Tisira TGF64E User manual

USERMANUAL
GAS HOB
TGF64E | TGWF64E | TGWF93E
IMPORTANT // Please ensure that you read through this manual prior to installation and use. This
user manual contains important information to ensure optimal performance and keep you safe. Please
retain your proof of purchase, as this will be needed in the event that you require a warranty service.
Remember to keep this user manual for future reference.
www.tisira.com
Version 1.1

Content
Contents 2
Warning & Safety Instructions 3
Product Overview 4 - 5
Operating Instructions 6 - 7
Cleaning & Maintenance 8
Installation 9 - 15
Page 2 Gas Hob User Manual

Warning & Safety Instructions
IMPORTANT // To ensure best performance, avoid risk of damage or accidents.
Please read the operating instructions prior to first time use.
Important Safety Instructions
To maintain the efficiency and safety of this
appliance, we recommend that you do the
following:
•DO NOT USE OR STORE
FLAMMABLE MATERIALS NEAR
THISAPPLIANCE.
•DO NOT SPRAY AEROSOLS IN THE
VICINITY OF THIS APPLIANCE WHILE IT
IS IN OPERATION.
•DO NOT MODIFY THIS APPLIANCE.
•This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
•Young children should be supervised to
ensure that they do not play with the
appliance.
•Ensure adequate ventilation i.e. the use
of a rangehood when cooktops / other
appliances, burning gas or other fuelsare
in use.
•If the supply cord of this equipment is
damaged, it must only be replaced by
the manufacturer or its service agent or a
similarly, qualified person in order to avoid
a hazard.
•This appliance has been designed for indoor
domestic use only.
•NOT FOR USE IN MARINE CRAFT,
CARAVANS, OR MOBILE HOMES.
•Keep packaging out of reach of children at
all times. Toavoid burns, young children
should be kept away.
•This appliance is designed for domestic use
or use in similar environments by guests in
hotel or motel rooms, bed & breakfasts and
other typical living quarters. This does not
include common/ shared or commercial
facilities within hotels, motels or bed &
breakfasts.
•NOTICE // The manufacturer may not be
held responsible for any damage caused by
incorrect installation ornon-compliance
with the instructions in this manual.
Gas Hob User Manual Page 3

Product Overview
Page 4
Gas Hob User Manual
4 5 6 7
1. Burner positions
2. Glass or MetalSurface
3. Control Buttons
4. SmallBurner
5. MediumBurner
6. Large Burner
7. WOK Burner
8. Cast Grill
9. Enamel Grill
8
9

Product Overview
Gas Hob User Manual
Page 5
Burners
1. Burner cap
2. Inner burnercap
3. Outer burnercap
4. Burner head(diffuser)
5. Burner base(cup)
6. Ignition candle
7. Flame failure device (thermocouple)

OperatingInstructions
Page 6
Gas Hob User Manual
IMPORTANT // To ensure best performance,
avoid risk of damage or accident. Please read
the operating instructions prior to first time use.
This appliance is supplied with a spare data
plate label. Please attach it to an adjacent
surface for future reference if the labels on
the base of the cooktopare not visible after
installation.
NOTE // The metal components have a
protective coating, which may give off a slight
smellwhenheatedup forthe first time.This
smell and any vapors given off do not indicate
a faulty gas connection or appliance nor are
they health hazardous.
The gassupply is turned off
Ignition candle
Strongest flame
Weakest flame
Respective burner
The burners differ in size and power. Choose
the most appropriate burner for the diameter
of the cookware being used as specified on
the table below:
BURNER
PAN SIZES
min diameter
(mm)
maxdiameter
(mm)
Auxiliary
120
180
Semi-Rapid
180
200
Rapid
180
220
Wok
220
260
The positionof the correspondinggasburner is
indicated on each control knob.
1. Control knobs
The controlknob is used to ignite the burner
and regulate the strength of the flame.
ATTENTION // Operating the knob controls as
described below can cause damage to the
appliance:
•Switching on the burner without pressing
the control down.
•Switching on the burner by turning the
control clockwise.
•Switching the burner off by turning the
control anti-clockwise.
2. Lighting a burner
To light a burner, simply follow the steps:
1. Press the corresponding knob of the burner
youareabout to use all the wayin and,
then, turn it anti-clockwise until you reach
the ‘Strongest Flame’symbol.
2. Keep the knob pressed in fora few seconds
after the flameignites.

