Toolex 595947 User manual

Page 1
595947
ELECTRIC DRILL BIT
SHARPENER
INSTRUCTION MANUAL

Page 2
1. SPECIFICATIONS
Model Number 595947
Volt/Frequency 240V/50Hz
Input Power 80W
Max. Speed 4200 RPM
Sharpening Size 1/8'' - 17/32'' (3mm - 13mm)
Sharpening Wheel Size 60mm Diameter, 80grit
Net weight 2.95kg
Danger Indicates an imminently hazardous situation which, if not avoided,
will result in death.
Warning Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Caution Indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.
Warning
Read the Instruction manual
Wear eye protection, ear muffs
and helmet
Wear foot protection
Wear gloves
2. SYMBOLS
CONTENTS
1. Specications .................................................................2
2. Symbols ..........................................................................2
3. General Safety Rules ......................................................3
4. Operation ........................................................................4
5. Installation Of Dust proof Cover .....................................6
6. Cleaning .........................................................................6
7. Parts List .........................................................................7

Page 3
Save This Manual
You will need the manual for the safety warnings and cautions, assembly instructions, operating
procedures, maintenance procedures, trouble shooting, parts list, and diagram.
Safety Warning & Cautions
WARNING: When using electric tools, machines, or equipment, basic precautions should always be
followed to reduce the risk of re, electric shock, and personal injury.
3. GENERAL SAFETY RULES
Read All Instructions Before Using This Tool!
1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries.
2. OBSERVE WORK AREA CONDITIONS. Do not use machines or power tools in damp, wet, or
poorly lit locations. Don’t expose to rain. Keep work area well lit. Do not use electrically powered
tools in the presence of ammable gasses or liquids.
3. KEEP CHILD AWAY. Children must never be allowed in the work area. Do not let handle
machines, tools, or extension cords.
4. STORE IDLE EQUIPMENT. When not in use, tools must be locked up in a dry location to inhibit
rust. Always lock up tools and keep out of reach of children.
5. DO NOT FORCE THE TOOL. It will do the job better and more safely at the rate for which it was
intended. Do not use inappropriate attachments in an attempt to exceed the tool’s capacities.
6. USE THE RIGHT TOOL FOR THE JOB. Do not attempt to force a small tool or attachment to do
the work of large industrial tool. Do not use a tool for a purpose for which it was not intended.
7. DRESS PROPERLY. Do not wear loose clothing or jewellery as they can be caught in moving
parts. Protective, electrically nonconducting clothes and Non-slip footwear are recommended
when working. Wear restrictive hair covering to contain long hair.
8. USE EYE AND EAR PROTECTION. Always wear ANSI approved chemical splash goggles when
working with chemicals. Always wear ANSI approved impact safety goggles at other times. Wear
a full face shield if you are producing metal lings or wood chips. Wear an ANSI approved dust
mark or respirator when working around metal, wood, and chemical dusts and mists.
9. DO NOT ABUSE THE POWER CORD. Do not yank it to disconnect it from the receptacle. Do not
carry tools by the cord.
10. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach over or
across running machines.
11. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance.
Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and,
if damaged, have them repaired by an authorized technician. The handles must be kept clean,
dry, and free from oil and grease at all times.
12. DISCONNECT POWER. Unplug when not in use, before servicing, and when changing
accessories.
13. REMOVE ADJUSTING KEYS AND WRENCHES. Make it a habit to check that keys and adjusting
wrenches are removed from the tool or machine work surface before plugging it in.
14. AVOID UNINTENTIONAL STARTING. Be sure the switch is in the OFF position when not in use
and before plugging in. Do not carry any tool with your nger on the trigger, whether it is plugged
in or not.
15. 15. OUTDOOR EXTENSIONS CORDS. When the equipment is operated outdoors, use only
extension cords intended or outside use. See chart under Extension Cords’: For the proper AWG
rating depending on the length of the cord(s) being used.
16. STAY ALERT. Watch what you are doing, use common sense. Do not operate any tool when you
are tired.
17. CHECK DAMAGED PARTS. Before using any tools, any part that appears damaged should be

