Craftsman 695.65857 User manual

i,CRF FTSM, ,°J
QUICK CLAMPING WORK TABLE I J
BANCO DE TRABAJO DE FIJACION RAPIDA
Model No:
695.65857
Modeio N-°
695.65857
CAUTION:
Before using this
product, read this
manual and follow
all its Safety Rules
and Operating
Instructions.
• Safety
Instructions
• Assembly
• Operation
• Repair Parts
• Espa_ol
PRECAUCI6N:
Antes de usar este
producto, lea este
manual y siga todas
las instrucciones de
seguridad y de
manejo.
• instrucciones de
seguridad
•Montaje
• Manejo
• Repuestos
• Espa_ol
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

WARRANTY.............................................................2
SAFETYINSTRUCTIONS.......................................2
PACKAGECONTENTS...........................................3
ASSEMBLY..............................................................4
HOWTO..................................................................5
SPECIFICATIONS...................................................6
REPAIRPARTS.......................................................6
ESPAI_OL................................................................7
Full One Year Warranty
If this CRAFTSMAN _' Workbench fails to give
complete satisfaction within one year from the
date of purchase, return it to (or contact) the
nearest Sears Service Center in the United
States, and Sears will repair it, free of charge.
This warranty gives you specific legal rights and you
may also have other rights which vary from state to
state.
Sears, Roebuck and Co.,
Dt817WA, Hoffman Estates, IL 60179
DO NOT attempt to assemble or operate your
CRAFTSMAN ®Workbench until you have read the
safety instructions in this section.
Safety items throughout this manual are labeled
with WARNING or CAUTION.
WARNING: Means that failure to follow this safety
statement may result in extensive product damage,
serious personal injury or death.
CAUTION: Means that failure to follow this safety
statement may result in minor or moderate personal
injury, property or equipment damage.
WARNING: DO NOT use this tool for scaffolding or
as a ladder. Make sure to insert pin and fully tighten
handles when in use. Maximum capacity 250 Ibs.
WARNING: Read all instructions.
DO NOT attempt to use your portable workbench
unless the jaw is securely locked in position.
DO NOT load tool stand with more than 250
pounds.
DO NOT apply an unbalanced load which could
result in the workbench tipping over.
DO NOT stand or climb on the workbench. It could
fall or tip over causing serious injury,
Be sure the workbench's leg set frame assembly
is in the fully opened position before using.
When operating a stationary power tool, such as a
miter saw, on your workbench, be sure the tool is
securely bolted to a separate piece of plywood
and the plywood is securely clamped to the
portable workbench. DO NOT clamp or mount
stationary power tools directly to table top. This
could cause serious bodily injury.
When operating a portable power tool such as a
drill, router, sander or planer: Always be sure that
the workpiece is securely clamped to your
workbench. This will avoid kickback which could
cause serious bodily injury.
When using a power tool with the workbench,
ALWAYS follow the safety instructions in the power
tool owner's manual.
ALWAYS wear safety glasses or eye shields when
operating power tools.
To prevent personal injury while opening or closing
your workbench, always avoid positioning hands
or fingers where they could get pinched.
Dress for safety. DO NOT wear loose clothing,
gloves, neckties or jewelry (rings, watches); they
can get caught and draw you into moving parts.
ALWAYS wear non-slip footwear; tie back long hair.
CAUTION: DO NOT store workbench
outdoors or in a damp location.
ALWAYS keep your work area clean, uncluttered
and well lit. DO NOT work on or place workbench
legs on floor surfaces that are slipper/from
sawdust, oil, water or wax.
Keep visitors and children a safe distance away
from the work area, especially when you're
operating a power tool. Visitors should wear the
same safety equipment as the operator.
*SAVE THESE INSTRUCTIONS.

Your CRAFTSMAN _ Workbench is shipped complete
in one carton,
Separate all parts from packing materials and check
each item with Figure 1 and "Table of Loose Parts".
Make sure all items are accounted for before
discarding any of the packing material.
ITEM DESCRIPTION TABLE OF LOOSE PARTS QTY. ITEM DESCRIPTION QTY.
A
B
C
D
"E
F
G
H
I
Leg assembly -left ............................ 1
Leg assembly - right .......................... 1
Foot step ............................................. 1
Screw- M6 x 40 ................................. 8
Washer- medium .... _.......................... 8
Nut - M6 ............................................ 10
Too[ storage rack ................................ 1
Screw- M6 x 12 ................................. 2
Washer - small ................................... 4
J
K
L
M
N
O
P
Q
R
S
Cross bar ..................... 1
Foot pad ...................... 4
Support - table top .............. 4
Table top - front ................ 1
Screws - M8 x 55 ............... 4
Washer- large .......... ,....... 6
Table top - rear ................ t
Nut- M8 .................. ...2
Swivel peg .................... 4
Peg Support ................... 2
B

