TOKISTAR LIGHTING Micro Tracklight Series User manual

Micro Tracklight Series 24 VDC
TOKISTAR LIGHTING
INSTRUCTION MANUAL
TOKISTAR®LIGHTING
1015 E. Discovery Lane
Anaheim, CA 92801
TEL: [phone] FAX: [phone]
email: [e-mail] Website: tokistar.com
PRECAUTIONS
1. Read all instructions completely before beginning installation.
2. Turn off electricity before beginning installation.
3. All wiring is to be performed by a qualied electrician.
4. Installation must comply with the National Electrical Code, and all applicable codes.
5. Turn main supply to the Power Supply on only after all connections have been made and tested.
6. Use only LED Drivers provided by Tokistar with the system.
General Description
Tokistar’s Micro Tracklight Series operates at 24 VDC from
Class 2 Power Supplies. LED Modules with pivoting heads can
be positioned at any location on the track. Each LED module
consumes 1.6 watts. Each xture is labeled with load and oper-
ating voltage.
Version 1.2
Step 1: Measure and cut the track to size.
Step 2: Determine position of LED Modules on track.
LED Modules can be removed
and repositioned on the track
by pressing buttons on the sides.
Firmly re-insert modules in
the track.
LED Module contact direction
Right Wrong
contact
Contacts must face in the
direction of the feed connector.
Feed Connector
Tabs
LED Module
Track Tabs must securely snap in
place under lip of Track.
Tabs
Button
Inserting LED Modules
Pivoting Head
LED Module Track
Spacer
Button

Micro Tracklight Installation Instructions Page 2
Mounting Clamp
Mounting clamps are attached
with screws and the Micro
Tracklight xture is snapped in
place. Recommended spacing is
every 12".
Retainer Clips
Retainer clips are included with Feed
Connectors and Flex Connectors.
These snap onto the xture to provide
a secure connection.
Feed Connector Assembled
Feed Connector
Feed Connectors bring power to one end of a Tracklight run. Up
to 60 LED Modules can be powered from a single connector.
Mounting Clamp
Retainer Clips snap in
place from above.
Flex Connector
Assembled
Step 3: Insert Feed Connector and End Cap
Step 5: Cut Spacer to size and insert between
LED Modules.
Spacer
Step 3A: Insert Flex Connector
(if required)
Step 6: Install mounting clamps
Do Not Snap Connectors in place
from above. Slide in place.
Retainer
Clips
Retainer Clips
Step 4: Attach Retainer Clips
Do Not Snap End Caps in place
from above. Slide in place.
Lens Replacement
Snoot
Remove Snoot
To replace a lens: Remove the Snoot then gently tap the LED module on a
hard surface and the lens will pop out. Insert new lens and re-insert Snoot.
Remove Lens Insert New Lens
Re-insert Snoot

Micro Tracklight Installation Instructions Page 3
LED Driver Installation
LDR24-16 (16 Watts) / LDR24-25 (25 Watts) / LDR24-40 (40 Watts)
These Class 2 LED Drivers convert an AC input into a 24 VDC output. Refer to the manual provided with
the LED Driver for detailed installation instructions.
Part# Input Volts Output Volts Output Ratings Capacity
LDR24-96 100~240 24 VDC 1 @ 4.0 Amps 60 LED Modules
LDR24-192
Tokistar’s LDR24-192 has two independent 96 watt outputs. This unit has wiring compartments for splicing on
input and output leads, and can be connected directly to conduit. Refer to the manual provided with the LED
Driver for detailed installation instructions.
Part# Input Volts Output Volts Output Ratings Capacity
LDR24-192 100~277 24 VDC 2 @ 4.0 Amps 120 LED Modules
Part# Input Volts Output Volts Output Ratings Capacity
LDR24-16
LDR24-25
LDR24-40
100~240
100~240
100~240
24 VDC
24 VDC
24 VDC
1 @ 0.67 Amps
1 @ 1.05 Amp
1 @ 1.67 Amps
10 LED Modules
15 LED Modules
25 LED Modules
LDR24-96
This 96 Watt Class 2 LED Driver converts an AC input into a 24 VDC output. Refer to the manual provided
with the LED Driver for detailed installation instructions.
24 VDC Output
Black Wire: -V
Red Wire: +V
100~240 VAC Input
Brown Wire: AC Line
Blue Wire: AC Neutral
LDR24-16 / LDR24-25 / LDR24-40 LED Drivers
LDR24-96 LED Driver
100~240 VAC Input
Brown Wire: AC Line
Blue Wire: AC Neutral
Yellow/Green Wire: Ground
24 VDC Output
Black Wire: -V
Red Wire: +V
24 VDC Output
Black Wire: -V
Red Wire: +V
Black Wire: -V
Red Wire: +V
100~277 VAC Input
Yellow/Green Wire: Ground
Black: AC Line
White: AC Neutral
LDR24-192 LED Driver
24 VDC LED Drivers
Micro Tracklight is ETL Listed when operated from our selection of 24 VDC LED Drivers. These Class 2
power supplies range from 16 to 192 watts. The input is universal ranging from 100 to 277 VAC 50/60 Hz.
100~277 VAC Input (North America Only)
100~277 VAC Input (North America Only)

