Korenix JetNet 6710G User manual

1
Korenix JetNet 6710G Series
Industrial 8-Port PoE + 2 Gigabit TX
Managed Ethernet Switch
User Manual
Ver. 05, Jun-2011
Firmware v1.0a
www.korenix.com

2
Korenix JetNet 6710G Series
Industrial 8 Port PoE + 2 Gigabit TX
Managed Ethernet Switch
User’s Manual
Copyright Notice
Copyright ©2010 Korenix Technology Co., Ltd.
All rights reserved.
Reproduction in any form or by any means without permission is prohibited.

3
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his expense.
The user is cautioned that changes and modifications made to the equipment
without approval of the manufacturer could void the user's authority to operate
this equipment.

Index
1 Introduction..........................................................................................................................1
1.1 Overview................................................................................................................. 1
1.2 Major Features ....................................................................................................... 4
1.3 Package List...........................................................................................................5
2 Hardware Installation...........................................................................................................6
2.1 Hardware Introduction............................................................................................ 7
2.2 Wiring Power Inputs............................................................................................... 9
2.3 Wiring RS-232 console and Relay Output............................................................11
2.4 Wiring Earth Ground.............................................................................................12
2.5 Wiring Fast Ethernet Ports...................................................................................13
2.6 Wall-Mounting Installation .................................................................................... 18
3 Preparation for Management.............................................................................................19
3.1 Preparation for Serial Console............................................................................. 19
3.2 Preparation for Web Interface..............................................................................20
3.3 Preparation for Telnet Console............................................................................. 23
4 Feature Configuration........................................................................................................26
4.1 Command Line Interface Introduction..................................................................27
4.2 Basic Setting.........................................................................................................33
4.3 Port Configuration................................................................................................. 53
4.4 Power over Ethernet.............................................................................................61
4.5 Network Redundancy........................................................................................... 70
4.6 VLAN .................................................................................................................... 81
4.7 Traffic Prioritization...............................................................................................91
4.8 Multicast Filtering..................................................................................................97
4.9 SNMP.................................................................................................................102
4.10 Security...............................................................................................................106
4.11 Warning................................................................................................................113
4.13 Monitor and Diag................................................................................................124
4.14 Device Front Panel.............................................................................................132
4.15 Save to Flash......................................................................................................133
4.16 Logout................................................................................................................. 134
5 Appendix..........................................................................................................................135
5.1 Product Specifications........................................................................................135
5.2 Korenix Private MIB............................................................................................140
5.3 Revision History..................................................................................................142
5.4 About Korenix.....................................................................................................143

1
1 Introduction
Welcome to Korenix JetNet 6710G Series Industrial 8-Port PoE + 2G
Managed Ethernet Switch User Manual. Following topics are covered in
this chapter:
1.1 Overview
1.2 Major Features
1.3 Package Checklist
1.1 Overview
The JetNet 6710G series are Managed Industrial Power over Ethernet
Switches, equipped with 8 ports 10/100 TX with 15.4 watts PoE injector and 2
10/100/1000 TX ports for uplink. The 8 ports PSE injector, compliant with IEEE
802.3af/ 802.3at and forced powering feature to supports non-standard
Powered Device (PD). The Gigabit Ethernet ports can be formed as a
redundant ring network or connect with higher level back-bond switch with
MSRTM technologies and provides faster recovery time-less than 5 ms.
Various Network Control and Security Features
The JetNet 6710G provides various network control and security features. The
Network control feature allows user to optimize the industrial network
environment. The supported features include VLAN, IGMP Snooping, Quality
of Service (QoS), Link Aggregation Control Protocol (LACP), Rate Control. The
security also helps users to avoid hacker’s attack. The features included are
DHCP client, DHCP server with IP and MAC binding, 802.1X Access Control,
SSH for Telnet security, IPAccess table and port security.
.Power budget limitation with priority control
The JetNet 6710G provides budget and priority control to ensure the total
power consumption will not over the power budget of power supply user
installed. It also provides budget control function to limit the output power if PD
device is not claimed right consumption numbers. This features allows user to
protect high priority PD device will not be shut down which caused by power
supply over loading protection.
Driving the High Power PoE market - Security, WiMAX
Since the ratification of the Power over Ethernet standard in 2003, the Power

