TMI Products VJ5 Series Quick start guide

ANALOGUE QUARTZ
TECHNICAL GUIDE
&
PARTS CATALOGUE
Cal.VJ5 Series
(VJ52B/53B/55B)
31032022

Version-01
Cal.VJ5 Series
(VJ52B/53B/55B)
φ28.60 mm
25.70 mm ：between 12 o'clock and 6 o'clock sides
25.70 mm ：between 3 o'clock and 9 o'clock sides
φ27.80 mm
25.70 mm ：between 12 o'clock and 6 o'clock sides
24.10 mm ：between 3 o'clock and 9 o'clock sides
SPECIFICATION
Movement
size
1
Movement
Casing diameter
Total height
3 Hands Calendar
3 Hands Day & Wide
Date Calendar
Time indication
3 Hands Day &
Date Calendar
Electronic circuit
reset switch
Second setting device
Date setting
Driving system
Less than ± 20 seconds at normal temperature range
32,768 Hz
Step motor （Load compensated driving pulse system type）
Loss/Gain (Monthly rate)
Frequency of crystal oscillator
Antimagnetic
≧1600 A/m
Additional mechanism
Electronic circuit reset switch
Second setting device
Date setting
Day setting
Cal. No.
Item
2.71 mm
(including the battery)
2.94 mm
(including the battery)
2.94 mm
(including the battery)
VJ52B
VJ53B
VJ55B
Outside diameter
Jewels
0 Jewel
- 5 ℃～+ 50 ℃
Regulation system
Nil
Operational temperature range
Battery
SR621SW (Silver oxide battery)
Battery life is approximately 3 years
Measuring gate by quartz tester
Use 10 second gate
* Set the winding stem with crown at the normal position

Version-02
Cal.VJ5 Series
(VJ52B/53B/55B)
Lubricating : Types of oil
Disassembling procedures Figs.
① → ㉝
A3a / Moebius 9010
A2a / Moebius 9030
Reassembling procedures Figs. ㉝
→ ①
Oil quantity
Normal quantity
Hour, minute and second hands
Dial
0808 044
Date dial guard
*Date dial
0810 890
Date jumper
0273 021
Hour wheel
0802 030
Date driving wheel
*Refer to page 6 for each parts code
⑦
PARTS CATALOGUE
2
<<VJ52B>>
②
③
④
⑤
①
⑥

Version-02
Cal.VJ5 Series
(VJ52B/53B/55B)
Lubricating : Types of oil
Disassembling procedures Figs.
① → ㉝
A3a / Moebius 9010
A2a / Moebius 9030
Reassembling procedures Figs. ㉝
→ ①
Oil quantity
Normal quantity
Hour, minute and second hands
Dial
0963 230
Snap for day star with dial disk
*Day star with dial disk
0989 011
Intermediate wheel for day corrector
0808 175
Date dial guard
*Date dial
0962 033
Second intermediate wheel
for calendar corrector 0737 012
Day-date corrector wheel
0273 017 0810 890
Hour wheel Date jumper
0802 031
Date driving wheel
*Refer to page 6 for each parts code
3
PARTS CATALOGUE
<<VJ53B>>
①
⑦
②
⑩
⑨
⑪
⑫
③
④
⑤
⑥
⑧

Version-02
Cal.VJ5 Series
(VJ52B/53B/55B)
Lubricating : Types of oil
Disassembling procedures Figs.
① → ㉝
A3a / Moebius 9010
A2a / Moebius 9030
Reassembling procedures Figs. ㉝
→ ①
Oil quantity
Normal quantity
Hour, minute and second hands
Dial
0963 230
Snap for day star with dial disk
*Day star with dial disk
0989 011
Intermediate wheel for day corrector
⑥0808 175
Date dial guard
*Date dial
0962 033
Second intermediate wheel
for calendar corrector ⑧0737 012
Day-date corrector wheel
0273 017 ⑩0810 890
Hour wheel Date jumper
0802 031
Date driving wheel
*Refer to page 6 for each parts code
⑫
4
⑤
⑦
⑨
⑪
④
①
PARTS CATALOGUE
<<VJ55B>>
②
③