Secondary Circuit Wiring
Secondary Circuit Limit
Do Not Exceed LED Driver Capacity / Maximum 96 watts
Micro Tracklight Installation Instructions Page 4
24 VDC Output
Black Wire: -V
Red Wire: +V
Black Wire: -V
Red Wire: +V
100~277 VAC Input
Yellow/Green Wire: Ground
Black Wire: AC Line
White Wire: AC Neutral
LDR24-192 LED Driver
Micro Tracklight
Micro Tracklight
Yellow Wire: -V
Black Wire: -V
Red Wire: +V
Yellow Wire: -V
Black Wire: -V
Red Wire: +V
Non-Dimming Wiring Details
Single Output LED Driver
Dual Output LED Driver
Micro Tracklight
Yellow Wire: -V
Black Wire: -V
Red Wire: +V
24 VDC Output
Black Wire: -V
Red Wire: +V
100~240 VAC Input
Brown: AC Line
Blue: AC Neutral
Yellow/Green Wire: Ground
LDR24-96 LED Driver

Micro Tracklight Installation Instructions Page 5
LC-1CH-MULTI Dimming System
Dimmer Pack - Part #: LC-1CH-MULTI
Each dimmer pack receives 24 VDC from an LED Driver. The LDR24-192 LED Driver has two independent 96 watt
outputs. Each output requires an independent dimmer pack.
DMX Mode - Each unit is independently addressable. Up to 36 dimmer packs may be connected in series. For
applications exceeding 36 dimmer packs, an additional feed from the DMX dimmer is required. The additional feed(s)
can be sent directly from the dimmer, or you may use DMX Splitters. Consult factory on details of DMX Splitters.
Analog Modes - For operation from devices using 0/1-10 VDC protocol, up to 10 dimmer packs may be connected in
series. For applications exceeding 10 dimmer packs, an additional feed from the analog dimming device is required.
Manual Mode - You may select a light intensity the xtures will operate at. In this case, no external dimming device
is required.
For further information, refer to the instruction manual provided with the LC-1CH-MULTI Dimmer Pack.
Dimming Micro Tracklight
0/1-10 VDC In
DMX In
LED Driver
Micro Tracklight
24 VDC Output
Yellow Wire: PWM Signal
Red Wire: +V
0/1-10 VDC to next Dimmer Pack
DMX next Dimmer Pack
100~240 VAC Input
Dimmer
Pack
24 VDC Input
Black Wire: -V
Red Wire: +V
Black Wire: -V

LC Dimming System
Wall Dimmer - Part #: LC-DMR
Power to the remote wall dimmer is provided from the LED Driver powering the rst Dimmer Pack. A 50 foot
CAT5 cable is provided.
Dimmer Pack - Part #: LC-1CH-DP
Each dimmer pack receives 24 VDC from an LED Driver. The LDR24-192 LED Driver has two independent
96 watt outputs. Each output requires an independent dimmer pack.A CAT5 cable is provided with each unit.
Up to 25 dimmer packs may be connected in series if the total length of all CAT5 cable does not exceed 165 feet
from the wall dimmer to the last dimmer pack.
For further information, refer to the instruction manual provided with the LC-1CH-DP.
Micro Tracklight Installation Instructions Page 6
TOKISTAR®LIGHTING
1015 E. Discovery Lane
Anaheim, CA 92801
TEL: [phone] FAX: [phone]
email: [e-mail] Website: tokistar.com Version 1.2
Dimming Micro Tracklight
Micro Tracklight
Black Wire: -V
Dimmer
Pack
24 VDC Output
Yellow Wire: PWM Signal
Red Wire: +V
24 VDC Input
Black Wire: -V
Red Wire: +V
-V +V
LC-DMR
Dimmer Signal to next Dimmer Pack
100~240 VAC Input
LED Driver