tiki SHB10 User manual

09-02-2021
30122
SHB10 TIKI
Installation and User manual
Indoor module for
air to water split systems

3SHB10 TIKI
Table of Contents
1 Important information _________4
Safety information ______________________4
2 Delivery and handling__________6
Available models _______________________6
Compatibility __________________________6
Transport _____________________________6
Assembly_____________________________6
Installation location _____________________7
Removing the cover _____________________7
Supplied components ____________________7
3 Design of the indoor unit________ 8
SHB10_______________________________8
Dimensions and pipe connections ___________10
4 Pipe connections _____________11
General information _____________________11
Docking the indoor unit___________________13
Installation alternative ___________________17
Hot water circulation ____________________19
Temperature sensor installation on pipe _______19
System diagram ________________________19
5 AMS 10 outdoor unit __________22
Delivery and handling ____________________22
Installation ___________________________22
Lift from the street to the set-up location ______22
Lift from the pallet to final positioning ________23
Scrapping ____________________________23
Condensation water drain _________________23
Recommended alternative for leading
o condensation water ___________________23
Dimensions ___________________________25
Installation location _____________________28
Sound power levels _____________________28
6 Electrical connections _________29
General information _____________________29
Connections___________________________30
Settings______________________________32
7 Commissioning and adjusting ____33
Preparations __________________________33
Filling and venting ______________________33
Circulation pump _______________________34
Commissioning_________________________34
Start Guide ___________________________34
8 Control - Introduction _________36
Display unit ___________________________36
Menu system__________________________37
9 Control ____________________39
Menu 1 - INDOOR CLIMATE________________39
Menu 2 - HOT WATER____________________40
Menu 3 - INFO _________________________40
Menu 4 - MY SYSTEM ___________________41
Menu 5 - SERVICE ______________________42
Start guide____________________________43
Settings for the user_____________________45
Cooling settings ________________________54
Submenu SERVICE ______________________54
10 Service ___________________61
Service actions_________________________61
11 Disturbances in comfort _______65
Troubleshooting ________________________65
Additional heating only___________________66
12 Accessories________________67
Connecting the KVR accessory______________68
Connection of an additional GP10 pump _______69
13 Technical data ______________70
Dimensions and layout of connections ________70
Technical data _________________________71
Energy eciency label ___________________73
Energy eciency specifications of the package __74
Energy label___________________________75
Electrical wiring diagrams_________________79

4SHB10 TIKI
1 Important information
Safety information
Serial number
Symbols
Marking
SHB10 is CE marked and has an
IP21 protection rating.
The CE mark confirms that TIKI
has ensured that the product
conforms to all applicable regula-
tions specified by the relevant EU
directives. The CE mark is man-
datory for most products sold in
the EU, regardless of where they
are made.
IP21 means that objects with a
diameter greater than or equal to
12.5 mm cannot penetrate and
cause damage and that the prod-
uct is protected against vertically
falling drops of water.
This appliance can be used by
children aged 8 years and above
and persons with reduced phys-
ical, sensory or mental capacity
or lack of experience and knowl-
edge, if they will be supervised
or have received instruction
concerning safe use of the ap-
pliance, and if they understand
the danger involved in its use.
Children must not play with the
appliance. Cleaning and basic
maintenance of the appliance
must not be carried out by chil-
dren unsupervised.
The rights to make structural
changes are reserved.
©TIKI 2021
This manual contains installation
and service procedures for imple-
mentation by specialists.
CAUTION
This symbol indicates danger
to the appliance or person.
NOTE
This symbol indicates im-
portant information to note
while operating or main-
taining the appliance.
TIP
This symbol indicates tips
that will make it easier to
operate the product.
Section 1 | Important information
Serial number
SHB10
(PF3)
Software
serial number
(PF4)
The serial number is located in-
side the SHB 10, under the control
panel and consists of 14 digits.