2
over Ethernet technology becomes a trend; more devices adopt PD
technology to obtain power through Ethernet cable. However, the IEEE
802.3af 15.4 w powers can’t satisfy the applications, such like WiMAX, IP DOM
Camera, which require from 15.4w up to 30 watts power. The JetNet 6710G is
equipped with the new PSE solution compliant with both IEEE 802.3af and
IEEE 802.3at 30w high power PoE standards. It supports 8 PoE ports in
End-span wiring architecture with 30w powering ability to drive the motor of
outdoor PZT IP cameras with direction control for cross –street monitoring or
WiMAX systems for internet access at train stations, airports or Hot-spots.
Comprehensive Redundant Solutions – Multiple Super Ring (MSRTM)
The JetNet 6710G supports new generation ring technology - MSRTM (Multiple
Super Ring); the next new generation of RSRTM (Rapid Super Ring) technology.
This new technologies is prefect for different network redundancy applications
and structures. With the MSRTM technology, a node can be configured to
multiple rings with the failover time in as little as 5ms and zero-second of
restore time. In addition, users can extend the ring topology by adding
hundreds of JetNet series to meet the network needs without compromising
the speed of the network. The MSRTM also facilitates the JetNet series to
connect with coe management switch vi standard rapid spanning tree protocol
or through multiple paths or nodes to increase the reliability by RDHTM (Rapid
Dual Homing )(RDHTM )technology. By integrating MSRTM and Link
Aggregation Control Protocol (LACP) the JetNet series can enhance the link
availability and increase to overall link capacity. Two or more Fast Ethernet
connections are bundled in order to increase the bandwidth and to create a
resilient and redundant link
Rapid Super ring (RSRTM) Technology
Rapid Super Ring is the 2nd generation of Korenix Ring Redundancy
technology. The recovery time is greatly improved from 30ms to few ms for
both copper and fiber ring. The Ring master can be auto-selected by RSR
engine. The 1st ring port of the R.M. is the primary path while the 2nd ring port
of the R.M. is the block path. Once the primary path fails, the 2nd path will be
recovered within few ms. Besides, the restore time is also shortened to zero in
the R.M. auto-selection mode.
Seamless Ring Port Restoration TM
Seamless restoration is a new Korenix patented technology which can restore
a failed ring without causing any loop problem, topology change, packet loss
and restoration time. This makes a perfect restoration that will not result in any

3
loop, technology change and restoration time (restoration time = 0 second).
Rapid Dual Homing (RDHTM) Technology
Rapid Dual Homing is also the important feature of Korenix new generation
Ring technology. It supports ring coupling with other vendors and with easy
configuration and multiple redundancies, the failover time is much faster and
the restore time is zero ms. Uplinks can be auto detected and gathered into
groups. In each group, uplinks are sorted into primary, secondary and
standbys by their link speed. The uplink with the highest speed is more likely to
be active path for data transmission. Link aggregation is also integrated into
RDHTM. An uplink connection can be a single link or several links aggregated
as a trunk, which provides better redundancy and link capacity.
TrunkRingTM
TrunkRing is a new feature in MSR which merges the two technologies of RSR
and link aggregation. It takes advantages of aggregation to enhance the link
redundancy, while increase the link speed. The ring will open only if all the
aggregated links are broken. Link aggregation can be achieved by either,
static trunk or LACP. Not all the link sections in a TrunkRing need to be the
same. Ring links can be either symmetric or asymmetric. Some are a single
path, and the others are aggregated by links where the number of links in a
trunk group can be different. Users can enhance the link redundancy at
different locations in accordance to the need. And the link with less speed is
more likely to be used as the backup path for restoring the network to full play
capacity.
Link Aggregation Control Protocol
Link Aggregation Control Protocol allows you grouping multiple Ethernet ports
in parallel to increase the link bandwidth. The aggregated ports can be viewed
as one physical port, so that the bandwidth is higher than just one single
Ethernet port. The member ports of the same trunk group can balance the
loading and backup with each other. The LACP feature is usually used when
you need higher bandwidth for the backbone network. This is a cost-effective
way for you to transfer much more data.
Multi Powering Mechanism- User Manual, Forced and IEEE 802.3at LLDP
Power over Ethernet
Some of Legacy PD devices also feature user defined manual mode and
forced powering mode to support non-standard PD devices without the PoE
signature resistor for some WiMax systems, which are non-compliant with

