Titan 660 Manual

FOOTING DETAIL
660-PF-UG
THE TITAN GALV UPRIGHT W/ PERF BOARD
660-AC-UG
THE TITAN GALV UPRIGHT W/ ACRYLIC BOARD
660-RS-UG
THE TITAN GALV UPRIGHT W/ STEEL BOARD




DATE: DRAWN BY:
5/12/2016
MODEL NUMBER: CHECKED BY:
PRODUCT NAME:
DONL
660 / 770
660 / 770 INSTALLATION
INSTRUCTIONS
WVB
REV:
C
SHEET:
1 OF 5
MODEL 660 / 770
SQUARE POST OUTDOOR BASKETBALL
IMPORTANT NOTICE:
1) EQUIPMENT SHOULD BE CHECKED REGULARLY FOR PROPER
CONNECTING HARDWARE AND STRUCTURAL INTEGRITY. REPLACE ANY
DAMAGED OR MISSING HARDWARE IMMEDIATLY
2) USE OF THIS EQUIPMENT OTHER THAN INTENDED, MAY BE
HAZARDOUS.
3) ALTERATION OR MODIFICATION OF THIS EQUIPMENT MAY BE
HAZARDOUS AND RESULT IN INJURY. FOR REPAIR OR REPLACEMENT,
CONTACT JAYPRO SPORTS
REV DESCRIPTION DATE BY
B BRACE BR45 WAS BRC30 6/15/2010 DRL
C REMOVED E2 FROM DETAIL E 10/25/2011 DRL
48"
8" 36Ø"
56"
RECOMMENDED 3/4" x 42" (4 PLACES)
REBAR TO BE TIED TOGETHER
(TO BE SUPPLIED BY INSTALLER)
8" CONCRETE PAD OR
DOUBLE 8" CONCRETE BLOCKS
10'-0" TOP
OF GOAL TO
PLAYING SURFACE
119 in CENTER OF
TOP MOUNTING HOLE
TO PLAYING SURFACE
9'-1 1/4" REF
TOP PLATE
6'-0"
10" REF
GALVANIZED POLE:
660-AC-UG
660-RS-UUG
660-PF-UG
POWDER COATED BLACK POLE:
770-AC-UG
770-RS-UUG
770-PF-UG