5SHB10 TIKI Section 1 | Important information
Waste disposal
Leave the disposal of the
packaging to the installer
who installed the product
or to a special waste dis-
posal facility. Improper disposal of the product by
the user may result in administrative
penalties in accordance with the ap-
plicable legislation.
Do not dispose of used products
with normal household waste. It
must be transported to a special
Description Notes Signature Date
Heating medium
Flushing the system
System vented
Expansion vessel
Particulate filter
Safety valve
Shut-off valves
Pressure in the climate system
Connected according to outline diagram
Hot water
Shut-off valves
Mixing valve
Safety valve
Electric power supply
Connecting communication
Perimeter protection
Protection, indoor unit
Building protection
Outdoor temperature sensor
Room sensor
Current sensor
Safety circuit breaker
Residual-current device
Setting the thermostat to emer-
gency mode
Miscellaneous
Docked to
Inspection of the installation
The climate system must be inspected before commissioning. The inspection must be carried out by a suitably
qualified person. In addition, fill in the page for the installation data in the User Manual.
Checklist
waste disposal facility or to a ven-
dor who provides this type of ser-
vice.

6SHB10 TIKI
2 Delivery and handling
Transport
Available models
Compatibility
Assembly
The SHB10 unit can be used with Split type outdoor
units. The compatible SPLIT heat pumps are:
Outdoor unit Compatibility
AMS 10-6 SHB10-6
AMS 10-8 SHB10-12
AMS 10-12
AMS 10-16 SHB10-16
Section 2 | Delivery and handling
SHB10 units include the following separate models:
• SHB10-6- unit dedicated for use with AMS 10-6.
• SHB10-12- unit dedicated for use with AMS 10-8
and AMS 10-12.
• SHB10-16- unit dedicated for use with AMS 10-16.
CAUTION
When the SHB 10 is stored or transported horizontally
with the display facing up, no devices / components
may be stored on top of the unit. It may damage the
device.
1. Place the included mounting hanger horizontally
against the wall. Level the hanger using the spirit
level. Mark the points for the mounting holes to
be drilled.
• SHB10 is equipped with wall-mounted hanger. For
mounting hole spacing, see drawing below.
• SHB10 must be hanged on walls of sufficient
load-bearing capacity able to take the weight of
a filled indoor unit.
• Since SHB10 is equipped with condensate drain-
off system, the indoor unit must be installed at
the site with sewage system drain.
CAUTION
The SHB10 unit must be hanged on the wall using
the included hanger. The device can be installed in
vertical position only.
130mm 130mm
2. Drill the holes in marked points.
3. Screw the attachments to the wall using the pro-
vided rawplugs and bolts.
4. Install SHB10 on the mounted hanger.
5. Level the device using the bottom adjustment
screws.
CAUTION
Included rawplugs should be assessed in terms of
load-bearing capacity and material of the wall on which
the device is to be hanged. Replace with the other
rawplugs meeting the requirements, if necessary.
More information on SPLIT heat pumps available at
www.tiki.si and in dedicated installation and user
manuals.
See section "Accessories" for the list of accessories
to be used with SHB10.
The SHB 10 indoor unit should be transported and
stored vertically or horizontally on the rear wall with
the display facing up. Storage location must be dry.
SHB 10 can be transported into the building vertically
or carefully placed on the rear wall with the display
facing up.

7SHB10 TIKI
Supplied componentsInstallation location
Removing the cover
Safety group with safe-
ty valve (3 bar), pressure
gauge and automatic air
vent (1 pc.)
230V connection
jumper (1 pc.)
Hanger (1 pc.)
CAUTION
The rated opening pressure of the safety valve is 3
bar.
Section 2 | Delivery and handling
Outdoor
temperature sensor
(1 pcs)
Indoor
temperature sensor
(1 pcs)
• Hanger (1 pc.)
• Rawplugs and bolts (3 pcs)
• Safety group (1 pc.)
• Outdoor temperature sensor (1 pcs)
• Indoor temperature sensor (1 pcs)
• 230V connection jumper (1 pc.)
• Temperature sensor BT (3 pc.)
• Instalation and user manual
SHB10 can be installed in any room protected against
temperature drop below 0°C to avoid freezing of the
heating medium. 800 mm of free space should be
ensured in the front of the indoor unit. All servicing of
SHB10 can be performed from the front.
1. Unscrew the bolts from the lower edge of the
front cover 1.
2. Tilt the cover at the edge, making sure that the
connection cables are not damaged and discon-
nect the cable grounding the front cover 2.
3. Disassemble the front cover by tilting its lower
edge toward you 3and lifting it up 4.
Min. 30 cm
Min. 20 cmMin. 20 cm
CAUTION
After reassembling the cover, the earthing wire must
be connected.
4
3
Temperature sensor
BT
(3 pc.)