OperatingInstructions
Gas Hob User Manual
Page 7
NOTE // When one of the control knobsis
activated, sparks are generated on all burners of
the cooktop simultaneously.
CAUTION // If the flame is extinguished
unintentionally,turn off the gas with the control
knob, wait for at least 30 seconds for the gas to
dissipate and try to light it again.
3. Switching off
To turn off a burner, simply turn the knob
clockwiseuntilit stopsundertheOFFsymbol“ ”.
Thisstopsthe flow of gasand the flame goesout.
4. Interruption to the electricity
supply
In the eventof a powercutthe flame can be
ignited with a match by following the steps:
1. Press the corresponding knob of the burner
you are about to use all the way in, then
turn it anti-clockwise until you reach the
‘Strongest Flame’symbol.
2. Whilepressingthe controlknobin, light the
gas at the burnerwith a match.
3. Keep the knob pressed in for afew seconds
after the flameignites.
5. Regulating the flame
IMPORTANT // Adjust the flame intensity so that
it does not spreadout beyond the side of the pan.
Thetipsoftheflamesaremuchhotterthanthe
centre,so they should stay beneath the pan base
fora best efficiency and a lower risk of injuries
and damages on pan handles.
The flame can be regulatedforany levelbetween
the strongest andweakestflame symbols.
•Cookware should be positioned aligned
with the centreof theburner.
•Do not use round-bottomed pans (eg.
Woks) without an appropriate wok support
recommendedby themanufacturer.
6. Flame failure device
This appliance is fitted with a thermo-electric
flame failuresafetydevice that cutsoff the
supply of gasto a burner if the flame goes out,
for example, when water boils over the burners
or sudden draughts occur.
The flame failure device operates
independently from the electricity supply. This
meansthat it will stillwork if the cooktopis
used during a power cut.

Page 8
Gas Hob User Manual
Cleaning &Maintenance
IMPORTANT // Before cleaning your oven, or
performing maintenance, turn the appliance
off and disconnect it from the power supply.
Also allow the appliance to cool down before
touching the unit.
Cleaning your appliance frequently will
extend its life. When cleaning your gas
cooktop:
•Do notusea steam cleaningapplianceto
cleanthisappliance.
•Use a soft cloth,warmwaterand neutral
soap to clean enameled, castiron and
stainless steelparts.
•Use a soft dry cloth to dry surfacesthat have
been cleaned with water.This will prevent
the occurrenceof watermarksand limescale
deposits.
•Do not use cleaning productscontaining
descalingagents.
•Do not use hard, abrasive brushesor
sponges.
NOTE // Always clean the appliance
immediately after any food spillage.
Cleaning the Burners
The removable parts of the burners can be
disassembled for a more thorough cleaning.
1. Remove the burner caps and burner
diffusers by pulling them away from the
burner cup.
2. Soak them in hot water with a small
amount of washing detergent.
3. Softly scrub off any remaining pieces of
food.
4. Rinse the parts, wipe and dry them.
5. Wipe the fixed parts of the burner cup with
a damp cloth, drying it afterwards with a dry
cloth.
6. Before placing the burner cap and diffuser
back in position, make sure that the flame
apertures are clean and completely dry.
IMPORTANT // Make sure that the ignition
candle and the probe of the thermo-electric
flame failure device extend through their
respective holes in the burner diffuser. Once
the burner diffuser is clicked into place
correctly, place the burner cap on top of
it. The burner cap should not rotate when
correctly positioned.
Servicing the cooktop
Always refer servicing to an authorised
service person. It is recommended that the
appliance be serviced every five years to
ensure the cooktop continues to operate
correctly and safely.
NOTE // If the appliance cannot be adjusted
to perform correctly, it is an abnormal
situation and you should contact the
authorised service provider.

Installation
Gas Hob User Manual
Page 9
IMPORTANT // Thisunitmustbeinstalledbyauthorised personnelandused onlyinpermanently
ventilatedrooms in accordance with the requirements of AS 5601 (gas installations), wiring code,
manufacturer’sinstructions, localand national authority and any other statutoryregulations.
Follow carefully the safety instructions and clearance requirements given below.
NOTE // The dimensions presented in this manual are given in millimetres (mm).
IMPORTANT // The veneer or laminate coatings of worktops(or adjacent kitchen units) must be
treatedwith 100 °C heat-resistantadhesive which will not dissolve or distort.
A minimum safety clearanceof 25mm underneath the cooktopmust be provided for the
installationof the flexible gas connection hose and mains flexible power cord.
min. 25
45

Installation
Page 10
Gas Hob User Manual
600mm Hobs - The Gas inlet (1) is located underneath the appliance towards the rear edge. The
Electrical terminal (2) is also located underneath the appliance approximately in the centre of the
rear edge.
2
1
Installation Accessories Supplied
The following installation accessories are supplied with the appliance:
4 x mounting brackets and screws
1 x seal strip
1 x natural gas regulator
4 x ULPG Injectors
IMPORTANT // The gas supply connection point shall be accessible with the appliance installed.