Page 4
carefully checked to determine that it will operate properly and perform its intended function.
Check for alignment and binding of moving parts; any broken parts or mounting xtures; and any
other condition that may affect proper operation. Any part that is damaged should be properly
repaired or replaced by a qualied technician. Do not use the tool if any switch dose not turn on
and off properly.
18. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces such as
pipes, radiators, and refrigerator enclosures.
19. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement
parts. Use of any other parts will void the warranty. Only use accessories intended for use with
this tool.
20. DO NOT OPERATE TOOL IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read warning
labels on prescriptions to determine if your judgment or reexes are impaired while taking drugs.
If there is any doubt, do not operate the tool.
21. KEEP AWAY FROM LIQUIDS. Tool is designed for dry sharpening operations only.
22. BE CAREFUL OF BITS WHEN SHARPENING. Bits will become hot. Be careful when handling;
allow tips to cool for some time before storing.
23. SHARPENING HEAD MAY BECOME HOT WHILE USING. This is a normal condition and no
cause for alarm. Be careful when handling.
Voltage Warning
Common household current is 220V-240V volts. As long as your tool is rated from 220V-240V there
will be no complications using this tool with household receptacles.
4. OPERATION
FOR PART LISTING REFER TO PAGE 7
1. Take hold 35# (Positioner for Blade), release 36# (Blade Holder) by turning 39# (Locknut). Put drill
bit into 35# - Positioner For Blade (See Fig 1.)
Fig 1.
Fig 2. Fig 3.
2. Press 2# (Button), make 4# (Spring Leaf) expands; (See Fig. 2) Put 40# (Hold Accessory) into 7#
(Fixing Shelf), make 35#(Position for Blade) stuck in 7#(Fixing Shell) at correct position. (See Fig 3.)

Page 5
Fig 4. Fig 5.
3. Adjusting the drill bit position, make the top of drill bit touches 6# (Terminal) rmly, 4# (spring leaf)
pinch the groove of drill bit
(See Fig 4. & 5.)
4. Rotate 39# (Locknut), make 36# (Blade Holder) pinch the drill bit rmly
5. Pull out 40#(the Hold Accessory)and erecting it in 34#(Stand Socket). CAREFULLY make sure
that the heave on 35# (Positioner for Blade) inserts in the groove on 34# (Stand Sockets) , move
the Positioner for Blade from side by side, begin to sharpen. (See Fig 6.)
Where there is no grinding sound between the grinding wheel and the drill, pull out 35#
Accessory and turn it by 180°, and then conduct grinding; the procedure is the same as above
mentioned.
6. Place 35# Accessory on the 14# Spacer, facing back angle of the drill, and turn 35# Accessory
to the left and to the right; conduct grinding. On condition that no grinding sound between
the grinding wheel and the drill, pull out 35# Accessory and turn it by 180°, and then conduct
grinding; the procedure is same as above mentioned; the operation is nished. (See Fig 7.)
Fig 6.
Before Grinding After Grinding

Page 6
5. INSTALLATION OF DUST PROOF COVER
1. Ensure the dust proof cover (30#) is wedged into the base (28#) (See Fig A). Then make the dust
proof cover(30#) level with three sides of the base (See Fig B)
6. CLEANING
1. Make sure to keep the surface of your unit free of grit, dirt, and grease. Use soapy water or non-
toxic solvents. Do not use petroleum based solvents.
2. Keep the air vents free of foreign matter at all times.
2. Push the dust proof cover (30#) forward the front cover (1#) direction. (See Fig C).
3. Make sure the buckle totally clip the cover. The installation is complete. (See Fig D).
Note: The machine can be operated only when it is grounded well. The machine can be started only
when safety is ensured
Other objects or human body should not touch the grinding wheel to avoid accidents
Fig A.
Fig C.
Fig B.
Fig D.

Page 7
Part No. Description Qty. Part No. Description Qty.
1 Top Housing 1 23 Fuse 1
2 Button 1 24 Inductance 1
3 Screw 2 25 Locknut for Fuse block 1
4 Spring Leaf 2 26 Cover 1
5 Screw 2 27 Cushion 4
6 Terminal 1 28 Base 1
7 Fixing Shelf 1 29 Screw 11
8 Screw 2 30 Dust Cap 1
9 Pad 1 31 Cord 1
10 Grinding Wheel 1 32 Connector Board 1
11 Connector 1 34 Screw 4
12 Screw 1 35 Bracket 1
13 Screw 2 36 Stand Socket 1
14 Positioner 1 37 Positioner for Blade 1
15 Screw 2 38 Blade Holder 6
16 Motor 1 39 Steel Spring 6
17 Wire Restraining 1 40 Transition Tube 1
18 Screw 2 41 Locknut 1
19 Switch 1 42 Hold Accessory (Includes 35,36,37,38,39) 1
20 PCB 1 43 Chaffering Ring 1
21 Fuse Block 1 44 Small Cover 1
22 Nut for Fuse 1 48 Big Cover 1
7. PARTS LIST

Page 8
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURE AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR
WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED
TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS
REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO. OR ARISING OUT OF HIS OR
HER INSTALLATION OF REPLACEMENT PARTS THERETO
CONSUMER SERVICE CENTRE
PO BOX 1012
HAMILTON NSW 2303 AUSTRALIA
Made in P.R.C.