Topaz ES/LED/RW/B User manual

www.topaz-usa.com • 925 Waverly Ave • Holtsville, NY 11742 • 800-666-2852 • Fax: [phone]
Items:
ES/LED/RW/B and ES/LED/GW/B
LED EXIT
INSTALLATION INSTRUCTIONS
IMPORTANTSAFEGUARDS
READANDFOLLOWALLSAFETYINSTRUCTIONS
1. Review instruction sheet before beginning installation.
2. All electrical connections must be in accordance with local codes, ordinances, and the National
Electric code.
3. Disconnect power at fuse or circuit breaker before installing or servicing.
4. Not for outdoor use.
5. Do not mount in hazardous locations, or near gas or electric heaters.
6. Do not let power cords touch sharp or hot surface.
7. Equipment should be mounted in locations and at heights where it will not be subjected to
tampering by unauthorized personnel.
8. The use of accessory equipment not recommend by the manufacturer may cause an unsafe
condition.
9. Do not use this equipment for other than intended use.
10. All servicing should be performed by a qualified electrician only.
11. Allow battery to charge for 24 hours before first use.
use Flexible conduit only
SAVETHESEINSTRUCTIONS
MAINTENANCE
Equipment must be tested regularly in accordance with local codes.Replacethe batteriesas neededaccordingtoambient
conditions.No other maintenance required.
OPERATION
Depresstest button.The LED headswillturnonandthe LED indicatorwill turn o Release testbutton, LEDindicatorwill
turn on andLED headswill turn
TROUBLE SHOOTING GUIDE
If LED heads or LED indicatordo notilluminate, checkthe
1. CheckAC supply- verifythatunithas 24 hoursAC supply.
2.
W iringis shortedor batteryis notconnected.
3. Batterydischarge.Permitunit tocharge r 24 hoursthenre-test.
4. If abovetroubleshooting does notsolve theissue, contactmanufacturer r assistance.
1 of2
Read and review safety instructions and diagrams before starting installation.
• All electrical connections must be in accordance with local codes, ordinances, and the
National Electric code. Installation should be performed by a qualified electrician only
• Disconnect power at fuse or circuit breaker before installing or servicing.
• Not for outdoor use.
• Do not mount in hazardous locations, or near gas or electric heaters.
• Do not let power cords touch hot surface.
• Equipment should be mounted in locations and at heights where it will not be subjected
to tampering by unauthorized personnel.
• The use of accessory equipment not recommend by the manufacturer may cause unsafe
operational condition.
• Do not use this equipment for other than intended use.
• After installation is complete, permit battery to charge 24 hours before full duration test.
MAINTENANCE
None required. Equipment must be tested regularly in accor-
dance with local codes. Replace batteries as needed
OPERATION
Press the test button. The LED heads will turn on and the LED
TROUBLE SHOOTING GUIDE: If LED indicator does not illuminate, check the following;
1. Check AC supply - verify that unit has 24 hours AC supply.
2. Unit is shorted or battery is not connected.
3. Battery discharged. Permit unit to charge for 24 hours, then re-test.
4. If above trouble shooting hints do not solve the issue, contact factory for assistance.
OPENING EXIT PANEL
Use flat blade screwdriver to open. Insert screwdriver into

www.topaz-usa.com • 925 Waverly Ave • Holtsville, NY 11742 • 800-666-2852 • Fax: [phone]
Back Mounting (see Diagram 1)
1. Drill ¼” holes into oblong knock outs on back plate (3) to
correspond with junction box (10) holes to be used
2. Feed the transformer input leads through center hole on
housing and make proper connections; for 120VAC, connect
black and white leads to line voltage. For 277VAC, connect
self-powered, be sure to snap battery connector together
3. Feed excess wire into J-Box and secure with back plate
4. Snap in arrows (5) on EXIT panel (2) as required.
5. Connect EXIT face panel (2) to housing; slide top of panel in,
then snap in on the bottom
Side Mounting (see Diagram 2)
1. Attach crossbar(11) to junction box(10). Set the crossbar so
the longer blade is touching the junction box.
2. Open the EXIT housing. Feed the transformer input leads
through side hole, being sure to secure wire into wire guides
molded at the edges of the sign.
3. Attach sign to canopy(7) by inserting canopy into sign
at an angle, then twist to secure.
4. Make the proper supply lead connections. If using 120VAC,
connect the black and white leads to line voltage. If using
wire. If the unit is self-powered, be sure to snap battery
connector together.
5. Push excess wire into junction box and align holes in canopy(7)
with those in crossbar(11). Using screws supplied, tighten
canopy to crossbar so that canopy is securely fastened and
flush against wall.
6. Snap in arrows(5) to EXIT panel(2) as required. Then snap
EXIT panel(2) to housing, top first and then bottom.
Ceiling Mounting (see Diagram 3)
1. Attach crossbar(11) to junction box(10). Set the crossbar so that
the longer blade is touching the junction box.
2. Open the EXIT housing. Feed the transformer input leads
through top hole, being sure to secure wire into wire guides
molded at the edges of the sign.
3. Attach sign to canopy by inserting canopy into sign at an angle,
then twist to secure.
4. Make the proper supply lead connections. If using 120VAC,
connect the black and white leads to the building utility. If using
277VAC, connect the orange and white leads to the building
to snap battery connector together.
5. Push excess wire into junction box and align holes in canopy(7)
with those in crossbar(11). Using screws supplied, tighten
canopy to crossbar so that canopy is securely fastened and
tight against ceiling.
6. Snap in arrows(5) to EXIT panel(2) as required. Then snap EXIT
panel to housing, top first and then bottom.
GREEN GROUND
WIRE
Items:
ES/LED/RW/B and ES/LED/GW/B
LED EXIT
INSTALLATION INSTRUCTIONS