4
IEEE 802.3at LLDP Power over Ethernet.
For the new PoE standard – IEEE 802.3at, JetNet 6710G implements Link
Layer Discovery Protocol (LLDP) into the system for allowing power budget
negotiation between PD devices while providing smart power budget control
behavior.
Magical Topology Discovery & Management – JetView Pro
JetNet 6710G supports topology discovery or LLDP (IEEE 802.1AB Link Layer
Discovery Protocol) function that can help users to discover multi-vendor’s
network devices on the same segment by an NMS system which supports
LLDP function. With LLDP function, NMS can easily maintain the topology map,
display port ID, port description, system description, VLAN ID and so on. Once
a link failure happens, the topology changed events are updated to the NMS to
help users easily maintain the network system. Like as the JetView Pro, not
only supports topology discovery, it also delivers group IP assignment,
firmware upgrade, configuration files backup/ restore ,SNMP MIB Broswer
/compile, MSRTM group management and also allows user to exports topology
map to drawing file-JPEG, BMP, PNG or PDF for other application.
1.2 Major Features
Korenix JetNet 6710G Series products have the following features:
8 10/100 Base TX and 2 Gigabit ports
Rugged M12 / RJ-45 Ethernet Connector
8 –port IEE 802.3af 15.4w /802.3at 30w Power over Ethernet
Auto Power Budget Control with Thermal Detection
32Gbps switch Fabric, 8K MAC address
Korenix patented MSR pattern aggregates up to 4 x 100M Rings plus 1
Gigabit Ring
LACP/VLAN/ GVRP/ QoS/ IGMP Snooping/Rate Control/ Online Multi-Port
Mirroring/DHCP /IEEE 802.1AB LLDP
Advanced Security system by Port Security, Access IP list, SSH and
HTTPS Login
Event Notification through E-mail, SNMP trap and SysLog
Cisco-Like CLI, Web, SNMP/RMON for network Management
Redundant DC Power Inputs and Relay Output
AC 1.5KV Hi-Pot Protection for power to case, port to case.
Industrial Heat dispersing design,-40~70°C wide operating temperature

5
Note: The detail spec is listed in Appendix 5.1.
1.3 Package List
Korenix JetNet 6710G Series products are shipped with following items
that indicated in the table:
JetNet 6710G-M12
JetNet 6710G-RJ
JetNet 6810G-M12
JetNet 6810G-RJ
JetNet 6710G Managed High Power IEEE 802.3at PoE Switch
(M12 / Rugged RJ) 1 1
JetNet 6810 Managed Booster PoE Switch ( M12 / Rugged RJ)
1 1
M12 on DB9 Shielded Console Cable 1 1 1 1
Rugged M12 D-coded 4-pole Field Assemble able Connecter 8 8
Rugged M12A-coded 8-pole FieldAssemble able Connector 2 2
Rugged RJ45 FieldAssemble able Connecter 10 10
2 Wall-Mount kits & 8 Screws 1 1 1 1
Quick Installation Guide 1 1 1 1
Documentation and Software CD-ROM 1 1 1 1
If any of the above items are missing or damaged, please contact your
local sales representative.

6
2 Hardware Installation
This chapter includes hardware introduction, installation and
configuration information.
Following topics are covered in this chapter:
2.1 Hardware Introduction
Dimension
Panel Layout
Bottom View
2.2 Wiring Power Inputs
2.3 RS-232 console and relay output
2.4 Wiring Earth ground
2.5 Wiring Ethernet Ports
2.6 Wall-mounting Installation

7
2.1 Hardware Introduction
Dimension
JetNet 6710G’s dimension (W x H x D) is 96mm x 137mm x 119mm
JetNet 6710G-m12
JetNet 6710G-RJ

8
Panel Layout
The front panel includes 10/100Mbps PoE ports, Gigabit Ethernet ports,
RS232 console with DO port, System / Port LED and Power input.