Version-02
Cal.VJ5 Series
(VJ52B/53B/55B)
Lubricating : Types of oil
Disassembling procedures Figs.
① → ㉝
A3a / Moebius 9010
A2a / Moebius 9030
Reassembling procedures Figs. ㉝
→ ①
Oil quantity
Normal quantity
Battery 4004 303
Circuit block with coil block
0351 001
Winding stem
0016 121
Screw for battery
* Fourth wheel and
connection (+) pinion
* Battery connection (+) 0231 066
0701 170 Third wheel and pinion
Fifth wheel and
pinion 0033 219
Reset pin
4146 126
Step rotor
*Refer to page 6 for
4216 088 each parts code
Insulator 4239 062 ㉘0391 041
Rotor stator
Train wheel setting
lever
4270 385
Battery connection (-) ㉙0033 220
Pin for setting wheel
0281 041
Setting wheel ㉛0261 291
Minute wheel and
pinion
*Center wheel and
pinion ㉜0282 089
Clutch wheel
0125 297
Train wheel bridge
*1 Oiling position *2 Oiling position
*Refer to page 6 for each parts code
⑲
5
PARTS CATALOGUE
⑬
⑭
⑳
㉑
㉒
㉓
㉔
㉕
㉖
㉗
㉝
⑮
⑯
⑰
⑱
㉚
*1
*2

Version-01
Cal.VJ5 Series
(VJ52B/53B/55B)
Remarks:
O Date dial
<VJ52B>
<VJ53B>
<VJ55B>
O Day star with dial disk
<VJ53B>
<VJ55B>
O Different parts for each CAL.
O The part which is not common in Cal.VJ52B/VJ53B/VJ55B
*All parts code are subject to change without notice.
Language
3H
12H
White
English
Monolingual
Black
White
Positing of
crown
Positing of
date frame
Color of figure
Color of
background
Part code
0878 415
Part code
0150 290
Positing of
crown
3H
0150 280
Part code
Fourth wheel and pinion
0144 105
0144 125
0144 125
㉑
Parts name
VJ52B
VJ53B
VJ55B
Battery connection(+)
⑯
4268 060
4268 061
4268 062
－
0962 009
0962 009
0221 065
0221 066
0221 066
First intermediate wheel for calendar
corrector
㉗
Center wheel and pinion
㉝
3H
3H
0806 142
－
－
Parts name
VJ52B
VJ53B
VJ55B
Date corrector wheel
White
0878 285
3H
3H
Black
White
0878 455
3H
3H
Black
White
0878 435
3H
3H
Black
3H
Black
Color of
background
Language
English &
Spanish
White
White
Positing of
date frame
Color of figure
MON～SAT:Black
SUN :Red
Positing of
date frame
Color of figure
Color of
background
6H
Black
6
Color of
background
PARTS CATALOGUE
Part code
Positing of
crown
Positing of
date frame
Color of figure
Color of
background
Part code
Positing of
crown
Positing of
date frame
Color of figure
Positing of
crown
0878 475
3H

