hygena 314/5041 User manual

Issue 1 - 10/10/14

Wall
Shelf Support Catch Plate x 1 14mm Screw x 2
Tools required

and
in 1
23
2
2 3
and
2. Glue and insert 16 x
wooden dowels R into
bottom 4 & Front bar 5
in
45

Use a screwdriver to turn the
female camlock clockwise to
lock.
“Using Camlocks”
section at the front of this
instruction for further
assistance.
Please refer to the
5
4
4&
5 2
4

Use a screwdriver to turn the
female camlock clockwise to
lock.
“Using Camlocks”
section at the front of this
instruction for further
assistance.
Please refer to the
3
4&5
4
1
Catch plate
10
10
as shown

Use a screwdriver to turn the
female camlock clockwise to
lock.
“Using Camlocks”
section at the front of this
instruction for further
assistance.
Please refer to the
L
1
2 3
2
3
4
9
10
to the reverse of
the unit with 16 x screw
in position shown.Use a
Phillips Screwdriver to
tighten
L

7
8
4 x
7
8
2. Cover visible camlocks
with 4 x stickers N as
shown

6
1. Using 2 x screw &
washer secure 2 x wall
straps to the back of
left back & right back
9 10

It is recommended that the
unit is fixed to a wall.
1.Move the unit into desired
position.
2. Mark the wall with a
suitable scribe the position
of the fixing holes.
3. Drill 2 x 7mm hole and insert
2 wall plug .
4.Secure the other end of the
straps to the wall with 2 x
washer & screw
Note: To hide the strap behind
the unit ,drill the hole lower
than the top of unit.
Warning:
Before driling,check
wall for hidden pipes
and cables.
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800
Assembly Complete

A Guide to Wall Mounting & Fixings
lmportant note:
lf plastic wall plugs(rawl plugs)
are supplied with your product,
e.g.:
- these are only suitable for use in
masonry walls.
lf you are in any doubt about the
correct wall plugs for your wall,
seek professional advice.
Failure of the product due to
using the incorrect fixings is the
responsibility of the installer.
lmportant: when drilling into walls always check
that there are no hidden wires or pipes etc.
Make sure that the screws and wall plugs being used are suitable for
supporting your unit.Consult a qualified tradesperson if you
are unsure.
Hints:
General rule: always use a larger screw and wall plug if you are
not sure.
Ensure you use the recommended drill bit to match the wall plug and
hole size.
Ensure you drill the hole horizontally; do not force the drill or enlarge
the hole.
Take extra care when drilling high walls,ceilings and ceramic tiles.
Ensure wall plugs are inserted beyond the thickness of the ceramic
tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
Types of walls You can use one of the folllowing types of wall plug if your walls are made
of brick, breeze block, concrete,stone or wood.
No.1"General Purpose" wall plug No.3"Cavity Fixing" wall plug No.5"Hammer Fixing" wall plug
Generally aerated blocks should not
be used to support heavy loads,use
a specialist fitting in this case. For
light loads, general purpose
wall plugs can be used.
For use with plasterboard partitions
or hollow wooden doors.
For use with walls stuck with
plasterboard. The hammer fixing
allows it to be fixed to the wall
rather than the plasterboard.
Always check the fixing is secure
to the retaining wall.
No.2" Plasterboard"
wall plug
No.4" Cavity Fixing - Heavy Duty"
wall plug
No.4" Shield Anchor" wall plug -
heavy loads
For use when attaching light loads
onto plasterboard partitions.
or use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
For use with heavier loads such as
TV and HiFi speakers and satelite
dishes etc.
lf you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800