Tomofree A11 User manual
tomofree.com
Video Instrucions on YouTube
Search:Tomofree
After Sales Support:
support@tomofree.com
A11 User Manual
We strongly recommend that you read this entire
manual before using your electric scooter
How to start
Dashboard
Error Code
1
2
3
4
5
6
7
8
9
13
14
17
18
19
1
2
3. Install the handlebar, tight it with screw.
1. Take the scooter out of the box carefully. 2. Open the buckle, push down sleeve, lock the
buckle.
4. Connect the wire plugs, plugs need color to color.
3
1
2
How to start
Turn on: one short click on the power switch to open the scooter.
Turn off: 3 seconds long press to turn scooter off.
Change speed mode: open the scooter first, then 2 short click to change speed mode.
Change start mode: open the scooter first, then 4 short clicks to change zero/ no-zero speed start mode.
Change KM/H to MPH: open the scooter, then 6 clicks to change the speed unit.
Accelerator
Power switch
Light and horn
4
Dashboard
5
#1 Speed display or error code, for the error code please check page 7.
#2 Start mode: turn on the scooter, 4 clicks the power switch to change zero/ non-zero start mode.
#3 Speed mode: turn on the scooter, 2 click the power switch to change speed mode, green light is ECO mode.
#4 Speed mode: 6 click the switch to change KM/H or mph speed mode.
#5 Battery signal: To extend the battery life, it's better to charge the battery before 3 grids remain.
#6 Light signal: When front light turn on, the light signal will light up.
#7 Fault signal: If the scooter has an electronic fault, the fault light will turn on. You can check the error code
on page 7.
#8 Lock signal: scooter can be locked by APP, when locked the signal light will turn on.
How free the speed: in the boot status, 8 clicks to free/ limit the speed.
1,Speed display or fualt code
6,Light signal
3,Speed gear
5,Battery signal
8,Lock signal
4,Speed mode
2,Start mode
7,Fualt signal
Eerro Code
6
If the display show fault signal with fault number, you can check and fix as follows
00 Thottle fault: Please check if the throttle back to the default position, or check if the throttle
cable disconnect.
01 E-brake fault: Please check if the brake back to the default position, or check if the brake
cable has broken.
02 Controller fault: Reconnect the controller and battery plug, if still problem, need to send the
controller back to the fact ory to check.
04 Motor hall fault: Please check if the motor hall plug connect well or if the motor cable is broken.
05 Display connention fault: please check if the display cable is broken or plugs connect well.
06 Power switch fault: Please check if the power switch button does not pop up.
07 High temperature alarm: Controller temperature too high, please have a rest for 1 minute.
If still problem, maybe the temperature sensor is broken.
08 Cruise control fault: The cruise control switch button or cable plugs broken.
89 Dashboard signal loss, it is not connected well between the controller and the dashaboard.
Or the controller signal transmission is disturbed.
99 Firmware Upgrade failure: Keep the scooter turn on and connect to the APP to upgrade the
firmware again, please keep the network unblocked
7
1, Open the rubber lid
2, Insert the plug in the port
3, Close the lid after charging
Charger port
8
9
10
11
12
13
14
15
1, Unscrew the bottom screws, open the bottom carefully.
2, Unplugged the XT60 plug and the charger plug
3, The battery is stickered on the scooter bottom, you can pull it out by hand.
16
17
one
3.Tires can be replaced for half a year in normal use, except for punctures.
18
Table of contents