ITEM QTY PART NUMBER DESCRIPTION
1 1 666U UPRIGHT
2 1 666R 666 OUTRIGGER
3 1 VARIOUS BACKBOARD PER ORDER
4 1 666-1A 666 MOUNTING PLATE
5 2 SR5370 850RB-BB MOUNTING TAB
6 2 660-BR 1.315 DIA BACKBOARD BRACE
7 1 EC0061 6" x 6" PLASTIC END CAP
8 1 UBG-500 ULTIMATE PLAYGROUND BASKETBALL GOAL
9 1 JNY-6HP BRAIDED NYLON BASKETBALL NET 1/2 PR
ITEM QTY PART NUMBER DESCRIPTION
10 2 HB5031 3/8-16 x 1-1/2 CARRIAGE BOLT-ZP
11 6 HS5061 3/4-10 x 8 HEX CAP SCREW-ZP-Gr5
12 3 HS287 3/8-16 x 1-1/4 HEX CAP SCREW-ZP-GrNC
13 12 HW343 3/4 SAE WASHER-ZP-GrNC
14 5 HW334 3/8 LOCK WASHER-ZP-GrNC
15 7 HW2050 3/8 STD WASHER-ZP-GrNC
16 5 HN264 3/8 - 16 Hex Nut - ZP - GrNC
17 2 HN5040 3/8"-16 SLAB BASE TEE NUT, SS
18 6 HN5019 3/4-10 STOVER LOCKNUT ZINC PLATE
2 OF 5
PAGE
MODEL 660/770 SQUARE POST OUTDOOR BASKETBALL
ASSEMBLY INSTRUCTIONS
BEFORE YOU START
A) UNPACK ALL PARTS AND CHECK AGAINST PARTS LIST TO ENSURE THAT ALL PARTS HAVE BEEN INCLUDED
B) INSPECT FOR DAMAGE. REPORT ALL DAMAGES TO TRUCKING COMPANY.
UPRIGHT INSTALLATION
1) CHECK LOCAL BUILDING CODES BEFORE STARTING THE FOOTING, AS BUILDING CODES MAY VARY. LOCAL
BUILDING CODES SHOULD BE ADHEARED TO IF REQUIRENENTS ARE GREATER THAN THOSE OUTLINED HERE.
2) DIG HOLE 36 INCHES SQUARE OR ROUND TO A DEPTH ON 56 INCHES, POUR AN 8 INCH FOOTING AND
ALLOW TO FULLY CURE OR PLACE UPRIGHT ON TWO 8 INCH CONCRETE BLOCKS.
3) INSTALL SQUARE CAP TO TOP OF POST WITH RUBBER MALLET. (BEFORE RAISING ONTO FOOTING)
4) POSITION AND SQUARE THE UPRIGHT ONTO THE FOOTING BASE. POUR THE REMAINDER OF THE FOOTING.
ALLOW THE CONCRETE TO FULLY CURE, PER THE MANUFACTURER'S INSTRUCTIONS, BEFORE ATTACHING
OUTRIGGER AND BACKBOARD.
FINAL ASSEMBLY
5) ATTACH OUTRIGGER TO UPRIGHT USING 3/4"-10 HARDWARE PROVIDED (SEE DETAIL A). IF NEEDED, THE
OUTRIGGER MAY BE LEVELED BY PLACING ALUMINUM FLASHING BEHIND THE MOUNTING PLATE LOCATED
TOWARDS THE BOTTOM.
NOTE THE TOP HOLE OF THE BACKPOARD MOUNTING PLATE SHOULD BE 119 INCHES OFF THE PLAYING
SURFACE.
6)ATTACH THE APPROPRIATE BRACE MOUNTING BRACKET TO THE BACK OF THE BACKBOARD, AS SHOWN IN
DETAIL E. THE BRACKET WILL DEPEND ON THE BACKBOARD ORDERED. THE BRACKETS WILL EITHER BE
INCLUDED WITH THE BACKBOARD OR FOUND IN THE GENERAL KIT. THE SPACING BETWEEN THE RIGHT
ANGLE BRACKETS OF THE RECTANGULAR STEEL BACKBOARD IS APPROXMATLY 36 INCHES.
7) LIFT AND ATTACH THE BACKBOARD TO THE OUTRIGGER USING ONLY THE TOP TWO FASTENERS AND TEE
NUTS SHOWN IN SECTION B-B. WHEN THE BACKBOARD IS INSTALLED THE TEE NUTS SHOULD BE UP AGAINST
THE BACKBOARD AS SHOWN IN SEE DETAIL C. THE USE OF THE TEE NUTS ALLOW FOR EASY REPLACEMENT
OF THE GOAL.
8) INSTALL THE 1 5/16" DIA SUPPORT BRACES TO THE BACKBOARD AND OUTRIGGER AS SHOWN IN DETAILS F
AND G. PLUMB AND LEVEL THE BACKBOARD BEFORE TIGHTENING THE HARDWARE.
9)FINALLY ATTACH THE GOAL WITH THE REMAINING HARDWARE SHOWN IN SECTION B-B,MAKE CERTAIN
THAT A WASHER IS PLACED BETWEEN THE BOARD AND THE GOAL IN THE LOWER TWO HOLES IN ORDER TO
KEEP THE GOAL PERPENDICULAR WITH THE BACKBOARD. NOTE THE ORIENTATION OF THE LOWER TWO
BOLTS. FOR ADDED SAFETY, THE EXPOSED THREADS AND NUTS SHOULD BE PLACED ON THE BACKSIDE OF
THE BACKBOARD, AS SHOWN IN DETAIL D.
TOOLS REQUIRED:
1 1/8" Socket Wrench and Combination Wrench
9/16" Socket Wrench and Combination Wrench
Rubber Mallet