Version-01
Cal.VJ5 Series
(VJ52B/53B/55B)
The explanation here is only for the particular points of Cal.VJ52B /VJ53B/ VJ55B
Ⅰ.STRUCTURE OF THE CIRCUIT BLOCK
Notes: Since the circuit block and coil block are made by one piece, in disassembling and
reassembling take care not to cut the coil line.
Crystal unit
Input terminal(+)
C-MOS-IC
Coil block
Input terminal(-)
Ⅱ. REMARKS ON DISASSEMBLING AND REASSEMBLING
①Hands
・How to install
Place the movement directly on a flat metal plate or the like
to install the hands.
②Intermediate wheel for day corrector
Set the intermediate wheel for day corrector in the
direction as shown in the illustration at right.
*Cal.VJ52B not Intermediate wheel for day corrector.
③Date dial guard
The date dial guard has three protrusions to be caught under the main plate, and it is also fixed
by two guide pins.
・How to remove
Lightly lift the A portion of the date dial guard with
tweezers to release it from the guide pin, and then
move it in the clockwise direction until it gets off
the guide pin.
Release the B portion of the date dial guard in the
same way as described above, and then move it in
the clockwise direction until gets off the guide pin.
Check that all the three protrusions of the date dial
guard have come off from the main plate, and then
remove the date dial guard.
TECHNICAL GUIDE
7
Main plate side
Dial side
1)
2)
3)
Metal plate
B portion
Protrusion
A portion
Date dial guard
Guide pin
Tweezers
UP

Version-01
Cal.VJ5 Series
(VJ52B/53B/55B)
・How to install
Put the date dial guard on the main plate so that
the A and B portion are over the guide pins,
as shown in the illustration at right.
Move the protrusion D of the date dial guard in the
counterclockwise direction so that it is caught
under the main plate.
Slightly move the protrusions C and E in the
counterclockwise direction alternately to set
them under the main plate. Then, set the
A and B portions of the date dial guard to
the guide pins.
Check that the date dial guard is fixed
securely to the main plate.
④Battery
・How to install battery
Insert the battery aslant in the direction shown by the arrow.
Check the battery connection (+) securely touches the side
face of the battery.
Correct
Battery Main plate
⑤Battery connection (+)
・How to install
Have the hook portions (3 places) catch the main plate (Fig.1 & Fig.2).
In disassembling and reassembling, take care not to deform the hook portion.
After installing the battery connection (+), check that the three hook portions securely catch the main plate.
Hook position
Tweezers
Main plate
Hook portion
TECHNICAL GUIDE
8
1)
2)
3)
4)
[Fig.1]
[Fig.2]
Protrusion C
B portion
Protrusion D
Protrusion E
A portion
Battery connection (+)
Coil block
Hook position

Version-01
Cal.VJ5 Series
(VJ52B/53B/55B)
⑥Insulator
・Setting position
Notes: To Insulate between the battery connection (+) and the battery connection (-),
Insulator should be put at the three pin securely as bellow.
Pin
Insulator
⑦Train wheel bridge
・Setting position
Notes: Since the fifth wheel and pinion and step rotor are made of plastics, take care not to damage
them in disassembling and reassembling.
Fourth wheel and pinion
Pin for setting wheel Fifth wheel and pinion
Minute wheel and pinion Setting wheel Setting wheel
Step rotor
Third wheel and pinion
Third wheel and pinion Minute wheel and pinion
Reset pin
Step rotor
Fifth wheel and pinion Center wheel and pinion
Fourth wheel and pinion Clutch wheel
⑧
Train wheel setting lever
・Setting position
Notes:
・Catch the part of spring of the Train wheel setting lever to the pin like as below.
・Take care not to deform the spring potion of the Train wheel setting lever.
Train wheel setting lever
TECHNICAL GUIDE
9
Clutch wheel

Version-01
Cal.VJ5 Series
(VJ52B/53B/55B)
⑨
Pin for setting wheel
Notes:
・In disassembling and reassembling, take care not to damage the portion that is assembled of the pin.
(Since the portion that is assembled of the pin is made of plastics and easily damaged.)
・In disassembling,
pick the pin up main plate to vertical direction with care.
Pin for setting wheel
Center wheel and pinion
Minute wheel and pinion
・In reassembling,
push the pin in main plate to vertical direction with care.
Pin for setting wheel
Setting wheel Main plate
Minute wheel and pinion Center wheel and pinion
10
TECHNICAL GUIDE
(The portion that is assembled
of the pin)
Tweezers