever
from its storage location. Note that the control lever is positioned
and attached by a magnetic latch.
Slide the black control lever housing onto the front folding leg
support brace and position it to come into contact with the black
poly lock. It will be held in place with an internal magnet.
The abdominal swing-away section is now installed. Tip the table upright.
Abdominal Swing-Away Section: Set-Up (follows pg 9)

ABDOMINAL SWING-AWAY: POSITIONING
Activate the lever on the side of the table while depressing the
abdominal section. This may be done before the patient lays on
the table or while the patient is on the table. Adjust the positon
of the abdominal swing-away to the patient’s comfort.
Please note: When mounting this table to a
Conversion Base, the gas spring must be removed and
set aside until used as a portable table.
This abdominal swing-away section offers prone comfort to
pregnant patients or to those of us with “a little extra around
the middle.”
Abdominal Swing-Away Section: Operation

The chest cushions are attached by way of four magnets. To
remove the cushion, simply grasp at both sides and twist toward
the headpiece with a lifting motion. The cushion is held in
correct position by alignment of two holes on the underside of
the chest cushion with the two nickel plated acorn nuts on the
thoraic drop plate.
CHEST CUSHION: STORAGE
When not using the chest cushion, consider:
1. Setting it aside.
2. Storing it in the space vacated by the extended ankle rest
section (photo above).
3. Use it as a bolster under the patient’s ankles when lying prone.
4. Use it as a bolster under the patient’s knees when lying supine.
This cushion provides a combination of soft foam in the breast
area and rmer foam surrounding, insuring adequate thoracic
support when the patient is lying prone. The rmer sternal
cushion allows for performing “anterior thoracic” adjustments.
CHEST CUSHION: PLACEMENT
Following Step 2 under the heading “When folding the table...”
on page 15 of the Tour Owner’s Manual, detatch and store the
gas spring and control lever in the reverse sequence that you
used in set up.
Note that the “operating end” of the gas spring must be positioned
with the cable attachment/lever apparatus pointing upward (see
photo 1 in this Addendum). The black cylinder of the gas spring
should be snapped into the spring clamps and positioned to re-
move all slack from the gray cable sheath. Attention to this
positioning will allow the two cushions of the headpiece to
straddle the apparatus when it is stored.
Interchangeable Chest Cushions
STANDARD CHEST CUSHION:
This cushion has a foam density that matches the rmness of
the rest of the table. This is likely the cushion you will use for
most patients.
“FEMALE FRIENDLY” CHEST CUSHION:
Table Fold Down