tissin TS400 Series User manual

Limit Switch Box
TS400 Series
Instruction Manual
Tissin Co.,Ltd.
Ver. PM-TS400EN_05/2023

2
Limit Switch Box
TS400 Series
tissin
Table of contents
1 Introduction------------------------------------------------------------------------------------- 3
1.1 General information for the user----------------------------------------------------------- 3
1.2 Limited warranty and disclaimer----------------------------------------------------------- 3
1.3 Requirements for safety--------------------------------------------------------------------- 4
2 Product description---------------------------------------------------------------------- 5
2.1 Function--------------------------------------------------------------------------------------- 5
2.2 Features--------------------------------------------------------------------------------------- 5
2.3 Label-------------------------------------------------------------------------------------------- 5
2.4 Product code--------------------------------------------------------------------------------- 6
2.5 Specification---------------------------------------------------------------------------------- 6
2.6 Structure--------------------------------------------------------------------------------------- 7
2.7 Product dimension-------------------------------------------------------------------------- 8
2.8 Bracket dimension-------------------------------------------------------------------------- 9
3 Installation--------------------------------------------------------------------------------------- 10
3.1 Before installation----------------------------------------------------------------------------- 10
3.2 How to install----------------------------------------------------------------------------------- 10
4 Electrical connection------------------------------------------------------------------- 11
4.1 Mechanical type (2 x SPDT)---------------------------------------------------------------- 11
4.2 Proximity type (Autonics)-------------------------------------------------------------------- 11
4.3 Proximity type (P&F)-------------------------------------------------------------------------- 12
4.4 Mechanical type (2 x DPDT)---------------------------------------------------------------- 12
5 How to adjust cam------------------------------------------------------------------------ 13
5.1 Upper switch------------------------------------------------------------------------------------ 13
5.2 Lower switch------------------------------------------------------------------------------------ 13

3
Limit Switch Box
TS400 Series
tissin
1 Introduction
1.1 General information for the user
This instruction includes installation, operation, maintenance, and parts information for TS400
series. Keep these instructions in a location which is easily accessible to every user and
make these instructions available to every new owner of the device.
Installation, commissioning and maintenance of the product can only be performed by
trained specialist personnel who have been authorized by the plant operator to do so.
To avoid possible injury to the personnel or damage to valve parts, WARNING,
CAUTION and NOTICE must be strictly followed.
Before installing or commissioning, be sure to read and thoroughly understand the
product manual and operate the product properly.
Operators must strictly observe the applicable national regulations with regards to
installation, function tests, repairs, and maintenance of electrical products.
For additional information or if specific problems occur that are not explained in these
instructions, contact the manufacturer.
1.2 Limited warranty and disclaimer
This product has been fully inspected and shipped through a thorough quality inspection
procedure. The manufacturer warranty period of the product is 18 months after the
product is shipped from Tissin in Korea.
For any failure or damage reported within the warranty period which is clearly our
responsibility, a replacement product or necessary parts will be provided. This limited
warranty applies only to our product independently, and not to any other damage
incurred due to the failure of the product.
Using the device in a manner that does not fall within the scope of its intended use,
disregarding this manual, using under unqualified personnel, or making unauthorized
alterations releases the manufacturer from liability for any resulting damage. This
renders the manufacturer's warranty null and void.

4
Limit Switch Box
TS400 Series
tissin
1.3 Requirements for safety
This manual contains notices you have to observe in order to ensure your personal safety,
as well as to prevent damage to property. These safety instructions are intended to prevent
hazardous situations and/or equipment damage. For the safety, it is important to follow the
instructions in the manual.
WARNING
Failure to observe the warning may result in serious injuries or death.
CAUTION
Failure to observe this warning may result in damage to the device or personal injury.
NOTICE
Failure to observe the warning may result in damage to the device or may degrade
performance.
Safety notes
CAUTION
Only trained and authorized person should operate the machinery and the equipment.
If it is out of the specification range, it may cause a malfunction, so please use it in
compliance with the product specification.
Never handle mechanical equipment or disassemble the device until safety is confirmed.
Before reaching into the device or the equipment, please switch off the power supply
and secure to prevent reactivation.
Observe applicable accident prevention and the safety regulations for electrical
equipment.