Installation
Gas Hob User Manual
Page 11
Installation Procedure
1. Make the benchtop cut-out for the cooktop
in accordance with the diagrams previously
presented in thismanual.
2. Remove trivets, gas burner capsand
diffusers.
3. Turn thecooktop upside down resting iton
a cloth.
NOTE // Be careful not to damage the ignition
candles and the probes of the flame failure
device during this process.
4. Apply the self-adhesive seal strip onto the
edgesof the cooktop that will be resting on
the benchtop. (Do not overlap the ends of
the sealstrip)
NOTE // Do notuse any jointsealant. The
appliance’s sealingstripensuresa sufficient seal
between the applianceand the benchtop.
5. Feed the flexible power corddown through
the cut-out.
6. Placethe cooktop in the cut-outwithout
securing it.
7. Connect the appliance to the mains
electricity supply (refer to the ‘Electrical
Connection’ section).
8. Connect the appliance to the gassupply
(referto the ‘Gas Connection’ section).
9. Secure the appliance by matching the
screws with the correspondent screw holes
in each bottom corner of thecooktop.
10. Once the gas cooktop has been installed
it is essential to check that neither the
gas pipe nor the electricity cable is in
contact with hot parts of the appliance
or hot gas exhaust.
NOTE // A full operational test and a test
for possible leakages must be carried out
by the installer before leaving. Check all
burner flames are blue in colour, stableand
completely ignite at both high and low flame
settings with no appreciable yellow tipping,
carbon deposition, lifting, floating lighting
back or objectionable odour. Test burners
individually and in combination.
Electrical Connection
IMPORTANT // Electrical connections should
be carried out by a suitably qualified and
competent person in strict accordance with
the wiring rules and national and local safety
regulations.

Installation
Page 12
Gas Hob User Manual
ATTENTION // If the connection cable is
damaged, it must be replaced by a suitably
qualified electrician.
The supply cord has been fitted with a
10A three-pin plug and is designed foruse
with alternating current according to the
indications on the rating label (data plate)
located underneath the cooktop.
Before actual connection make sure that:
•The fuseand electricalsystemcan withstand
theloadrequiredbytheappliance.
•The electrical supply system is equippedwith
an efficient earthhook-upaccordingto the
norms and regulationsprescribed bylaw.
•The plug and switchare easily accessible
after installation.
The wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow - Earth
Blue - Neutral
Brown - Live
As the colours of the wires in the mains lead
of this appliance may not correspond with the
coloured markings identifying the terminals in
your plug, proceed as follows:
•The green and yellow wire must be connected
to the terminal in the plug thatis marked with
theletterE or by the earth symbol or coloured
greenorgreenandyellow.
•Thebluewiremustbe connectedto the
terminalthatis marked withtheletterN or
colouredblack.
•The brown wire must be connected to the
terminalthat is markedwith the letterA or
colouredred.
NOTE // This appliance must be earthed.
Gas Connection
IMPORTANT // Gas connections should be
carriedout by a suitably qualified and competent
person in strictaccordancewith the requirements
of AS 5601 (gas installations) and national and
localregulations.
This gascooktop can be connected with a classB
or D flexible hose, whichcomplies with AS/NZS
1869 and must be certified. The min. inner Ø
must be 10 mm and the maximum length 1.2 m.
Makesure it does not touch movingpartsof the
kitchen furniture, e.g. a drawer.Ensurethe hose
assemblyis not exposed to high temperatures
exceedingthe maximumrecommendedby the
hose manufacturer,subjected to strain, kinking,
permanentdeformationor damagebyvermin.
This appliance is factory fitted with Natural
Gas Injectors and is also supplied with a ULPG
conversion kit. The conversion of the appliance
to be used with ULPG must be undertakenby
qualified personnel. Please refer to the ‘Gas
Conversion –Natural Gas / ULPG’section.
A Pressure Test Point is provided on the gas
regulator. (supplied for natural gas)

Installation
Gas Hob User Manual
Page 13
The Gas pressure must be set by an approved
gas fitter as shown on the table presented
on the next page or,alternatively, on the
appliance data plate:
Natural gas 1.0 kPa
ULPG 2.75 kPa
1. Loosen the screw in the test point until it is
free in its housing. The screw is retained in
this position.
2. Connect the hose from the pressuregauge.
3. Reassemble one of the large burners, turn
on the gas and manually light the burners.
4. Disconnectgauge and screw in thetest
point screw.
NOTE // The Gas Regulator must be set with the
largest burner operating at maximum setting.
Natural Gas ULPG
Gas Pressure Test Point Gas Pressure Test Point
115
95

