Titus TAO User manual

Redefine your comfort zone. ™ | www.titus-hvac.com
TEMPERATURE AMBIENT OPTIMIZER
INSTALLATION &
OPERATION MANUAL
TEMPERATURE AMBIENT OPTIMIZER
TAO

2IOM - TAO Redefine your comfort zone. ™ | www.titus-hvac.com
IOM TAO
Receiving Inspection
TAO Installation
After unpacking the unit, check it for shipping damage. If any shipping
damage is found, report it immediately to the delivering carrier. Store units
in a clean, dry location prior to installation.
STEP 1:
Remove the front mounting base panel by unscrewing it from the mounting
base as shown in Figure 1.
STEP 2:
Uninstall the front cover by taking off the décor strip with the help of flat
head screw driver and unscrewing six screws as shown in Figure 2.
TEMPERA
TURE AMBIENT OPTIMIZ
ER
TAO

3
IOM - TAO
Redefine your comfort zone. ™ | www.titus-hvac.com
TAO Installation
STEP 3:
Remove the front cover with the help of two screw drivers by lifting up and
pulling out as shown in Figure 3 to have access to the inside of the unit.
STEP 4:
Unscrew the front accent panels. See Figure 4.
STEP 5:
Mount the floor angle to the floor 6 ¾” away from the wall with the help
of anchor screws (not included). See Figure 5.

4IOM - TAO Redefine your comfort zone. ™ | www.titus-hvac.com
IOM TAO
TAO Installation (continued)
STEP 6:
Slide the unit against the wall. Use the slots of the mounting base to drill
hole into the floor angle. Screw the unit mounting base to the floor angle
to secure the bottom end of the unit as shown in Figure 6.
STEP 7:
To secure the top of the unit to the wall place fasteners (not included)
into the drywall as per the dimensions provided in Figure 7. Screw the
unit to the wall with drywall screw (not included) in four places as shown
in Figure 7.
TEMPERA
TURE AMBIENT OPTIMIZ
ER
TAO

5
IOM - TAO
Redefine your comfort zone. ™ | www.titus-hvac.com
TAO Installation (continued)
STEP 8:
To remove side accent panel for duct connections unscrew the panel in
five places from the outer side panel as shown in Figure 8.
STEP 9:
To access the duct work and piping connections remove outer side panels
by unscrewing three screws each from Top and Bottom plate as shown
in Figure 9. Also unscrew two screws from Top and Bottom brackets from
front as shown in Figure 9.
To remove the drain pan for cleaning purpose unscrew the center support
in six places as shown in Figure 9 and slide the drain pan out.

6IOM - TAO Redefine your comfort zone. ™ | www.titus-hvac.com
IOM TAO
TAO Installation (continued)
Primary Airflow Commissioning
STEP 10:
To connect oval trunk of two units in series use oval coupling
(option) as shown in Figure 10 and seal it with duct sealant to
avoid leakage.
For commissioning remove the left front cover as shown in Figure 2 and Figure 3. Take off the pipe cap and use the commissioning tube to obtain the
internal pressure of the plenum as shown in Fig 11. The K-factor of the unit is stated on K-factor label mounted on left inner side panel on top of the
commissioning tube mount. The K-factor can also be found on our website in the relevant K-factor guide.
Figure 11
UNIT SIZE/CONFIGURATION K – FACTOR
5 FOOT WITH Ø6” ROUND INLET 194.9
5 FOOT WITH 8” OVAL INLET 203.4
6 FOOT WITH Ø6” ROUND INLET 247.6
6 FOOT WITH 8” OVAL INLET 258.0
TEMPERA
TURE AMBIENT OPTIMIZ
ER
TAO

7
IOM - TAO
Redefine your comfort zone. ™ | www.titus-hvac.com
Notes

605 Shiloh Rd
Plano TX 75074
ofc: 972.212.4800
fax: [phone]
Redefine your comfort zone. ™ | www.titus-hvac.com
TEMPERA
TURE AMBIENT OPTIMIZ
ER
TAO