TIMEDOX Silver Plus User manual

HR Monitoring and Time-clocks
QuickStart Guide
For Timedox US Silver Plus
This QuickStart Guide provides guidelines regarding:
•How to mount the Time-clock onto a wall
•How to set the date and time
•How to add employees and punch In and Out
•How to connect the Time-clock via the Ethernet and USB
•Featured tips on getting the most of your Time-clock
Timedox US provides account administration with customer service and
technical setup consultation for all devices.
The complete user guide and applications are available via our web site
https://www.timedox.us/
To login: Press CONTACT, select SUPPORT and enter the Password: 4705547334
To contact us: email [email protected] | Ph. 470-554-7334
For further information on any issue related to this guide, please refer to the
Timedox User Guide

Page 2
Package Contents
Each Timedox package consists of the following:
a) Time-clock
d) 1 Mounting Plate
g) 4-count large Phillip screws
b) 1 A/C Power Adapter
e) 1 Small Black
Screw
❖1 Proximity card sample
c) 1 Ethernet Cable
f) 4-count dry-wall screw anchors
Should any item be missing, call our toll-free customer support at 1-470-554-7334
A
Fingerprint protection sticker
D
E
F
G
C
B

Page 3
Mounting the Time-clock onto a wall
1. Verify the availability of an electrical outlet and an Ethernet port.
2. Place the mounting plate at the desired height –up to four (4) feet from the Ethernet
port –and mark the four (4) holes on the wall (See the middle figure below).
3. Drill the four (4) holes and insert the count dry-wall screw anchors.
4. Place the mounting plate on the wall and fasten it to the wall using the large Phillip
screws (See the middle figure below).
5. Connect the Ethernet cable and AC Power cord to the Time-clock (See the right figure
below).
6. Slide the Time-clock into the mounting plate (See the left figure below).
7. Connect the Ethernet cable to the designated port on the wall.
8. Plug the A/C power adapter into the wall socket.
9. Fasten the mounting plate to the Time-clock using the small black screw (See the
figures below).
10. Remove the fingerprint protection sticker.
Small
black
screw
Large
Philip
screws
Finger
Protection
Sticker
Ethernet
cable
Power
cord

Page 4
Setting Date and Time
1. Press to power up the Time-
clock.
2. Press-and-hold to display the
main menu
3. Select System and then select
Date/Time.
4. Set the date and time, using the
keypad and arrows.
5. Press to save settings.
6. Press ESC to return to the main
screen.
7. Verify that the date and time are
correct.
Adding and Enrolling Employees
1. Press-and-hold to display the
main menu.
2. Select User and then select Add User.
3. Define the following the settings:
ID
ID
Name
ID
4. Choose and fill-in one of the following
options:
FP
(Fingerprint)
Verify that the protection sticker has been removed.
Place and lift desired finger three times, as instructed.
PWD
(Password)
Enter a 4-8 digit PIN.
Card
Wave the card over the Time-clock top-right across the double line.
5. Press ESC until the main screen is displayed.
6. To test the settings, clock in by your chosen option:
FP
Place the registered finger on the sensor, covering the entire surface.
PWD
Using the number keypad, enter your ID number and then your PWD.
Card
Slowly wave the proximity card once over the fingerprint sensor surface.
7. For each employee, repeat instructions 4-6.
Note: Timedox automatically registers the first punch as IN and the following one as OUT.

Page 5
Data Transfer Options
The Timedox Silver Plus offers two standard connection options for transferring data.
Choose your preferred option below and follow the relevant instructions.
Connection Option
Requirements
Network Connection
(Recommended)
Available network and Ethernet Port
USB Connection
A compatible USB 2.0+ storage device
Note: Choose your connection option before proceeding.
Connect via your Network
1. Verify that the Ethernet cable is connected to the Time-clock and wall designated ports.
2. Press-and-hold to display the main menu.
3. Select System and then select Comm.
4. Use the arrows to select the DHCP option and turn it to ‘on’, and then press
5. Remove the power cord from the timeclock for 30 secs, and then replace it.
6. Press to power the timeclock back on and repeat steps 2 & 3.
7. Find the IP address (and other options) and note down the IP address here:
_________________________
8. Download the application named OfflineDeviceManager from the Timedox support
page. (See Page 1 for intructions on accessing the support page)
9. Luanch the application and enter the password ‘Timedox’
10. Select add Device and follow the screen prompts/
Download via the PC –USB
1. Connect your USB device to the port on the left side of your Time-clock.
2. Press-and-hold to display the main menu.
3. Select Data Mgt. and then select Download Attlog.
4. Wait for files to be downloaded to the device.
5. Connect the USB to the PC.

Page 6
Setting the Timedox Excel File
1. Download the Timedox Excel file from the Timedox Support Page:
EmployeeReportManager_1.0.X.X.xls
(See Page 1 for intructions on accessing the support page)
2. Press .
3. Define the Company and Payroll Settings.
4. Import the attlog.log file from the Time-clock or the USB.
5. Enter the employees' names and hourly rates.
6. Save.
7. Import the attlog.log file again and verify that all the changes are saved.
Need Help?
Call us toll-free at 1-470-554-7334 or
Send an email to [email protected] for support