TimeTec PANIC BUTTON User manual

www.i-timetec.com
User Guide
PANIC BUTTON
GET HELP WHEN YOU NEED IT MOST

2
www.i-timetec.com
TimeTec Panic Button
PRODUCT BRIEF
TimeTec Panic button is activated by the push-button function. Under
all circumstances, this emergency STOP switch can only be turned off
manually. This device is strongly recommended to be used only in the
case of an emergency. The alarm will be triggered immediately once
the Panic button has been pressed.
FEATURES
Emergency Alarm
Low Battery Reminder
Tamper Proof Security Alarm

3
www.i-timetec.com
TimeTec Panic Button
INSTALLATION METHODS
INSTRUCTION FOR ADHESIVE INSTALLATION:
1. Clean the adhesive surface area using a detergent to remove dust,
grease, and other dirty stains on the surface.
2. Make sure the surface is dry before sticking the item onto the sur-
face
3. Remove the 3M adhesive release liner with care. Do not press your
finger against the 3M adhesive sticky surface while removing the
release liner. While pasting, apply adequate pressure to the adhe-
sive surface for a longer-lasting adhesive result.
Remark:
The bonding temperature for 3M adhesive is best between 12-38 Celcius. Please avoid
carrying out this process in any environment that is below 10 Celcius.

4
www.i-timetec.com
TimeTec Panic Button
1. Device Registration
After the TimeTec Gateway Camera is turned on, log into i-TimeTec
App on your mobile phone, click the “+” from the Smart Home page
to add devices, scan the QR code on the back of the TimeTec Panic
Button, and follow the instructions of the App. Add the Panic Button
under TimeTec Gateway Camera.
After triggering the Panic button, it will automatically register itself
with the TimeTec Gateway Camera and can be used directly upon
successful registration. (The “Device List” can be refreshed and
checked on the page of TimeTec Gateway Camera. Registration suc-
cess or failure will be determined by the approval sign with the Panic
Button icon.)
If the device is being transferred or updated to a newer version of
TimeTec Gateway Camera at a later stage: After deleting/transferring
the device, press and hold the Panic button for no less than 10 sec-
onds until the indicator light fades out. Press the Panic Button again
for new registration.
2. Alarm
The emergency alarm will be triggered once the Panic Button is pressed.
A notification will be sent instantaneously to the mobile phone App. To
stop the alarm from beeping, press the button for 3 seconds, and release
once the indicator light begins to flash.
INSTRUCTIONS

5
www.i-timetec.com
TimeTec Panic Button
3. Low Battery Reminder
When the Panic Button battery power is running low, a message will
be auto-generated and send to the i-TimeTec App for mobile notifi-
cation.
4. Tamper Proof Security Alarm
After the tamper switch of the Panic button is triggered, a message
will be auto-generated and send to the i-TimeTec App for mobile no-
tification.

6
www.i-timetec.com
TimeTec Panic Button
Q1. No siren alert on App after Panic Button is pressed
A:
The Panic Button is not fully registered, please add the device on the APP
and restart the registration process again.
Replace faulty devices.
Check the battery power and replace if necessary.
2. Please follow the instructions for proper installation and usage. Handle
with care during installation to avoid dropping or hitting the device that
may damage the internal components.
3. This product can reduce the occurrence of accidents, but there is no fool-
proof guarantee. For safety caution and to use this product correctly, it
is recommended that you stay vigilant and strengthen the awareness of
safety precautions practice.
4. Do not frequently disassemble this device, avoid repair and/or replace its
original components, this can cause serious damage to the product. Any
questions or help required, please email us at [email protected]
Q&A AND TECHNICAL TIPS
© 2019 Timetec Cloud Sdn Bhd. All rights reserved • 112019

© 2019 Timetec Cloud Sdn Bhd. All rights reserved • 112019
www.i-timetec.com