Timbertech Loll Designs Adirondack Chair User manual

*Bolt shown
actual size
INCLUDED PARTS
1˝
BOLT
18x
LEFT LEG
1x
RIGHT LEG
1x
CB
4x
P16
1x
GB
12x
P9
1x
P7
1x
BACK
1x
P2
1x
P5
1x
P6
1x
P5
PRODUCT CARE Your new furniture is a very low maintenance product. You’ll never need to paint or stain it and it can
be left outside all year regardless of the season. However, we are pretty sure your furniture will get a lot of use and will at some point need cleaning. We recommend using clean water from a faucet or
garden hose and incorporating a soft bristle brush to remove light dirt or spills. Adding a tablespoon
or two of your favorite eco-friendly soap to the wash will get everything squeaky clean. Removing mineral deposits from hard water or other tougher cleaning jobs can be done with TimberTech Deck Cleaner which is specially formulated for this type of cleaning.
WARRANTY TimberTech is known for making beautiful, high-quality, outdoor living products that last and our Invite Collection of Outdoor Furniture is no exception. We want you to be happy that you chose our furniture and satisfied with your purchase and we back that up with a comprehensive Warranty. Please see the TimberTech + Loll Invite Collection Warranty for complete details.
PRODUCT DAMAGED IN SHIPMENT
Sometimes accidents happen. Please inspect your furniture when you receive it to make sure that it has not been damaged during shipping. If damage has occurred, please take digital pictures of the damaged furniture and the box it was shipped in, and call Customer Service using our toll free number: 877.275.2935. The damage will be assessed and you will be contacted with a solution to the problem. If there is any damage, please save all of your packaging material in case a return is necessary.
ASSEMBLY TIPS Please read before beginning assembly and be sure to wear eye protection to
avoid injury, particularly if using power tools
To avoid damaging the furniture, perform the assembly of your new furniture on a clean, soft
surface like a blanket, carpet, or the flattened cardboard box the furniture was shipped in. When removing the furniture from the carton and if using the carton for an assembly surface, please CAREFULLY remove all staples that held the shipping carton together. These can scratch you and the furniture and we don't want that to happen to either of you. Components should not be unnecessarily forced together! If it seems parts aren’t fitting together you likely have something wrong and you should reread the instructions to ensure you are aligning the proper components. The various “Blocks” used in assembly may have a protective film on one side. This surface is hidden after assembly so the film can remain on the Block or it can be removed. Although not recommended, you may use a cordless screw gun or drill if you have one and know how to use it properly. Set the clutch setting at low/ medium torque. We do not recommend using an electric drill with a cord or without a clutch to install bolts in inserts as you can easily overtighten and damage the product. All bolts come standard with a thread- locking compound pre-applied to reduce loosening of the bolts over time. Start all bolts by hand and then use the Allen Key/Hex Wrench to tighten until parts are drawn tightly and firmly together.
**Please recycle the cardboard box and all paper and plastic packaging materials. BLOCK & BOLT INSTALLATION Insert bolts through countersunk hole side of blocks as shown below. When done properly, the top of the bolt will sit even or flush with the top surface of the block.
Allen Key/Hex Wrench Install Tool Included in the carton for use in tightening all bolts..
CORRECT INCORRECT
We want you to love your new furniture. Reach out if you need assistance.
1.877.275.2935 1330 W Fulton Market, Suite #350, Chicago, IL 60607
Countersunk
Hole
ASSEMBLY INSTRUCTIONS & PRODUCT INFO: | ADIRONDACK CHAIR
G-BlockC-Block
P8
1x

4 p e t S
1
2 3
4
1 ep St
3 ep St
LEFT
LEG
P7
P5
P8 P9
GB
1x
1˝
BOLT
18x
T
˝
BOL
1
18x
T
˝
BOL
1
1˝
BOLT
1x
1˝
BOLT
1x
1x
1˝
BOLT
GBGB
GB

5
6
7
1x
1˝
BOLT
2x
1˝
BOLT
P6
BACK
P2
GB
GB
GB

8
9
10
5x
1˝
BOLT
4x
1˝
BOLT
CB
4x
RIGHT
LEG
GB
5x
P16
2x
1˝
BOLT