Installation
Page 14
Gas Hob User Manual
Gas Consumption and Injectors Specifications
TGF64E
Natural Gas
Universal LPG
Inj. diam. (mm)
MJ/h
Gas pressure
Inj. diam. (mm)
MJ/h
Gas pressure
Rapid burner x 1
1.55
12.00
1.0kPa
0.85
10.00
2.75kPa
Semi-rapid burner x 2
1.18
7.00
1.0kPa
0.65
5.50
2.75kPa
Auxiliary burner x 1
0.90
4.00
1.0kPa
0.50
3.30
2.75kPa
Total NHGC
30.00
24.30
TGWF64E
Natural Gas
Universal LPG
Inj. diam. (mm)
MJ/h
Gas pressure
Inj. diam.(mm)
MJ/h
Gas pressure
WOK burner x 1
1.68
12.60
1.0kPa
0.96
12.50
2.75kPa
1.0kPa
2.75kPa
Semi-rapid burner x 1
1.18
7.00
1.0kPa
0.65
5.50
2.75kPa
Auxiliary burner x 1
0.90
4.00
1.0kPa
0.50
3.30
2.75kPa
Total NHGC
30.60 26.80
TGWF93E
Natural Gas
Universal LPG
Inj. diam. (mm)
MJ/h
Gas pressure
Inj. diam. (mm)
MJ/h
Gas pressure
WOK burner x 1
1.68
12.60
1.0kPa
0.96
12.50
2.75kPa
Rapid burner x 1
1.55
12.00
1.0kPa
0.85
10.00
2.75kPa
Semi-rapid burner x 2
1.18
7.00
1.0kPa
0.65
5.50
2.75kPa
Auxiliary burner x 1
0.90
4.00
1.0kPa
0.50
3.30
2.75kPa
Total NHGC
42.60
36.80
NOTE // Thisapplianceis suppliedwitha sparedata plate label. Please attachit toan adjacentsurface for
futurereferenceif the labels on the baseof the cooktopare not visibleafter installation.
Semi-rapid burner x 1 1.18 7.00 0.65 5.50

Installation
Gas Hob User Manual
Page 15
Gas Conversion –Natural Gas / ULPG
This appliance is factory fitted with Natural
Gas Injectors (burner nozzles) and is also
supplied with a ULPG conversionkit. To adapt
the cooktop to a different type of gas, the gas
injectors must be changed as follows:
1. Remove the pan supports (trivets),burner
caps and burnerdiffusers.
2. Unscrew the injectorsusing a 7mm socket
wrench.
3. Replace the injectors with those supplied
corresponding to the gas available (see
burner and injectorcharacteristics table)
IMPORTANT // On completing the operation,
replace the old gas label with the one showing the
newtype of gas;the stickeris availablein the User
Manualpackage
Adjusting the minimum flame
intensity
The minimum flame intensity is adjusted at
the factory. However, when the gas injectors
are replaced or in special mains pressure
conditions, it may be necessary to readjust the
intensity of the minimum flame.
Follow the operationsbelow for each burner in
order to adjust the minimum flame intensities:
1. Light the burner.
2. Turn the knob control anti-clockwise to the
weakest flame.
3. Remove the knob from the valveshaft (and
gasketif there isone).
4. Use a thin blade screwdriver to turn the
bypass screw located on top of the gas
valve shaft.
ULPG
Gently turn the bypass screw clockwiseuntil
it is completelytightened.
Natural Gas
Gently turn the bypass screw clockwise
until it is completely tightened, then slowly
turn it anti-clockwise for adjustment of the
flame. The correct length of the flame is
around 3 to 4mm.
5. Put the knob back on and test if the flame
goes out when quickly turning the knob
control from the strongest flame to the
weakest flame positions.
6. For burners with flame failure device, make
sure that the regulation obtained is sufficient
to maintain the thermocouple activatedwhen
operating with the weakest flame. If it is not,
increase the minimum flame intensity.
NOTE // A full operational test and atest forpossible leakagesmustbe carriedout by the installerbefore
leaving.Check all burner flames are blue in colour,stable andcompletelyignite at bothhigh and low
flame settingswith no appreciableyellowtipping, carbondeposition, lifting,floating lighting backor
objectionableodour.Testburnersindividually andin combination.

CONTACT DETAILS
AUSTRALIA
ARISIT PTY LIMITED
40-50 Mark Anthony Drive
Dandenong South, VIC 3175
Australia
P // 1300 762 219
[email protected]
NEW ZEALAND
ARISIT PTY LIMITED
PO Box 68-140
Newton, Auckland 1145
New Zealand
P // 09 306 1020
F // 09 302 0077
[email protected]
Tisira is committed to ongoing research
and development. Every effort has been
made to ensure all information in this
service manual is correct at time of going
to print. Dimensions should be used as
a reference only and actual dimensions
should be taken from the physical
product only.
Manufacturer reserves the right to
change specifications without notice.