Tisira TIS60B User manual

www.tisira.com
SERVICE MANUAL
600 // INDUCTION HOB - SLIDE
TIS60B
DISCLAIMER // THE INFORMATION CONTAINED IN THIS SERVICE MANUAL IS INTENDED
FOR LICENSED PERSONNEL ONLY. PLEASE CONTACT ARISIT FOR FUTHER INFORMATION
[AUST] 1300 762 219 [NEW ZEALAND] 09 306 1020
Version 4.1

Exploded View
tisira | TIS60B pg 1/5

Parts List
tisira | TIS60B pg 2/5
ID PART NUMBER DESCRIPTION
1 G-TIS60B Glass Asembly
2 / 24 541600200011 Ceramic Plate Temperature Sensor 275mm (3-pin connector)
**17466000000194 **Ceramic Plate Temperature Sensor 275mm (2-pin connector)
3 303203501131 Hot Plate (220) 2300/2600W 220-240V
4 541400300009 Radiator Board
6 541410500003 Bracket
7 541700300005 Insulation Panel (B)
8 541500200005 Accessory Power
9541500000047 Power Board (3-pin connector)
**17166000000239 **Power Board (2-pin connector)
10 541600100004 Cooling Fan
11 541810000001 Junction Port Holder
13 541800000017 Power Cord
14 303207300213 Fixed Board (Power Wire Clamp)
15 541300100005 Base
16 541300600009 Power Cord Case Cover
17 303207300215 Insulating Panel
19 303207300212 Wire Clamp
20 303207300211 Knighthead (Board Clip)
21 541700300021 Insulation Panel (A)
22 541500100036 Display Board
23 542300300004 Hot Plate (140) 1200/1500W 220-240V
25 541300600005 LED Cover
26 541700200008 Silicone Seal
27 541400200015 Heat Insulating Bracket
28 541700700001 Supporting Foam
** The power board design was amended in 2014:
Old part number: 541500000047 (3-pin connector)
New part numeber:
17166000000239 is suitable from serial numbers MA-04440-XXXXX (Feb 2015).
NOTE 1: These two power boards are not interchangeable. (3 and 2-pin connectors)
NOTE 2: The change from a 3 to a 2-pin connector also affects one of the Temperature Sensors
(541600200011). Please refer to codes listed in the table above. Items 2/24.

Wiring Diagram
tisira | TIS60B pg 3/5
L2 L1
N2 N1
L N
N
L
CN4
CN1
CN2
CN4
OUT4
OUT2
OUT1
OUT3
OUT4 OUT2
OUT1 OUT3
X1A
X2A
X3B
X3A
X11
FAN1
X9
X10
X7
X8
NTC
NTC NTC
NTC
Thermal� cut-out
Thermal�cut-out
Thermal� cut-out
Thermal� cut-out
FAN
Induction�
coil
Induction�
coil
Induction�coil
Induction�coil
CN5
CN2
CN7
CN4
CN3
CN2
CN3 CN4
CN7
CN5
1
1
1
POWER�IN

tisira | TIS60B pg 4/5
Trouble Shooting
Codes Description Possible Solutions
F3 - F8 Temperature Sensor Failure
• If the connections, wiring and connectors
have been checked, replace the
temperature sensor;
• If the problem persists, replace the
relevant main board.
F9 or
FA - FE
Temperature sensor of the
IGBT failure • Replace the relevant main board.
FC
Problems with the connection
between the display board and
the main board
• Replace the display board rst and if the
problem persists, replace the relevant main
board.
E1/E2 Abnormal supply voltage
• Checkiftheexiblepowersupplyis
damaged;
• Check if the power connection of the
power board and main boards are properly
connected;
• Discnect the left and right main boards
separately to identify if one of them is
the cause of the error code. Replace
the relevant main board if the problem
disappears when one of the boards is
disconnected;
• If the problem persists, replace the power
board.
E3/E4 Glass plate temperature is high
• Check if the error still occurs after the
cooktop has cooled down;
• If the problem persists, replace the
temperature sensor of the zone that was
being used;
• If the problem still occurs, replace the
relevant main board.
E5/E6 Temperature sensor of the
IGBT is high
• Check if the error still occurs after the
cooktop has cooled down;
• If the problem still occurs, replace the
relevant main board.
Error Codes
When a common malfunction occurs, the appliance displays error codes to direct you to the possible
cause of the problem. Please refer to the following table:

tisira | TIS60B pg 5/5
Trouble Shooting
Problem Possible Cause Possible Solutions
The cooktop
doesn’tturnON
No power.
• Check the electrical installation
(hardwired);
• Replace the display board;
• If the problem persists, replace the
power board.
Bad connection between
Accessory Power and
Display Boards
• Check connectors and wires.
• If that is not the case, replace the
Accessory Power Board
Display Board is damanged • Replace the display board.
Unresponsive
touch controls
Damaged display board or
low voltage being supplied
to the display board
• Replace the display board;
• If the problem persists, replace the
power board.
The cooking
mode indicator
comes on, but
the cooking
zone does not
start
Glass plate temperature is
high
• High ambient temperature or air
intake/air vent is blocked
Faulty Fan • Check if the fan is running normally.
• If not, replace the fan.
Damaged Power Board • Replace the power board.
Touch
controls work
intermittently
Buttons are not touching
the bottom surface of the
glass or the diplay board is
damaged
• Check if the buttons are tilted or
misaligned and if they are being
correctly supported by springs.
• If that is not the case, replace the
display board.
Two zones on
the same side
of the cooktop
(front and rear)
don’tworkand
display shows
“U”
Bad connection between
display board as respective
power board
• Check the connection
Damaged display board • Replace the display board
Damaged power board • Replace the power board
Common Scnearios
When a malfunction occurs and the cooktop doesn’t display any error codes, please refer to the
most common scnearios and their possible solutions listed in the table below:

CONTACT DETAILS
AUSTRALIA
ARISIT PTY LIMITED
40-44 Mark Anthony Drive,
Dandenong South, VIC 3175,
Australia
P // 1300 762 219
F // 03 9768 0838
[email protected]
NEW ZEALAND
ARISIT PTY LIMITED
PO Box 68-140
Newton, Auckland 1145,
New Zealand
P // 09 306 1020
F // 09 302 0077
[email protected]
Tisira is committed to ongoing research
and development. Every effort has been
made to ensure all information in this
service manual is correct at time of going
to print. Dimensions should be used as
a reference only and actual dimensions
should be taken from the physical product
only.
Manufacturer reserves the right to change
specifications without notice.
www.tisira.com