Assembling the Workbench
'Note: For correct assembly, the legs, [A] and [B],
must have hinges on the outside.
Refer to Figure 2 for steps 1 - 4
,Attach the foot step [C] to the leg assemblies [A &
B] with two screws, [D] (Me x 40), medium
washers [El and nuts IF] (Me) on each side.
Tighten securely.
.Attach the tool storage rack [G] to the leg
assemblies [A & B] with a screw [H] (Me x 12),
two small washers [t], and nut [F] (Me) on each
side. Tighten securely.
,Attach the rear cross bar [J] to the leg
assemblies. Use two screws [D] (Me x 40),
medium washers [E], and nuts [F'J (Me) on each
side. Tighten securely.
4. Install foot pads [K] onto ends of each leg.
Refer to Figure 3 for steps 5 - 8
5. Place the two top supports [L] on the front and top
Figure 2
of the leg assemblies [A & B] with the support's
round extrusions facing up and away from the front
of the table. The bottom round extrusion holes fit
over the threaded extrusions of each screw arm
assembly.
.Place the front table top [M] on the supports [L],
aligning the table top holes over the round
support moldings and press into place. Attach top
using two screws [N] (Me x 55) and two large
washers [O]. Tighten securely.
,Place two table top supports [L] on rear and top
of the leg assemblies [A & B] with the support's
round extrusions facing up and toward the front of
the table. The supports fit into the rectangular
cut-outs in the leg assemblies.
.Place the rear table top [P] on the supports ILl,
aligning the table top holes over the support
extrusions and press into place. Attach top using
two screws [N] (Me x 55) and two large washers
[O] on table top and two large washers [O] and
two nuts [Q] (Me) on table bottom. Tighten
securely.
Figure 3 P
,G
A
D
S
I
/
!
4

Folding Your Workbench
1._Remove any hand tools or parts from table top and
storage rack.
2_ Carefully pull up on hinges, with fingers under
hinge flange, to unlock hinges.
3. qqtt Stand back slightly onto rear legs. (See Figure
4.)
4. Reach down and push front legs backward.
Figure 4
Figure 5
Opening the Workbench
1. Standing at rear of workbench, grasp front edge of
table top and underside of rear cross brace.
2, Pull rear cross brace towards you while
simultaneously pulling up on table top.
3. When fully open, secure in locked position by
pushing on hinges until completely down.
To Adjust Table Top Jaw
Turn the front table top jaw adjustment handles
counterclockwise to move front jaw toward you. Turn
adjustment handles clockwise to move front jaw
away. (See Figure 5.) The table top jaws open to
clamp amaximum 7-inch wide workpiece.
Adjusting Jaw to Angle
Workbench jaw adjusts to a maximum angle of 14
degree s for clamping irregular shaped workpieces.
To adjust jaw to angle, turn either the right or left
djustment handle until desired angle is reached.
Using Adjustable Swivel Pegs - Figure 6
"/our workbench is equipped with 4 swivel pegs. The
swivel pegs can be positioned intoany of the holes in
the front and rear oftop for gripping irregularshaped
workpieces, or to extend gripping and clamping when
the workpiece exceeds the jaw capacity.
CAUTION: Swivel pegs are to be used to grip
workpiece only in cases where the workpiece DOES
NOT extend beyond the surface of the jaw.
Figure 6

Work Table Area: 30" x 13-1/4".
Maximum Weight Support: 250 pounds.
Working.Heights: 31-!/2"
695.65857 Workbench
1" BB
x--_
NO.
A
B
C
D
E
F
G
H
i
J
K
L
M
N
O
P
Q
R
$
PART NO.
119800362
119800363
116600047
116600048
116620265
117010212
117020161
117020172
117020176
117010213
117010214
117010215
1170102T6
117010217
117010218
117220185
116710002
116710029
116710118
DESCRIPTION QTY,
Table Top - Front......................... 1
Table Top -Rear .......................... 1
Handle ......................................... 2U
Handle Grip ................................. 2 V
Threaded Piece ........................... 2
Rail .............................................. 2 W
Tool Rack .................................... 1 X
Foot Step ..................................... 1 Y
Cross Bar .................................... 1 Z
L Bracket - Hinge - Rear ............. 2
L Bracket - Hinge - Front ............ 2 AA
LBracket - Left............................ 1 BB
L Bracket - Right ......................... 1 CC
LL - Right ....................................2 DD
Leg ..............................................4
Spindle Threaded ........................ 2 EE
Rivet ............................................2 FF
Screw Handle to Spindle
(M3.gx13) ....................................2 GG
Screw Grip to Handle HH
(M4.2x9.5) ...................................2II
KEY
NO. PART NO,
T 116700081
116750142
116710020
116700026
116630201
116610118
116750142
116720040
117710091
116700021
116700023
116720112
116720077
116600014
1!6610rt,2-"
116610723
DESCRIPTION QTY,
Screw - Legs and L Brackets
(M6x45) ....................................... 6
Screw -L Brackets (M6x40) .......4
Lock Nut -Legs and L
Brackets..; ................................. 10
Washer - L Brackets .................. 4
Foot Pad...................................... 4 ,I
Connector Table Top Supports...4
Screw for Foot Step and
Cross Brace (M6x40) .................. 8
Screw -Tool Rack (M6x12) ........ 2
Screw - Table Top (M8x55) ......... 4
Nut - Table Top - Rear (MS)....... :2
Nut - Tool Rack, Foot Step
and Cross Bar (M6) .................. 10
Washer - TableTops ................... 6
Washer - Foot Step and
Cross Bar ....................................8
Washer -ToolRack ....................4 =_
SwivelPeg ..................................4
Peg Support................................2
PART SET
_119900868
119900871
119900868