9
2.2 Wiring Power Inputs
The Power input port is located at the top of the front panel and supports
redundant input function via a proprietary assembly capable IP-67 connector
(CDG-L207SA) included in the shipment. If you cannot find this power
connector, please contact your local distributor. For the available input power
range and recommended cable size, please refer to the below table.
Power Input (DC Voltage) Input Conductor Cable Size
Minimum Maximum Recommended Redundant Input
AWG No. / CableArea (mm
2
JetNet 6710G-M12 48 60 48 V1, V2 AWG 14 / 2.0
JetNet 6710G-RJ 48 60 48 V1, V2 AWG 14 / 2.0
JetNet 6810G-M12 22 60 24 V1, V2 bind together AWG 14 / 2.0
JetNet 6810G-RJ 22 60 24 V1, V2 bind together AWG 14 / 2.0
Table 2 Power Input Voltage
The JetNet 6810G only supports single power input that binds V1 and V2
together to obtain higher current for the booster.
Use the UL listed Switching power supply to power the JetNet Switch. For
the power wiring method, please refer to the figures 2.2-1 and 2.2-2. For
system safety and the anti-immunity ability, the chassis ground screw should
be well grounded to the earth ground.
Figure 2.2
-
1. Power Supply wiring architecture

10
Figure 2.2
-
2 Power connector assembly diagram

11
2.3 Wiring RS-232 console and Relay Output
The RS-232 console and the alarm relay are connected via the assembly
type of 5-pole M12 A-coding connector included in the supplied package of
JetNet switch. The following figure 3-2-1 is the disassembly diagram of M12
A-coding connector.
In the M12 connector packing, the parts 1, 2, 3 are already assembled.
Follow the steps for soldering and assembling the cable and connector
together:
Step -1: Slide component 4, 5, 6 and then 7 over the
console cable. Keep them loose. Do not tighten them
yet. 2 cable glands are provided for cable diameter from
3.5 to 5.8 mm. Choose the one that best fits the cable.
Picture 8
Step-2: Solder the conductors with the copper wires according to the pin
assignment. The soldering side view of the pin is shown as below:
Fi
g
ure 2.3
-
1 Field Assemble M12 disassembl
y

12
Picture 9 – Console port pin assignment
Step-3: Fasten the components 4, 5, 6 and 7 in sequence. Be sure the
gasket is on the right position. See the below M12 assembly diagram:
Picture 10 – M12 Assembly
.
2.4 Wiring Earth Ground
To ensure the system will not be damaged by noise or any electrical shock,

13
we suggest you to make exact connection with JetNet 6710G with Earth
Ground.
On the left side of JetNet 6710G, there is one earth ground screw. Loosen
the earth ground screw by screw driver; then tighten the screw after earth
ground wire is connected.
2.5 Wiring Fast Ethernet Ports
You can connect terminal devices and other segments via twisted pair cables.
Ports which are not assigned should be closed with the covering caps
contained in the package list of delivery to guarantee the connector is clear
without rust.
Never install or work on/with the equipment or the cabling during the
period of its lightinng activity.

14
Assembly of M12 Ethernet Connector
For Fast Ethernet M12 D-Code to M12 D-Code connection, you can use
either version below:
M12-M12 MDI
1 TX+
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
-
RX+ 1
2 RX+
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
-
TX+ 2
3 TX-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
-
RX- 3
4 RX-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
-
TX- 4
M12-M12 MDI-X
1 TX+
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
-
RX+ 2
2 RX+
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
-
TX+ 1
3 TX-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
-
RX- 4
4 RX-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
-
TX- 3
Picture 14 M12-to-M12 Ethernet Cable Wiring
For Fast Ethernet M12 D-Code to RJ45 connection, the pin assignment of
the patch cable is shown below:
M12-RJ45 MDI
1T X +
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
R X + 3
2R X +
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
T X + 1
3T X -
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
R X - 6
4R X -
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
T X - 2
M12-RJ45 MDI-X
1T X +
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
R X + 1
2R X +
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
T X + 3
3T X -
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
R X - 2
4R X -
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
T X - 6
Picture 15 M12-to-RJ45 Ethernet Cable Wiring

15
For Gigabit Ethernet M12 A-Code to RJ45 connection, the pin assignment of
the patch cable is shown below,
Picture 16 Gigabit M12-to-RJ45 Ethernet Cable Wiring

16
Assembly of Rugged RJ45 Connector (JetNet 6710G-RJ/JetNet
6810G-RJ )
The RJ version provides robust connection by the field assembly capable
rugged RJ45 connector. Each component of the connector is shown below:
3.3.2-1 Rugged RJ45 Connecter Components
Follow the steps to assemble the rugged RJ45 connector:
Picture 18 Rugged RJ45 Cable Connection diagram