tigerlight MAKO Series User manual

MAKO Series LED Area Light
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION
IMPORTANT INSTALLATION INFORMATION
1.Before commencing installation or maintenance, ensure
electricity is switched off at the mains. Installation or
maintenance should be carried out by a qualified electrician.
2.The luminaire must not, under any circumstances, be installed
directly to flammable materials, and luminaires must not be
covered with any flammable materials.
3.Mounting height range of 3 meters to 6 meters, this model is
suitable for outdoor lighting.
4.Ensure there is adequate free air circulation of at least 50cm
around the luminaire. All luminaires run hot. It is the installer's
responsibility to consider fire risk and take appropriate
precautions.
3
1 2
4
Installation Instruction & Installation Steps
STEP 2:
1.When the pole is inside the spigot, fasten the screws.
STEP 1:
1.Loosen the M10 screws on the spigot with a wrenc h.
2.Insert the pole into the middle hole of spigot till to the end.
Screws
Pole
LEAVE A COPY FOR THE USER / MAINTENANCE ENGINEER
FOR FUTURE REFERENCE
5
STEP 4:
1. Get mains power supply cord into led driver compartment via
cable gland.
2. Lock the gland to mains power supply cord tightly.
3. For more details about wiring,please refer to the wiring instruction,
See Figure 6.
4. This Mako has 2 output options, and is set to 40W/5500 lm as
standard with the nominal output switch pointing at digit 0.To adjust
the Mako to the lower output 30W/4000 lm, adjust the nominal
output switch to point at digit 1 which will lower the drive current
and output.The output can be restored to 40W/5500 lm by
returning the switch back to digit 0.
502.5mm
200mm 71mm
STEP 3:
1. Loosen locking bolts and open the cover.
STEP 5:
1. Fasten the locking bolts on the cover tightly.
Screws
Locking bolts
Cover
Locking bolts
0°
Mains power supply cord
Bubble level
Cable gland
5500lm/4000lm Switch
by

MAKO Series LED Area Light
This logo indicates that this product must not be disposed of with other waste.
Please recycle used lamps to prevent environmental hazard and threats to human
health resulting from improper disposal.
Main specifications
2
Model No.
SL040MAKO
System Wattage
40W
Dimensions (L x W x H)
502.5mm (19.78") x 200mm (7.87") x 71mm (2.80")
Weight
5.88kg (12.9Ibs)
EPA*
0.076m
Ambient Temperature
-40 C to +50 C
Ingress Protection
IP67
Input Voltage: 120 to 277V~ 50/60Hz
The ingress protection of the fixture is IP67 if the mains supply cable's specification is H07RN-F 3*1.5mm2
www.tigerlight.com.au
6Electrical Connections
Terminal Block
L
G
N
LIVE
GROUND
NEGATIVE
LIVE-Brown
GROUND-Housing
NEGATIVE-Blue
Mains power supply
LED Driver
WIRING INSTRUCTION
STEP I: Connect the LIVE wire in the mains power supply cord to
the “L” marked hole In the terminal block and tighten the
connection properly.
STEP II: Connect the NEGATIVE wire in the mains power supply
cord to the “N” marked hole in the terminal block and
tighten the connection properly.
STEP III: Connect the GROUNDING wire in the mains power
supply cord to the “G” marked hole in the terminal block
and tighten the connection properly.
Common causes and solution
Encountered Problem Possible Cause Remedy
Module does not light up
Internal wire disconnected
LED driver failure
Module Failure
Open fixture and locate loose wires, reconnect connectors or wires
and close cover. And retest.
Open fixture and check for disconnected wiring. If all wires are fine,
replace LED driver with new one and test.
If all the above remedies are trialed then the light module has most
likely failed. Contact us for replacement and warranty information.
by