TOPMAQ WB1520D4 User manual

W
W
B
B
1
1
5
5
2
2
0
0
D
D
4
4
W
W
B
B
1
1
5
5
2
2
0
0
D
D
4
4

W
W
B
B
1
1
5
5
2
2
0
0
D
D
4
4

W
W
B
B
1
1
5
5
2
2
0
0
D
D
4
4

W
W
B
B
1
1
5
5
2
2
0
0
D
D
4
4
Bolt(90mm)(7)
1
1
5
5
2
2
0
0
m
m
m
m
6
6
2
2
0
0
m
m
m
m
8
8
2
2
0
0
m
m
m
m
D
D
i
i
m
m
e
e
n
n
s
s
i
i
o
o
n
n
s
s
(
(
I
I
n
n
c
c
l
l
u
u
d
d
e
e
s
s
v
v
i
i
c
c
e
e
)
)
:
:
D
D
r
r
a
a
w
w
e
e
r
r
i
i
n
n
s
s
i
i
d
d
e
e
d
d
i
i
m
m
e
e
n
n
s
s
i
i
o
o
n
n
s
s
(
(
X
X
4
4
)
)
3
3
6
6
5
5
m
m
m
m
4
4
2
2
0
0
m
m
m
m
7
7
0
0
m
m
m
m
M
M
a
a
c
c
h
h
i
i
n
n
e
e
P
P
r
r
o
o
d
d
u
u
c
c
t
t
F
F
e
e
a
a
t
t
u
u
r
r
e
e
s
s
L
L
X
X
W
W
X
X
H
H
L
L
X
X
W
W
X
X
H
H
1. Table Top x 1
2. Shelf x 1
3. Cross Brace x 2
4. Leg x 2
5. Vice x 1
6. Screw(50mm) x 6
7. Bolt(60mm) x 8
8. Connecting Nut x 8
9. Hex Wrench(50mm) x 1
11. Anvil Peg x 4
12. Vice Screw and Washer x 1
13. Screw x 40
14. Sliding Partition x 1
15. Pull-up brace x 1
16. Drawer Front Panel(P1) x 4
17. Drawer Back Panel(P2) x 4
18. Drawer Panel(P3) X 4
19. Drawer Slot Panel(P4) x 4
20. Drawer Bottom(P5) x 4
21. Drawer Handle x 4
22. Drawer Screw x 8

1.Insert the cross nut with groove (8)
into the frame strut (3). Align the cross
nut so that the groove is horizontal.
2.Fasten the frame strut to the foot (4)
with the 60mm screws (7). The groove
of the frame strut must be on the inside.
3.After both feet have been attached to
the frame strut, the shelf (2) is pushed
into the groove.
4.Align the second frame strut (3) and
fasten it again with the cross nuts with
groove (8) and the 60mm screws (7) on
the foot (4). The shelf must snap into
the groove of the frame strut.
W
W
B
B
1
1
5
5
2
2
0
0
D
D
4
4

5.The lower support (15) is attached to
the front with the 50mm screws (6) at
both ends of the feet.
6.The lower support (15) is also
attached to the partition wall with rails
(14) using the 50mm screws (6).
7.The feet are then attached to the
worktop with the 50mm screws (6).
8.The partition is also attached to the
frame with the screws (13). Warning:
there are no pre-drilled holes.
9.Attach the handles (21) to the front of
the drawer (16) with the screws (22).
10.The two side parts of the drawer (18
and 19) are attached to the front of the
drawer with the screws (22).
W
W
B
B
1
1
5
5
2
2
0
0
D
D
4
4

11.Finally, the back of the drawer (17)
is attached to the two side parts. Then
insert the bottom of the drawer.
12.After installing all the drawers,
check whether the inner tracks of the
drawer pull-outs are pushed all the
way forward if not, then push this all the
way forward.
13.Slide the drawers into the guides.
14.Finally, fasten the holding rods (10)
and the bench hooks (11) in the holes
provided on the worktop.
W
W
B
B
1
1
5
5
2
2
0
0
D
D
4
4

W
W
B
B
1
1
5
5
2
2
0
0
D
D
4
4
1. Table Top
2. Shelf
3. Cross Brace
4. Leg
5. Vice
6. Screw(50mm)
7. Bolt(60mm)
8. Connecting Nut
9. Hex Wrench(50mm)
11. Anvil Peg
12. Vice Screw and Washer
13. Screw
14. Sliding Partition
15. Pull-up brace
16. Drawer Front Panel(P1)
17. Drawer Back Panel(P2)
18. Drawer Panel(P3)
19. Drawer Slot Panel(P4)
20. Drawer Bottom(P5)
21. Drawer Handle
22. Drawer Screw
1
4
2316
21
5
11
5 1
2 3 16 21
4