8SHB10 TIKI
3 Design of the indoor unit
SHB10
X10
X0
X1
FA2
FA3
GP12
AA27
AA2:X4
AA2:X4
AA2:X15
AA2
K2
EP2
BT12
CM1
BP4
BT15
BT63
BT3
BT30
EB1
FD1
AA23 AA3
K1A-K3A
FA1
XL11
SF1
X2
AA7
BT71
BT25
QN10
XL8
WM1
XL10
XL14
XL13
Section 3 | Design of the indoor unit
XL2
XL1
UB4
PF3
PF4
PF2
PF1
UB3

9SHB10 TIKI
HVAC components
CM1 Expansion vessel, closed
QN10 Reversing valve, hot water/climate system
GP12 Circulation pump
EP2 Heat exchanger
Sensors
BP4 Pressure sensor, high pressure
BT3 Temp. sensor, condenser return
BT12 Temp. sensor, condenser out
BT15 Temp. sensor, liquid refrigerant
BT25 Temp. sensor, heating medium supply
BT63 Temp. sensor, supply heating medium be-
hind immersion heater
BT71 Temp. sensor, heating medium return
Elementy elektryczne
X0 Terminal block- 230V~ / 400V~
X1 Terminal block- 230V~
X2 Terminal block- 230V~
X10 SPLIT Terminal
AA2:X4 Terminal block- low voltage
AA2: X15 Terminal block- low voltage
K1A-K3A Contactor for electric additional heat
K2 Alarm relay
BT30 Standby mode thermostat
AA2 Main board
AA3 Input board
AA23 Communication board
AA7 Extension card
AA27 Relay board
FD1 Thermal circuit breaker
FA1 Miniature circuit breaker (protecting the
indoor unit)
FA2 Miniature circuit breaker (protecting the
outdoor unit)
FA3 Miniature circuit breaker (protecting the
STB and power)
EB1 Electric additional heat
Various
SF1 Controller switch
Pipe connections
XL1 Connection, heating medium, supply
XL2 Connection, heating medium, return
XL8 Connection, heating medium hot water,
supply
XL10 Connection, drain valve
XL11 Connection, safety assembly,
pressure gauge
XL13 Connection, liquid refrigerant
XL14 Connection, gas refrigerant
WM1 Condensate drip tray drain
Section 3 | Design of the indoor unit
UB1 Rear left cable groomet
UB2 Rear right cable groomet
UB3 Lower left cable groomet
UB4 Lower right cable groomet
PF3 Serial number SHB10
PF4 Software serial number
PF1 Nameplate
PF2 Plate with the designation of the hydraulic
connections

10 SHB10 TIKI
Dimensions and pipe connections
XL8
XL11
WM1
XL10
XL14
XL13
515
345850
484,5
414
316
218,5
149
34
43
80
133
218
Section 3 | Design of the indoor unit
XL2
XL1
PF1 Nameplate
PF2 Plate with the designation of the hydraulic
connections
WM1 Condensate drain from the drip tray
PF1
PF2
Pipe connections
XL1 Connection, heating medium, supply
Ø22 mm for SHB10-6 and SHB10-12,
Ø28 mm for SHB10-16
XL2 Connection, heating medium, return
Ø22 mm for SHB10-6 and SHB10-12,
Ø28 mm for SHB10-16
XL8 Connection, HW heating medium, supply
Ø22 mm for SHB10-6 and SHB10-12,
Ø28 mm for SHB10-16
XL10 Connection, GW1/2” drain valve
XL11 Connection, safety assembly
Ø22 mm, pressure gauge
XL13 Liquid refrigerant
Connection 1/4" (SHB10-6)
Connection 3/8" (SHB10-12 / SHB10-16)
XL14 Gas refrigerant
Connection 1/2" (SHB10-6)
Connection 5/8" (SHB10-12 / SHB10-16)
Other information