DETAIL A
MOUNTING OUTRIGGER TO UPRIGHT 3 OF 5
PAGE
MODEL 660/770
SQUARE POST OUTDOOR UPRIGHT
3/4-10 STOVER LOCKNUT ZINC PLATE
3/4 SAE WASHER-ZP-GrNC
10" HIGH x 9-1/4" WIDE MOUNTING PLATE
3/4 SAE WASHER-ZP-GrNC
3/4-10 x 8 HEX CAP SCREW-ZP-Gr5
6" x 6" PLASTIC END CAP
OUTRIGGER
1
0
"
UPRIGHT
9'
-
1
1/
4
"

DETAIL W
SCALE 0.04 : 1
E1
4 OF 5
PAGE
E1
RECTANGULAR STEEL BOARD
E2
PERFORATED BOARD OR ACRYLIC BOARD
(BRACKET & HARDWARE PROVIDED W/BOARD)
BRACE TO BOARD MOUNTING OPTIONS
DETAIL F
UPPER BRACE ATTACHMENT
DETAIL E
M10 x 60mm BOLT, SS
M10 NYLOCK NUT, SS
M10 WASHER, SS
NOTE ARROW
ORIENTATION
PERFORATED & ACRYLIC BOARD
RECTANGULAR STEEL BOARD
3/8 STD WASHER-ZP-GrNC
3/8 LOCK WASHER-ZP-GrNC
3/8 - 16 Hex Nut - ZP - GrNC
850RB-BB MOUNTING TAB
3/8-16 x 1-1/2 CARRIAGE BOLT-ZP
3/8 - 16 Hex Nut - ZP - GrNC
3/8 LOCK WASHER-ZP-GrNC
3/8 STD WASHER-ZP-GrNC
1.315 DIA BACKBOARD BRACE
3/8-16 x 1-1/4 HEX CAP SCREW-ZP-GrNC

Y
Y
5 OF 5
PAGE
ALL THE HARDWARE IN THIS DETAIL EXCEPT FOR
THE TEE NUTS IS SUPPLIED WITH THE GOAL
UBG-500
3/8-16 x 3-1/2 HEX CAP SCREW-ZP-GrNC
3/8 SAE WASHER-ZP-GrNC
3/8 STD WASHER-ZP-GrNC
3/8 SAE WASHER-ZP-GrNC
BACKBOARD
BACKBOARD MTG PLATE
3/8" MEDIUM SPLIT LOCK WASHER, ZP
3/8"-16 FINISH HEX NUT, ZP
3/8"-16 FINISH HEX NUT, ZP
3/8" MEDIUM SPLIT LOCK WASHER, ZP
3/8 SAE WASHER-ZP-GrNC
3/8"-16 SLAB BASE TEE NUT, SS
3/8 SAE WASHER-ZP-GrNC
3/8-16 x 3-1/2 HEX CAP SCREW-ZP-GrNC
DETAIL G
BRACES TO OUTRIGGER ATTACHMENT
1.315 DIA BACKBOARD BRACE
1.315 DIA BACKBOARD BRACE
OUTRIGGER BRACE TAB
3/8 STD WASHER-ZP-GrNC
3/8 LOCK WASHER-ZP-GrNC
3/8 - 16 Hex Nut - ZP - GrNC
3/8-16 x 1-1/4 HEX CAP SCREW-ZP-GrNC
OUTRIGGER
BOARD
UBG-500
3/8" WASHERS PLACED BETWEEN
THE GOAL & THE BACKBOARD
3/8" TEE NUTS PLACED BETWEEN
THE GOAL & THE BACKBOARD
SECTION B-B
DETAIL C/D