5
Limit Switch Box
TS400 Series
tissin
2 Product Description
2.1 Function
Limit switch box is a device that notifies the open/closed state of the valve to the central
control room or controller through ON/OFF electrical signals.
2.2 Features
Compact design and External Indicator with good visibility
Easy switch operation position setting with Spring-fixed cam
Can select various switches
IP67 enclosure
NAMUR VDI/VDE 3845, ISO 5211 Bracket standards
2.3Label
Item Description
MODEL Model number
LOT No Serial number
AMBIENT TEMP. Operating temperature
TYPE Type of built-in switch
VOLTAGE Specification of built-in switch

6
Limit Switch Box
TS400 Series
tissin
2.4Product Code
Model TS400
Switch type Mechanical (2xSPDT) M
Proximity P
Mechanical (2xDPDT) D
Conduit entry NPT1/2 1
M20x1.5P 2
G1/2 3
Bracket type None 0
ST-1 (30x80,H20) 1
ST-2 (30x80,H30) 2
ST-3 (30x130,H30) 3
ST-4 (30x130,H50) 4
2.5Specification
Item TS400M TS400P
Switch type
Mechanical (2xSPDT) Proximity
KW3A-16Z3B-A200
(Dongnan)
PSN17-5DNU
(Autonics)
Switch Spec
AC 16A,125/250v -
DC 30V,10A 10~30V
Enclosure IP67
Conduit entry NPT1/2, G(PF)1/2, M20
Ambient temp. -25℃∼70℃(standard)
Terminal 8Points
Material Aluminum die casting
Weight 0.7kg

7
Limit Switch Box
TS400 Series
tissin
2.6Structure

8
Limit Switch Box
TS400 Series
tissin
2.7 Product Dimension

9
Limit Switch Box
TS400 Series
tissin
2.8 Bracket Dimension

10
Limit Switch Box
TS400 Series
tissin
3 Installation
3.1 Before installation
WARNING
Before installation, shut off the air pressure and make sure that no air pressure remains
inside the actuator.
3.2 How to install
①As shown in Figure 02, fasten Bracket to the product with 4pcs-bolts included in the box.
②As shown in Figure 01, mount Limit switch box’s shaft on actuator stem and fasten
Bracket to actuator with bolts.
<Figure 01> <Figure 02>

11
Limit Switch Box
TS400 Series
tissin
4 Electrical connection
WARNING
When open the terminal cover, be sure to turn off the power first.
To protect the product, ground it to the ground terminal inside and outside the product.
4.1 Mechanical type (2 x SPDT)
4.2 Inductive proximity type (Autonics PSN17-DNU, NPN Type)

12
Limit Switch Box
TS400 Series
tissin
4.3 Inductive proximity type (P&F NJ2-V3-N, NC Type)
4.4 Mechanical type (2 x DPDT)

13
Limit Switch Box
TS400 Series
tissin
5 How to adjust cam
5.1 Upper switch
Push the upper cam down, turn left/right to adjust the cam to operate the upper switch in the
desired position, release the cam, and It will return to a stable position by itself.
5.2 Lower switch
Pull the lower cam up, turn left/right to adjust the cam to operate the lower switch in the
desired position, release the cam, and It will return to a stable position by itself.

14
Limit Switch Box
TS400 Series
tissin
Solutions for Control Valve System
Tissin Co.,Ltd.
201-1105, No 397, Seokcheon-ro,Ojeong-gu,
Bucheon-Si,Gyeonggi-do, Korea 14449
Tel : [phone],
Fax : [phone]
www.tissin.co.kr