Saxby Lighting Varone 55702 Manual

• TheLEDbulbsinthisproductarenonreplaceable
Fitting/replacing bulbs
Instructionleaflet
Varone Recessed Bricklight
55702
www.saxbylighting.com
Live Voltages may be present in this unit even when turned off or when completely disconnected.Foryoursafety,
alwaysswitchoffthesupplybeforechanginglightbulbs,orcleaning.
Wasteelectricalproductsshouldnotbedisposedofwithhouseholdwaste.Pleaserecyclewherefacilities
exist.CheckwithyourLocalAuthorityorretailerforrecyclingadvice.
Recycling advice
Safety information
SaxbyLightingLtd.BH233PE
Werecommendcleaningwithasoftdrycloth.
Donotusesolventsorabrasivecleanersasthesecould
damagethefinish.
Iss.119032015
• Afterconnectingthesupplycabletotheterminalblock,
replacethefasciausingthe4screwsremovedearlier.
• Insert the light into the housing until the spring
clips lock into place. Ensure the shade is pointing
downwardstoavoidingstaringdirectlyintotheLEDs.
• Replacefuseor circuitbreaker andswitch on.Your
lightisnowreadyforuse.
Commissioning
TheLEDmoduleisprotectedbyashade.Theshadecannotbereplaced,iftheshade
becomescrackedordamaged,thisfittingmustbediscarded.

Thankyouforpurchasingthislightfitting.Pleasereadtheinstructionscarefullybeforeusetoensuresafeand
satisfactoryoperationofthisproduct.Pleaseretaintheseinstructionsforfuturereference.
Warning
This is a Class 1 product and must be earthed.
Pleasereadtheseinstructionscarefullybefore
commencinganywork.
Thisunitmustbefittedbyacompetentandqualified
electrician.
InstallinaccordancewithIEEWiringregulationsand
currentBuildingRegulations.
Topreventelectrocutionswitchoffatmainssupply
beforeinstallingormaintainingthisfitting.Ensure
otherpersonscannotrestoretheelectricalsupply
withoutyourknowledge.Ifyouareinanydoubt,
pleaseconsultaqualifiedelectrician.
Thislightfittingshouldbeconnectedtoacircuitwitha
30mARCDfitted.
Ifreplacinganexistingfitting,makeacarefulnoteof
theconnections.
Wasteelectricalproductsshouldnotbedisposedof
withhouseholdwaste.Pleaserecyclewherefacilities
exist.Checkwithyourlocalauthorityorretailerfor
recyclingadvice.
Thislightfittingcontainsnon-replaceablepartsand
cannotbeserviced.
Ifdamageoccursthepartshouldbediscarded.
ThisproductisratedatIP65.
Thisproductisnotsuitableforlocationinorneara
marineenvironment.
Thisproductisnotsuitablefordimming.
Specification
Voltage: 240V50Hza.c.
Lamp: 4WLEDmodule,30lm
IPrating: 65
Layout
• Planthedesiredlayoutofthisfittingcarefully,
ensuringthecableswillreachthedistancebetween
thejunctionboxandthelightfitting.
• Avoidlocatinganycablesinpositionsthatwould
causeahazard.Positioncablesandoutdoorrated
junctionboxes(notsupplied)awayfromareas
wheretheymaybeatriskfrombeingcut,trappedor
damaged.
• WerecommendthatyouuseH05RN-Fspecification
cable(notsupplied)whichisanoutdoorgrade,
rubbersheathedcable.Themainssupplycablemust
haveaminimumcrosssectionalareaof1.0mm²
• Cablesmustbeprotectedusingsuitableconduitor
plastictrunking.
Existingfittingsmustbecompletelyremovedbefore
installationofanewproduct.Before removing the
existing fitting, carefully note the position of each set
of wires.
• Theproductcomeswithahousingunitthatmustbe
fittedintotheholepriortoanywiringtakingplace.
• Cutthemountingholefortheunittakingcarenot
todamageanypipesormainscablesbeneaththe
mountingsurface.
 -95mmx95mmcutout,65mmvoiddepth
Knockoutasuitablecableentryholeandpullthesupply
cablethough.
•Fitthehousingintopositionandsecure.This
surroundmaybecementedinposition.Waituntil
thecementhassetbeforecontinuingwiththe
installation.
• Unscrewthe4screwsaroundthefasciatoaccess
theterminalblock.Feedthesupplycablethroughthe
metalglandandconnectasbelow.
Installation
• Youhavecorrectlyidentifiedthewires
• Theconnectionsaretight
• Noloosestrandshavebeenleftoutoftheconnection
block.
Havingcorrectlyidentifiedthewiringfromyourexisting
lightfitting,pullthewirethroughtheholeandconnectto
theconnectionblockinsidetheproductinthefollowing
way:
Wiring
Check that...